Sony MEX-1HD Service Manual ▷ View online
25
MEX-1HD
6. With the track number 1 selected, press the right jog button
(PUSH LIST). (A check mark will be displayed on the right
side of track number 1 only)
side of track number 1 only)
7. Press the
[ REC]
button to start the recording.
8. Check that the progress bar is processing and remaining amount
of time for recording indicated next to the bar is decreasing.
9. Press the function 1 (s) button to quit recording.
Ver 1.2
dial (PUSH LIST), and press the right jog button (PUSH LIST)
to enter the ID COPY mode.
to enter the ID COPY mode.
9. Input the password for ID copy with the right jog dial and
button (PUSH LIST).
10. Rotate the right jog dial (PUSH LIST) to select the “(OK)”,
and press the right jog button (PUSH LIST) to execute ID copy
to the HDD of the system ID.
to the HDD of the system ID.
11. Upon successful completion of ID copy, if the “ID-COPY OK”
is displayed, release the test mode. (Power off)
• Data installing to the HDD (User Upgrade type only)
Note 1:
This operation is required for the User Upgrade type only. For
Initial Lot type, skip this operation and go to the next step “Op-
eration check”.
Initial Lot type, skip this operation and go to the next step “Op-
eration check”.
Note 2:
Data installing may fail, if there is less available space in the
hard disk.
If data installing failed, make a checking through the following
procedure. Less space remains if “FULL CAPACITY” is dis-
played.
Checking procedure:
(1) In the standby state with normal mode, press the
hard disk.
If data installing failed, make a checking through the following
procedure. Less space remains if “FULL CAPACITY” is dis-
played.
Checking procedure:
(1) In the standby state with normal mode, press the
[M]
(MENU)
button to display the menu screen.
(2) Rotate the right jog dial (PUSH LIST) to select the “Library”,
and press the right jog button (PUSH LIST) to enter the Li-
brary mode.
brary mode.
(3) Rotate the right jog dial (PUSH LIST) to select the “CDDB
Install”, and press the right jog button (PUSH LIST) and
display confirmation screen of start the processing.
display confirmation screen of start the processing.
(4) Rotate the right jog dial (PUSH LIST) to select the “OK”,
and press the right jog button (PUSH LIST). Less space re-
mains if “FULL CAPACITY” is displayed.
mains if “FULL CAPACITY” is displayed.
1. When the power is turned on, the initial setting screen is dis-
played. Press the right jog button (PUSH LIST) button repeat-
edly until tentative setting completed.
edly until tentative setting completed.
Note:
Exact date and time need not be set.
2. Chech the version of CD-R for service and insert the disc to
the set.
3. Again in the test mode, select the “Test Mode” from the test
mode main menu by rotating the right jog dial (PUSH LIST)
and press the right jog button (PUSH LIST) to enter the Test
Mode.
and press the right jog button (PUSH LIST) to enter the Test
Mode.
4. Rotate the right jog dial (PUSH LIST) to select the “IN-
STALL”, and press the right jog button (PUSH LIST) to enter
the INSTALL mode.
the INSTALL mode.
5. Rotate the right jog dial (PUSH LIST) to select the “ALL(U)”,
and press the right jog button (PUSH LIST), and the “IN-
STALL-ALL(U) “ will be displayed and the installation will
start soon.
(process time: about 30 minutes)
STALL-ALL(U) “ will be displayed and the installation will
start soon.
(process time: about 30 minutes)
6. Upon successful completion of installation, the “INSTALL-
ALL(U) OK” will be displayed, and then remove the CD-R
for service and release the test mode. (Power off)
for service and release the test mode. (Power off)
• Operation check
1. Turn the power on again, and the initial setting screen will be
1. Turn the power on again, and the initial setting screen will be
displayed. Then, press the right jog button (PUSH LIST) but-
ton repeatedly until tentative setting completed.
ton repeatedly until tentative setting completed.
Note:
Exact date and time need not be set.
2. In the normal mode, press the
[SOURCE]
button to select the
HDD mode and play recorded contents. Check that the recorded
contents are played back normally.
contents are played back normally.
3. Insert a music CD and press the
[SOURCE]
button to play.
