Sony CDX-M850MP Service Manual ▷ View online
17
CDX-M850MP
3-6. CAM (R)
3-5. ARM (A-R) ASSY, ARM (B-R) ASSY
1
Move the arm (B-R) assy in the direction of the
arrow
arrow
A
and the arm (A-R) assy in the direction of
the arrow
B
fully (full open state).
2
Align the hole (large) on the cam (R) with part
C
and
install the cam.
4
Turn the cam (R) clockwise and counterclockwise to
verify that both the arms are operated.
verify that both the arms are operated.
bracket (R) assy
3
arm (A-R) assy
4
type-E stop ring 1.5
2
type-E stop ring 1.5
1
arm (B-R) assy
3
type-E stop ring 1.5
5
oil damper
6
screw (P 2x4)
cam (R)
B
A
C
arm (B-R) assy
hole (large)
line
arm (A-R) assy
18
CDX-M850MP
SECTION 4
DIAGRAMS
4-1. IC PIN DESCRIPTIONS
• IC3 HD6432238RWN35TEI (CD MASTER CONTROL) (SERVO Board (2/2))
Pin No.
Pin Name
I/O
Pin Description
1
TEST
I
Test mode selection pin Not used. (Open)
2
DECXRST
O
Reset signal output to the DSP IC “L”: reset
3
DECSTBY
O
Standby mode control signal output to the DSP IC “H”: standby
4 – 7
NC
O
Not used. (Open)
8
PH3
I
CD PH3 photo sensor detection signal input Not used. (Open)
9
INSW/PH2
I
CD mechanism disc in switch detection signal input
10
LIMIT_SW
I
CD mechanism in-limit switch detection signal input
11
D_SW
I
CD mechanism down switch detection signal input
12
CVCC
—
System power supply pin (+3.3 V)
13
NC
O
Not used. (Open)
14
VSS
—
Ground pin
15
NC
O
Not used. (Open)
16
PH1
I
CD PH1 photo sensor detection signal input Not used. (Open)
17
EJECT
O
CD mechanism loading motor control signal output (eject operation)
18
LOAD
O
CD mechanism loading motor control signal output (load operation)
19 – 26
NC
O
Not used. (Open)
27
FLAG
I
Correction unable detection signal input
28
RFOK
I
RFOK signal input from the servo IC
29, 30
NC
O
Not used. (Open)
31
TXD
O
UART TXD PC connection output Not used. (Open)
32
RXD
I
UART RXD PC connection input Not used. (Open)
33
XTALEN
O
Crystal oscillation control signal output to the servo IC
34
TSTB
O
CD text parameter strobe signal output to the servo IC
35
STB
O
Data strobe signal output to the servo IC
36
A0
O
Command/parameter identification signal output to the servo IC
“L”: command, “H”: parameter
37
CD_RST
O
Reset signal output to the servo IC
38
PACK
I
CD text pack sync signal input from the servo IC
39
NC
O
Not used. (Open)
40
SELF_SW
I
CD mechanism self load position detection switch signal input
41
NC
O
Not used. (Open)
42
AVSS
—
Ground for A/D converter
43, 44
NC
O
Not used. (Open)
45, 46
NC
I
Not used. (Open)
47
KEY0
I
Key switch signal input in the test mode Not used. (Open)
48
KEY1
I
Mode switch signal input in the test mode Not used. (Open)
49 – 52
NC
I
Not used. (Open)
53
AVREF
—
Reference voltage for A/D converter
54
AVCC
—
Power supply for A/D converter
55
MD0
—
CPU operation mode setting pin Connecting to +3.3 V in this set.
56
MD1
—
CPU operation mode setting pin Connecting to +3.3 V in this set.
57
X1A
—
Sub clock oscillator terminal Not used. (Open)
58
X0A
—
Sub clock oscillator terminal Not used. (Open)
59
RSTX
I
Microcomputer reset signal input
60
NMI
—
Not used. (Fixed at “H”)
61
STBY
—
Not used. (Fixed at “H”)
62
VCC
—
Power supply pin (+3.3 V)
63
XTAL
—
Main clock oscillator pin (12.288 MHz)
64
VSS
—
Ground pin
65
XTEAL
—
Main clock oscillator pin (12.288 MHz)
66
FWE
I
Flash write enable signal input
19
CDX-M850MP
Pin No.
