Sony CDX-GT575UE / CDX-GT575UI / CDX-GT575UP / CDX-GT625UI / CDX-GT627UV Service Manual ▷ View online
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
9
9
(E, Mexican and Indian models)
Ver. 1.1
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if the unit shares a common negative (–) lead for the right and
left speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if the unit shares a common negative (–) lead for the right and
left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker and amplifier are
connected correctly.
If speaker and amplifier are not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker and amplifier are
connected correctly.
English
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power input leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power input leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect the
unit directly to the battery.
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect the
unit directly to the battery.
Connection example (
)
Subwoofer Direct Connection (
-C)
For details on the setting for the connection, see the
supplied Operating Instruction.
supplied Operating Instruction.
* Do not connect a speaker in this connection.
Notes
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
amplifier.
The alarm will only sound if the built-in amplifier is used.
Español
Precauciones
Esta unidad ha sido diseñada para alimentarse sólo con
cc de 12 V de masa negativa.
No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los rieles del asiento).
Antes de realizar las conexiones, apague el automóvil
para evitar cortocircuitos.
Conecte los cables de fuente de alimentación amarillo y
rojo solamente después de haber conectado los demás.
Conecte todos los cables de conexión a masa a un
punto común.
Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
cc de 12 V de masa negativa.
No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los rieles del asiento).
Antes de realizar las conexiones, apague el automóvil
para evitar cortocircuitos.
Conecte los cables de fuente de alimentación amarillo y
rojo solamente después de haber conectado los demás.
Conecte todos los cables de conexión a masa a un
punto común.
Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
Notas sobre el cable de fuente de alimentación
(amarillo)
(amarillo)
Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
Si no hay circuitos del automóvil con capacidad nominal
suficientemente alta, conecte la unidad directamente a la
batería.
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
Si no hay circuitos del automóvil con capacidad nominal
suficientemente alta, conecte la unidad directamente a la
batería.
Ejemplo de conexiones (
)
Conexión directa de altavoz de subgraves (
-C)
Para obtener más información sobre cómo configurar la
conexión, consulte el Manual de instrucciones
suministrado.
conexión, consulte el Manual de instrucciones
suministrado.
*
No conecte un altavoz a esta conexión.
Notas
Asegúrese de conectar primero el cable de conexión a masa antes de
realizar la conexión del amplificador.
La alarma sonará únicamente si se utiliza el amplificador incorporado.
realizar la conexión del amplificador.
La alarma sonará únicamente si se utiliza el amplificador incorporado.
Connection diagram (
)
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow,
and red power supply leads.
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers and a power antenna (aerial).
Connecting any other system may damage the unit.
Connecting any other system may damage the unit.
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal surface of
the car first.
the car first.
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
in the accessory position of the ignition key
switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is energized
at all times
at all times
Be sure to connect the black ground (earth) lead to a metal surface of
the car first.
the car first.
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.
When your car has built-in FM/AM antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
the unit.
When your car has built-in FM/AM antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
When the yellow power input lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Diagrama de conexión (
)
A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después los
cables amarillo y rojo de fuente de alimentación.
cables amarillo y rojo de fuente de alimentación.
Al cable de control de la antena motorizada o al
cable de fuente de alimentación del amplificador
de señal de la antena
cable de fuente de alimentación del amplificador
de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplificador de señal
de la antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
de la antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
A AMP REMOTE IN de un amplificador de
potencia opcional
potencia opcional
Esta conexión es sólo para amplificadores y una antena motorizada.
La conexión de cualquier otro sistema puede dañar la unidad.
La conexión de cualquier otro sistema puede dañar la unidad.
A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa negro a
una superficie metálica del automóvil.
una superficie metálica del automóvil.
Al terminal de alimentación de +12 V que recibe
energía en la posición de accesorio del
interruptor de encendido
energía en la posición de accesorio del
interruptor de encendido
Notas
Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa negro
a una superficie metálica del automóvil.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa negro
a una superficie metálica del automóvil.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
Al terminal de alimentación de +12 V que recibe
energía sin interrupción
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa negro a
una superficie metálica del automóvil.
una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
El cable REM OUT (rayado azul y blanco) suministra cc +12 V al
encender la unidad.