4. Press the
[ REC]
button, rotate the right jog dial (PUSH
LIST) to select the third item (musical note mark), and press
the right jog button (PUSH LIST).
the right jog button (PUSH LIST).
5. Press the function button 2 (ALL) to cancel the selection of all
tracks. (A check mark on the right side of track number will
disappear)
disappear)
z
z
26
MEX-1HD
4. Rotate the right jog dial (PUSH LIST) to select the “IN-
STALL”, and press the right jog button (PUSH LIST) to enter
the INSTALL mode.
the INSTALL mode.
5. Rotate the right jog dial (PUSH LIST) to select the “ALL(U)”,
and press the right jog button (PUSH LIST), and the “IN-
STALL-ALL(U)” will be displayed and the installation will
start soon.
(process time: about 10 seconds (Initial Lot type), about 30
minutes (User Upgrade type))
STALL-ALL(U)” will be displayed and the installation will
start soon.
(process time: about 10 seconds (Initial Lot type), about 30
minutes (User Upgrade type))
6. Upon successful completion of installation, the “INSTALL-
ALL(U) OK” will be displayed, and then remove the CD-R
for service and exit the test mode. (Power off)
for service and exit the test mode. (Power off)
• Operation check
1. Turn the power on again, and the initial setting screen will be
1. Turn the power on again, and the initial setting screen will be
displayed. Then, press the right jog button (PUSH LIST) but-
ton repeatedly until tentative setting completed.
ton repeatedly until tentative setting completed.
Note:
Exact date and time need not be set.
2. Insert a music CD and press the
[SOURCE]
button to play.
3. Press the
[ REC]
button, rotate the right jog dial (PUSH
LIST) to select the third item (musical note mark), and press
the right jog button (PUSH LIST).
the right jog button (PUSH LIST).
4. Press the function button 2 (ALL) to cancel the selection of all
tracks. (A check mark on the right side of track number will
disappear)
disappear)
5. With the track number 1 selected, press the right jog button
(PUSH LIST). (A check mark will be displayed on the right
side of track number 1 only)
side of track number 1 only)
6. Press the
[ REC]
button to start the recording.
7. Upon completion of the recording, a peep will be heard and
the
[ REC]
button will change its color from red to blue.
8. Press the
[SOURCE]
button to start the play of HDD. Check
that the HDD is played back normally.
• Factory Setting
Note:
The “Factory Setting” command deletes the data recorded on the
hard disk. Only if the hard disk drive was replaced, execute this
command to erase the data for operation check before returning the
set to the customer.
hard disk. Only if the hard disk drive was replaced, execute this
command to erase the data for operation check before returning the
set to the customer.
1. Remove the CD and press the
[OFF]
button to activate the
standby state, and then enter the test mode.
2. Select the “Test Mode” from the test mode main menu by ro-
tating the right jog dial (PUSH LIST) and press the right jog
button (PUSH LIST) to enter the Test Mode.
button (PUSH LIST) to enter the Test Mode.
3. Rotate the right jog dial (PUSH LIST) to select the “Factory
Setting”, and press the right jog button (PUSH LIST) to start
the processing.
the processing.
4. Upon completion of all of the processing, “Factory Setting-
OK” will be displayed, and then the system will be reset and
will restart automatically.
will restart automatically.
Ver 1.2
3) When The Only HDD Was Replaced
Note:
Executing this operation without replacing the hard disk drive
causes the user data to be erased. Accordingly, do not execute
this operation by mistake.
this operation by mistake.
When the hard disk drive (HDD) was replaced, the processing such
as formatting is required. After the HDD replacement, be sure to
execute all of the following steps.
as formatting is required. After the HDD replacement, be sure to
execute all of the following steps.
1. HDD replacement
r
2. HDD formatting
r
3. ID copy to the HDD
r
4. Data installing to the HDD
r
5. Operation check
r
6. The Factory Setting
Procedure:
• HDD formatting
1. After replacing the HDD, turn the power on and enter the test
• HDD formatting
1. After replacing the HDD, turn the power on and enter the test
mode. (Refer to page 21 “Entering The Test Mode”)
2. Select the “Test Mode” from the test mode main menu by ro-
tating the right jog dial (PUSH LIST), and press the right jog
button (PUSH LIST) to enter the Test Mode.
button (PUSH LIST) to enter the Test Mode.
