Sony MEX-GS600BT Service Manual ▷ View online
MEX-GS600BT
17
3-11. CHASSIS (OP) ASSY
3-12. CHUCKING ARM SUB ASSY
6 two coil springs (damper) (natural)
7 coil spring (damper) (blue)
8 chassis (OP) assy
5
1 tension spring (KF)
2 gear (LE1)
3 lever (D)
4 slider (R)
3 chucking arm sub assy
2
1 spring
Note 1: Have this portion receive the chassis.
Note 1: Have this portion receive the chassis.
Note 2: Be careful not to touch the turn table.
MEX-GS600BT
18
3-13. SLED MOTOR ASSY
3 sled motor assy
sled motor assy
1 spring
spring
stand
stand
turn table
2 three serration screws
(M2
u 3)
three
serration
screws
(M2
u 3)
bearing (F)
bearing (R)
Note 1: Place the stand with care not to touch the turn table.
Note 2: Never remove these parts since they were adjusted.
Note 3: Take care to prevent the chassis from being bent
when tightening the three machine screws.
1RWHIRU$VVHPEO\
–
ERWWRPVLGHYLHZ
–
–
ERWWRPVLGHYLHZ
–
–
ERWWRPVLGHYLHZ
–
MEX-GS600BT
19
3-14. OPTICAL PICK-UP SECTION
3-15. OPTICAL PICK-UP
1
2 optical pick-up section
Note: Be careful not to touch the lens and hologram
terminal when removing the optical pick-up section.
–
bottom side view
–
There is space at the end of the
leaf spring (OPS) to avoid
contact with the slide.
leaf spring (OPS) to avoid
contact with the slide.
5 optical pick-up
4 lead screw assy
Prevent the end of the
leaf spring (OPS) from being
in contact with the OP slide base.
leaf spring (OPS) from being
in contact with the OP slide base.
Prevent the end of the
leaf spring (OPS) from being
in contact with the OP slide base.
leaf spring (OPS) from being
in contact with the OP slide base.
1 tapping screw
(P
1.4)
2 leaf spring (OPS)
3 rack
–
bottom side view
–
Notes for Assembly
MEX-GS600BT
20
SECTION 4
TEST MODE
SETTING THE TEST MODE
Setting method:
1. Press the [
1. Press the [
OFF SOURCE] button for 1 second to turn the
power off.
2. Press the [SHUF 4] t [MIC/ZAP 5] t [V
ALBUM 1] but-
tons sequentially (the [V
ALBUM 1] button is pressed for two
seconds).
3. It is set to the test mode, and all segments of the liquid crystal
display light.
Releasing method:
Press the [
Press the [
OFF SOURCE] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confi rm the state of the external microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
To confi rm the state of the external microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
Procedure:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
OFF SOURCE] button to select the Bluetooth
Phone function.
3. On/off of the microphone audio loopback function changes
whenever the [ALBUM v
2] button is pressed (“ALBM” is
displayed in the liquid crystal display).
LOOPBACK
ALBM
ON
Lit
OFF
None
Click on the first or last page to see other MEX-GS600BT service manuals if exist.