Si el automóvil dispone de una antena de FM/AM incorporada en el
cristal trasero o lateral, conecte el cable REM OUT (rayado azul y
blanco) o el cable de fuente de alimentación auxiliar (rojo) al terminal
de alimentación del amplificador de señal de la antena existente. Para
obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin caja
de relé.
encender la unidad.
Si el automóvil dispone de una antena de FM/AM incorporada en el
cristal trasero o lateral, conecte el cable REM OUT (rayado azul y
blanco) o el cable de fuente de alimentación auxiliar (rojo) al terminal
de alimentación del amplificador de señal de la antena existente. Para
obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin caja
de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito de la
memoria recibirá siempre alimentación, aunque apague el interruptor de
encendido.
Si conecta el cable de fuente de alimentación amarillo, el circuito de la
memoria recibirá siempre alimentación, aunque apague el interruptor de
encendido.
Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de
potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil, ni conecte
los terminales del altavoz derecho con los del izquierdo.
No conecte el cable de conexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces activos (con
amplificadores incorporados) a los terminales de altavoz, puede dañar
la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un cable
negativo común (–) para los altavoces derecho e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de
potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil, ni conecte
los terminales del altavoz derecho con los del izquierdo.
No conecte el cable de conexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces activos (con
amplificadores incorporados) a los terminales de altavoz, puede dañar
la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un cable
negativo común (–) para los altavoces derecho e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de
ambos dispositivos.
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de
ambos dispositivos.
A
B
C
*
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no
suministrado)
Equipo utilizado en las ilustraciones (no
suministrado)
Front speaker
Altavoz frontal
Altavoz frontal
Subwoofer
Altavoz potenciador de graves
Altavoz potenciador de graves
Power amplifier
Amplificador de potencia
Amplificador de potencia
Rear speaker
Altavoz posterior
Altavoz posterior
REM OUT
Max. supply current 0.4 A
Corriente máx. de alimentación de 0,4 A
Corriente máx. de alimentación de 0,4 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Con rayas azules y blancas
Con rayas azules y blancas
Red
Rojo
Rojo
Orange/white striped
Con rayas naranjas y blancas
Con rayas naranjas y blancas
Yellow
Amarillo
Amarillo
White
Blanco
Blanco
Green
Verde
Verde
Purple
Morado
Morado
White/black striped
Con rayas blancas y negras
Con rayas blancas y negras
Gray/black striped
Con rayas grises y negras
Con rayas grises y negras
Green/black striped
Con rayas verdes y negras
Con rayas verdes y negras
Gray
Gris
Gris
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
ACC
ILLUMINATION
BATTERY
Black
Negro
Negro
Purple/black striped
Con rayas moradas y negras
Con rayas moradas y negras
*
2
*
2
*
1
from car antenna (aerial)
desde la antena del
automóvil
desde la antena del
automóvil
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
*
1
Impedancia de los altavoces: de 4 a 8 Ω × 4
*
2
Cable con terminales RCA (no suministrado).
*
3
AUDIO OUT (salida de audio) puede cambiarse a SUB o REAR.
Para obtener información, consulte el manual de instrucciones
suministrado.
suministrado.
*
4
Puede requerirse un adaptador independiente.
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
RCA pin cord (not supplied).
*
3
AUDIO OUT can be switched SUB or REAR. For details, see the
supplied Operating Instructions.
*
4
Separate adaptor may be required.
Fuse replacement (
)
When replacing the fuse, be sure to use one matching the
amperage rating stated on the original fuse. If the fuse
blows, check the power connection and replace the fuse. If
the fuse blows again after replacement, there may be an
internal malfunction. In such a case, consult your nearest
Sony dealer.
amperage rating stated on the original fuse. If the fuse
blows, check the power connection and replace the fuse. If
the fuse blows again after replacement, there may be an
internal malfunction. In such a case, consult your nearest
Sony dealer.
Notes on the tuning step
For how to set the tuning step, see the supplied
Operating Instructions.
If replacing the car battery or changing the connections,
the tuning step setting will be erased.
Operating Instructions.
If replacing the car battery or changing the connections,
the tuning step setting will be erased.