3. Rotate the right jog dial (PUSH LIST) to select the “HDD”,
and press the right jog button (PUSH LIST) to enter the HDD
mode.
mode.
4. Rotate the right jog dial (PUSH LIST) to select the “FOR-
MAT”, and press the right jog button (PUSH LIST) to enter
the FORMAT mode.
the FORMAT mode.
5. With the Format mode activated, press the right jog button
(PUSH LIST), and the “HDD-FORMAT hddDbInit...” will be
displayed and then the HDD formatting will start soon.
displayed and then the HDD formatting will start soon.
6. Upon successful completion of HDD formatting, “HDD-FOR-
MAT OK” will be displayed. Then, press the right jog button
(PUSH LIST) to return to the FORMAT menu, and further
press the function button 1 to return to the HDD menu.
(PUSH LIST) to return to the FORMAT menu, and further
press the function button 1 to return to the HDD menu.
• ID copy to the HDD
1. Select the “ID” from the HDD menu by rotating the right jog
1. Select the “ID” from the HDD menu by rotating the right jog
dial (PUSH LIST), and press the right jog button (PUSH LIST)
to enter the ID mode.
to enter the ID mode.
2. Rotate the right jog dial (PUSH LIST) to select the “COPY”,
and press the right jog button (PUSH LIST) to enter the ID
COPY mode.
COPY mode.
3. Rotate the right jog dial (PUSH LIST) to select the “(OK)”,
and press the right jog button (PUSH LIST) to execute ID copy
to the HDD of the system ID.
to the HDD of the system ID.
4. Upon successful completion of ID copy, if the “ID-COPY OK”
is displayed, release the test mode. (Power off)
• Data installing to the HDD
1. When the power is turned on, the initial setting screen is dis-
1. When the power is turned on, the initial setting screen is dis-
played. Press the right jog button (PUSH LIST) button repeat-
edly until tentative setting completed.
edly until tentative setting completed.
Note:
Exact date and time need not be set.
2. Chech the version of CD-R for service and insert the disc to
the set.
3. Again in the test mode, select the “Test Mode” from the test
mode main menu by rotating the right jog dial (PUSH LIST)
and press the right jog button (PUSH LIST) to enter the Test
Mode.
and press the right jog button (PUSH LIST) to enter the Test
Mode.
z
z
z
MEX-1HD
27
27
SECTION 6
DIAGRAMS
6-1.
BLOCK DIAGRAM – SERVO, HD/MS/USB INTERFACE Section –
33
124
125
141
142
163
165
143
144
140
150
145
151
152
166
36
16
23
17
11
10
13
33
31
7
32
30
7
1-5, 10-20, 31
2-6, 8-18, 32
8
AUTOMATIC
POWER CONTROL
Q1
AMP
IC3
12
21-23, 25-29
19, 20, 25-30
OPTICAL PICK-UP
BLOCK
DAX-21EG
VCC
RF
A
B
F
E
LD
PD
FCS (+)
FCS (–)
FCS (–)
TRK (+)
TRK (–)
TRK (–)
VO3+
VO3–
VO2+
VO2–
VO1–
FIN1
5 RFA–
EFMIN
EFMIN2
PH
BH
RHLD
EQS
RREC
FE
AD1
FBSL
TE
TBAL
SGC
GHS
VO1+
RFSM
PH
35
BH
32
RHLD
18
EQS
30
REFL
28
FE
21
FBAL
26
TE
20
TBAL
19
SGC
16
GHS
VIN3
PSEN
W
G
E
ZCE
WSTROBE
DATA0 – DATA7