Pin Name
I/O
Pin Description
67
MD2
—
CPU operation mode setting pin
68
FL_BOOT
I
Flash write selection signal input (“L”: flash write mode)
69
FL_W
O
Flash write control signal output connected to pin 66 (FWE)
70
NC
O
Not used. (Open)
71
CDMON
O
CD mechanism power supply control signal output
72
DECINT
I
Interrupt signal input from the DSP IC
73
CLOSE
O
Front panel operation request output (Close)
74
OPEN
O
Front panel oparation request output (Open)
75
LINKOFF
O
LINK OFF signal output for UNI_LINK “H”: link off, “L”: link on
76
UNI_SO
O
Sony-Bus serial data output to the bus interface
77
UNI_SI
I
Sony-Bus serial data input from the bus interface
78
UNI_CK
I
Sony-Bus serial clock input from the bus interface
79
NC
O
Not used. (Open)
80
SDA
I/O
I2C interface data input/output
81
SCL
O
I2C interface clock output
82
NC
O
Not used. (Open)
83
TSO
O
Serial data output to the servo IC
84
TSI
I
Serial data input from the servo IC
85
TSCK
O
Serial clock output to the servo IC
86
LEDDAT
O
LED data output for the jig
87
LEDCLK
O
LED clock output for the jig
88
LEDLAT
O
LED latch signal output for the jig
89, 90
NC
O
Not used. (Open)
91
BUSON
I
Sony-Bus BUS ON signal input from the bus interface
92
BUCHK
I
Back up power supply detection signal input
93
A-ATT
O
Audio muting control signal output
94
CDON
O
Power control signal output for the CD servo “H”: servo on, “L”: during loading
95
NC
O
Not used. (Open)
96
U/J_SEL
I
Destination setting pin
97
TEXTSEL
I
CD text function setting pin
98
NC
O
Not used. (Open)
99
CFSEL
I
Custom file function setting pin
100
DOUT SEL
I
Digital output selection setting pin “H”: digital output available
20
CDX-M850MP
• IC5 CXD9684R-005 (DSP) (SERVO Board (1/2))
Pin No.
Pin Name
I/O
Pin Description
1
/RESET
I
Reset input pin “L”: reset
2
MIMD
I
Microcomputer interface mode selection input “H”: I2C, “L”: TSB
3, 4
AD0, AD1
O
External SRAM address signal output
5
MIDIO (I2C_SDA)
I/O
Serial data input/output
6
MICK (I2C_SCL)
I
Serial clock input
7
AD2
O
External SRAM address signal output
8
VDDT (3.3V)
—
Power supply (3.3 V) for digital circuit
9
SDO
O
Data output
10, 11
AD3, AD4
O
External SRAM address signal output
12
SDI0
I
Data input 0
13
BCKIA
I
Bit clock input A
14
LRCKIA
I
LR clock input A
15
AD5
O
External SRAM address signal output
16
CE
O
External SRAM chip enable signal output
17
OE
O
External SRAM output enable signal output
18
VDD (2.5V)
—
Power supply pin (2.5 V) for digital circuit
19
STANDBY
I
Standby mode control signal input “H”: STB, “L”: normal
20
VSS (2.5VGND)
—
Ground pin for digital circuit
21
VSSL (2.5VGND)
—
Ground pin for DAC Lch
22
VRAL
—
Reference voltage pin for DAC Lch
23
LO
O
DAC Lch signal output (Open)
24
VDAL (2.5V)
—
Power supply pin (2.5 V) for DAC Lch
25
VDAR (2.5V)
—
Power supply pin (2.5 V) for DAC Rch
26
RO
O
DAC Rch signal output (Open)
27
VRAR
—
Reference voltage pin for DAC Rch
28
VSSR (2.5VGND)
—
Ground pin for DAC Rch
29
TESTP
I
Pin for test “H”: test mode, “L”: normal (fixed at “L”)
30
CKS
I
VCO selection input “H”: VCO, “L”: X1 input
31 – 34
AD12 to AD9
O
External SRAM address signal output
35
VDDT (3.3V)
—
Power supply pin (3.3 V) for digital circuit
36 – 38
AD8 to AD6
O
External SRAM address signal output
39
REQ
O
Interrupt request signal output to the CD master control
40
VSS
—
Ground pin for digital circuit
41, 42
AD13, AD14
O
External SRAM address signal output
43
WR
O
External SRAM write signal output
44, 45
AD16, AD15
O
External SRAM address signal output
46, 47
IO0, IO1
I/O
External SRAM data input/output
48
VSS
—
Ground pin for digital circuit
49 – 51
IO2 to IO4
I/O
External SRAM data input/output
52
VDD (2.5V)
—
Power supply pin (2.5 V) for digital circuit
53 – 55
IO5 to IO7
I/O
External SRAM data input/output
56
VSSP
—
Ground pin for VCO circuit
57
PDO
O
PLL phase error detection signal output
58
VCOI
I
VCO control voltage input
59
VDDP
—
Power supply pin for VCO circuit
60
XRDE
I/O
External clock input, audio clock output Not used. (Open)
61
VDDX (2.5V)
—
Power supply pin for oscillation circuit
62
XI
I
Resonator pin
63
XO
O
Resonator pin
64
VSSX
—
Ground pin for oscillation circuit
Click on the first or last page to see other CDX-M850MP service manuals if exist.