A0 – A16
A0 – A16
DQ0 – DQ7
FLASH
MEMORY
IC9
68-75, 77-84
DD0 – DD15
ID_DD00 – ID_DD15
CPU/ATA INTERFACE
IC2003 (1/2)
ATAPI, DSP,
CD-ROM DECODER
IC8
RF AMP,
FOCUS/TRACKING ERROR AMP
IC1
FOCUS/TRACKING COIL DRIVE,
SLED MOTOR DRIVE
IC6
A_5V
7 FIN2
9 E
10 F
13
14
LDD
BUFFER
IC12
5
VIN2
3
VIN1
8
STBY
1
3
19
20
UOUT
VOUT
WOUT
UIN
17
VM3
SPINDLE
MOTOR DRIVE
IC5
XIDE-RST
D5V
4
VIN
5
WIN
6
COM
11
FG
13
BRK+
14
STBY
8
CSL1
9
CSL2
+2V
REGULATOR
IC2
LD ON
Q10
LEVEL SHIFT
Q6, 7
STANDBY SWITCH
Q9
STANDBY SWITCH
Q5
PHASE CONTROL
Q2 – 4
BRAKE SWITCH
Q8
128 ID1_XCS1
49
ZCS3FX
127 ID1_XCS0
50
ZCS1FX
115 ID1_INTR
59
HINTRQ
117 ID1_XDMAK
60
ZDMACK
122
110
111
112
123
124
125
113
116 118
ID1_DMRQ
64
DMARQ
LDS
146 TES
24
TS
164 TSH
153 TOFST
157 FDO
156 TDO
158 SLDO
108 IOPORT6
171 IOPORT11
159 SPDO
113 IOPORT7
169 FG
170 IOPORT10
175 ZRESET
22
35
TSH
167 LDON
IOPORT1
15
LDON
TRACKING
OFFSET
IC10
M
M102
(SLED)
M101
(SPINDLE)
U
W
V
87, 88, 90-92, 94, 95, 97-99,
101, 102, 104, 105, 107, 108
92
93
X1
33.8688MHz
XTALCK
XTAL
DA1
IORDY
ZDIOR
ZDIOW
54
56
53
61
62
63
DA0
DA2
DA1
IORDY
ZDIOR
ZDIOW
ZDIOW
DA0
DA2
ID_DA1
ID_IORDY
ID_XDIOR
ID_XDIOW
ID_XDIOW
ID_DA0
ID_DA2
DA1
IORDY
ZDIOR
ZDIOW
ZDIOW
DA0
DA2
IDESA0
IDED0 –
IDED15
IDESA1
IDESA2
IDERDY
HARD DISK
DRIVE UNIT
XIDEIOR
XIDEIOW
AT
API DA
TA BUS
AT
API DA
TA BUS
HD0 –
HD15
HD0 – HD15
HD0 – HD15
DA
TA BUS
ADDRESS BUS
DA
TA BUS
ADDRESS BUS
DATA BUS
ADDRESS BUS
22
21
20
26
59-63, 65, 66,
69-71, 73-77
39-44, 47-52,
54-56, 58
B+ SWITCH
Q4201, 4202
CN4201
CN4101
PS4100
D5V
4
8
2
2
6
3
3
1
9
DIO
SCLK
BS
INS
VCC
VCC
11
SW
XMS_DET0
MS_PWR
XMS_DET1
DATA+
DATA–
VCC
D3.3V
D4205
D4206
DIO
SCLK
BS
INS
85 XIRQ
DSP, MAGIC GATE CORE,
MEMORY STICK INTERFACE
IC4001
ADR0 – ADR14
DB0 – DB15
SH_D0 –
SH_D15
SH_A1 –
SH_A15
187-184, 182,
181, 179-163
188-194, 196,
197, 199-205
SH_A01 – SH_A20,
SH_A23 – SH_A25
SH_A01 – SH_A20,
SH_A23 – SH_A25
SH_D00 –
SH_D15
SH_D0 – SH_D15
63, 64, 2-7,
9-14, 16, 17
USB INTERFACE
IC4301
A0, A1
D0 – D15
SH_D0 –
SH_D15
SH_A1, SH_A2
MEMORY STICK
D
FS256
BCLK
33
16
32
31
SDO
LRCK
MCLK
BCLK
SDO
LRCK
92
3
91
4
95
2
93
1
17
7
18
6
SIOSO
EXT_XIRQ0
EXT_XIRQ1
51
H_D1+
50
H_D1–
SIOSI
SIOCK
SIOCS
DP0
DP1
DI
DO
XSC
XCS
RDY/XBSY
RESET
EEPROM
IC4002
I/O
59, 60
XWRL
XCS
XRST
78
81
80
82
13
INT1
29
XRD
XWRU
XWE0
XCS5
XD1859_RST
XRD
XWE1
XCLOSE_END
A
(Page 29)
B
(Page 28)
IDO_INTR
IDO_XDMAK
IDO_XCS0
IDO_XCS1
IDO_DMRQ
119
120
147
146
IDEIRQ
XIDEDAK
XIDECS1
XIDECS0
IDEDRQ
HDD_LED
SH_D0 – SH_D15
SH_A1 – SH_A20,
SH_A23 – SH_A25
D2000
HDD
(Page 29)
E
(Page 28)
I
(Page 28)
H
(Page 28 )
F
(Page 28)
WR_N
22
23
RD_N
XWE0
XRD
G
(Page 28)
DREQ1
RESET_N
21
25
27
32
CS_N
DACK1
XDREQ0
XUSB_RST
XCS2
XDACK0
C
(Page 29)
2
3
X4001
22.579MHz
XTAL0
EXTAL0
9
10
X4002
20MHz
XTAL1
EXTAL1
RESET SIGNAL
GENERATOR
IC7
D2001
• SIGNAL PATH
: CD PLAY
: MEMORY STICK PLAY
: USB IN
MEX-1HD
28
28
6-2.
BLOCK DIAGRAM – CPU, DISPLAY Section –
DQ0 – DQ15
2, 3, 5, 6, 8, 9, 11, 12, 39,
40, 42, 43, 45, 46, 48, 49
AV_HD00 – AD_HD15
43-46, 48, 49, 51-54,
56, 57, 59-62
HD0 – HD15
15, 16, 18, 34, 36-38,
54-57, 59, 60, 78, 80, 88
SH_D0 – SH_D15
SH_A1 – SH_A25
AI<0>, AI<1>
DI<1> – DI<15>
SD_D00 – SD_D15
206-208, 2, 3, 5,
6, 8, 9, 11-17
SD_A00 – SD_A11
42-38, 36, 35,
33-31, 29, 28
35
21
18
26
17
25
16
24
15
23
14
18
CLK
XCS
XRAS
XCAS
XWE
LDQM
SD_CLK
SD_XCS1
SD_XRAS
SD_XCAS
SD_XWE
SD_DQML
36
19
UDQM
SD_DQMU
33
DACK1
DACKI
40 DREQO
42
XCS6
CS6I
41
XWE0
WEI
32
XSYS_RST
RSTI
29
4
SOO
SI
FL+48V
F (+) 4.3V
F (–) 1.0V
F (+) 4.3V
F (–) 1.0V
28
9
SCKO
CLK
34
8
BKO
BK
31
7
LATO
LAT
14 SI
11 SCK
12 RCK
43
MCKI
26
30
FLD_ON
FL_DONI
64
41
65
62
66
83
68
97
69
89
70
AV_BEND1
AV_BEND2
AV_BEND3
XAV_DRQ1
XAV_DRQ2
XAV_DRQ3
EXT_INT5
EXT_INT6
EXT_INT7
TOUT0
TOUT1
DX1
78
AV_HRXW
HR/XW
11
12
XWE
XRESET
26
28
XCE
XOE
15
LDQM
16
17
XWE
XCAS
18
XRAS
19 37
XCS
CKE
38
CLK
39
UDQM
72
5
74
7
79
6
XAV_HRDY
XAV_HDS
XAV_HCS0
87
XHDS1
96
XHCS
96
99
XCS0
31
30
29
XHRDY
XHDS
XHCS
44
PGND
33
XRST
PRDY
8 XIRL0
SH_XIRL0
SH_XIRL1
SH_XIRL2
SH_XIRL3
SH_XBS
SH_XCS
SH_XWAIT
XPDS
XPCS
75
76
77
AV_HA1
AV_HA2
AV_HA3
HHWIL
HCNTL0
HCNTL1
81
42
AV_CMD
EXT_INT4
83
XAV_HINT0
XHINT
BA, A0 – A10
20-24, 27-32
CPU/ATA INTERFACE
IC2003 (2/2)
CPU
IC1010
128Mbit SD-RAM
IC1020
64Mbit FLASH MEMORY
IC1030
DSP
IC3003
COMPLEX PROGRAMMABLE
LOGIC DEVICE
IC3000
16Mbit SD-RAM
IC2001
112
102
103
13
XRESET
XHB_RST
186
EXTAL
156
130
120
XHRDY 111
CASL 108
XRAS3 106
XCS3
CKE
CASL
XRAS3
XCS3
CKE
CASL
XRAS3
XCS3
CKE
105
102
115
148
9
28
30
XIRL1
149
10 XIRL2
150
11 XIRL3
151
87 XBS
158
XWE0
89 XWE0/DQMLL
156
SH_XWE1
90 XWE1/DQMLU
157
SH_XRD
88 XRD
154
SH_XRDWR
93 RDXWR
155
XCS4
162
XWAIT
152
100
SH_CKIO
CKIO
160
162
SH_XRST 153
123
101
187
114
191
185
104
SH_D0 –
SH_D15
SH_D0 –
SH_D15
SH_D0 –
SH_D15
SH_A1 –
SH_A25
SH_A1 –
SH_A22
SH_A1 –
SH_A14
DATA BUS
ADDRESS BUS
DATA BUS
ADDRESS BUS
DA
TA BUS
ADDRESS BUS
DA
TA BUS
ADDRESS BUS
SH_D0 – SH_D15
SH_A1 – SH_A20,
SH_A23 – SH_A25
I
(Page 27)
F
(Page 27)
G
(Page 27)
J
(Page 30)
K
(Page 29)
H
(Page 27)
SH_D0 –
SH_D15
SH_A1,
SH_A2
DQ0 – DQ14,
DQ15/A-1
29-36, 38-45
A0 – A13
20-26, 29-35
A0 – A21
1-10, 13, 16-25, 48
54-56, 58, 60-68, 70,
72-78, 80, 82, 84, 86
52-48, 46,
44-36, 34
44, 1
AI<0>, AI<1>
15, 1-3
23-18, 16, 14-12,
8-5, 3, 2
DQ0 – DQ15
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
XD1859_RST
XDREQ0
XUSB_RST
193
XSYS_RST
180 MS_PWR
98
XCS5
XCS2
XDACK0
XD1859_RST
XDREQ0
XUSB_RST
XSYS_RST
D524
XCS5
XWE0, XWE1, XRD,
XCS5, XD1859_RST
XCS5, XD1859_RST
179 XIDE_RST
B
(Page 27)
XIDE_RST
E
(Page 27)
MS_PWR
XWE0, XRD, XDACK0,
XCS2, XDREQ0, XUSB_RST
XCS2, XDREQ0, XUSB_RST
XCS2
XDACK0
RDXWR
XWE1
XRD
CKIO
XWE0
XWE1
XRD
XRD
XWE0
XWE0
RDXWR
XWE1
XRD
XSYS_RST
CKIO
XWE0
XDREQ1 192
SA_DATA 200
SA_CLK 159
190
D_MUTING
SA_DATA
FL_ON, ILL_ON,
FLD_ON
SA_DATA, SA_CLK,
D_MUTING
SA_CLK
D_MUTING
FL_ON
ILL_ON
32
MS_ACS_LED
FL_ON
FLD_ON
ILL_ON
SUB_RXD 168
SUB_TXD 174
188
SH_WDT
SUB_TXD
SUB_RXD
SH_WDT
OSCILLATOR
IC5002
DISPLAY CONTROLLER
IC5001
LED CONTROL
IC901
SYSTEM CONTROLLER
IC501 (1/3)
D921-936, 947,
D950, D951, LSW901
FLUORESCENT
INDICATOR TUBE
FL900
LED DRIVE
Q900, 901,
Q900, 901,
Q909-911
X1001
33.3333MHz
3
X3002
37.5MHz
CLKIN
RE_LA
109
RE_LB
110
107 RE_RA
1
CN901
3
CN524
108
106
RE_RB
LED DRIVE
Q4203
D4201
31
USB_ACS_LED
LED DRIVE
Q4204
D4202
I/O
SUB_RXD
SH_WDT
SUB_TXD
13
12
67
82
SUB_TXD/FLS_SO
SUB_RXD/FLS_SI
SH_WDT
FLS_ON
LEVEL SHIFT
IC601
ROTARY ENCODER
ENC900
LEVEL SHIFT
IC602
7
XMAIN_RST
XNOSE_SW
VOL
PUSH SOUND
MEMORY
STICK
ROTARY ENCODER
ENC901
.
– +>
PUSH LIST
Click on the first or last page to see other MEX-1HD service manuals if exist.