Sustitución del fusible (
)
Al sustituir el fusible, asegúrese de utilizar uno cuyo
amperaje coincida con el especificado en el original. Si el
fusible se funde, verifique la conexión de alimentación y
sustitúyalo. Si el fusible vuelve a fundirse después de
sustituirlo, es posible que exista alguna falla de
funcionamiento interno. En tal caso, consulte con el
distribuidor Sony más cercano.
amperaje coincida con el especificado en el original. Si el
fusible se funde, verifique la conexión de alimentación y
sustitúyalo. Si el fusible vuelve a fundirse después de
sustituirlo, es posible que exista alguna falla de
funcionamiento interno. En tal caso, consulte con el
distribuidor Sony más cercano.
Notas acerca de la
sintonización
sintonización
Para obtener información sobre cómo ajustar la
sintonización, consulte el manual de instrucciones
suministrado.
Si se reemplaza la batería del auto o se cambian las
conecciones, la configuración de la sintonización se
borrará.
sintonización, consulte el manual de instrucciones
suministrado.
Si se reemplaza la batería del auto o se cambian las
conecciones, la configuración de la sintonización se
borrará.
Mounting the unit in a
Japanese car (
Japanese car (
)
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws
To prevent malfunction, install only with the supplied screws
.
How to detach and attach the
front panel (
front panel (
)
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press and hold
. Press the front panel release button, and
pull it off towards you.
-B To attach
Engage part
of the front panel with part
of the unit,
as illustrated, and push the left side into position until it
clicks.
clicks.
Warning if your car’s ignition
has no ACC position
has no ACC position
Be sure to set the Auto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents battery
drain.
If you do not set the Auto Off function, press and hold
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents battery
drain.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
Montaje de la unidad en un
automóvil japonés (
automóvil japonés (
)
Es posible que no pueda instalar esta unidad en algunos
automóviles japoneses. En tal caso, consulte a su
distribuidor Sony.
automóviles japoneses. En tal caso, consulte a su
distribuidor Sony.
Nota
Para evitar que se produzcan fallas de funcionamiento, realice la
instalación solamente con los tornillos suministrados
Para evitar que se produzcan fallas de funcionamiento, realice la
instalación solamente con los tornillos suministrados
.
Forma de extraer e instalar el
panel frontal (
panel frontal (
)
Antes de instalar la unidad, extraiga el panel frontal.
-A Para extraerlo
Antes de extraer el panel frontal, asegúrese de mantener
presionado
presionado
. Presione el botón de
liberación del panel frontal y extraiga el panel frontal hacia
usted.
usted.
-B Para instalarlo
Coloque la parte
del panel frontal en la parte
de la
unidad, como se muestra en la ilustración, y después
presione la parte izquierda hasta que encaje.
presione la parte izquierda hasta que encaje.
Advertencia: si el encendido
del automóvil no dispone de
una posición ACC
del automóvil no dispone de
una posición ACC
Asegúrese de ajustar la función de desconexión
automática. Para obtener más información, consulte el
manual de instrucciones suministrado.
La unidad se apagará completa y automáticamente en el
tiempo establecido después de que se desconecte la
unidad, lo que evita que se desgaste la batería.
Si no ha ajustado la función de desconexión automática,
mantenga presionado
automática. Para obtener más información, consulte el
manual de instrucciones suministrado.
La unidad se apagará completa y automáticamente en el
tiempo establecido después de que se desconecte la
unidad, lo que evita que se desgaste la batería.
Si no ha ajustado la función de desconexión automática,
mantenga presionado
cada vez que
apague el interruptor de encendido, hasta que la pantalla
desaparezca.
desaparezca.
Español
Precauciones
Elija cuidadosamente el lugar de montaje de forma que
la unidad no interfiera con las funciones normales de
conducción.
Evite instalar la unidad donde pueda quedar expuesta a
polvo, suciedad, vibraciones excesivas o altas
temperaturas, por ejemplo, a la luz solar directa o cerca
de conductos de calefacción.
Para realizar una instalación segura y firme, utilice
solamente elementos de instalación suministrados.
la unidad no interfiera con las funciones normales de
conducción.
Evite instalar la unidad donde pueda quedar expuesta a
polvo, suciedad, vibraciones excesivas o altas
temperaturas, por ejemplo, a la luz solar directa o cerca
de conductos de calefacción.
Para realizar una instalación segura y firme, utilice
solamente elementos de instalación suministrados.
Ajuste del ángulo de montaje
Ajuste el ángulo de montaje a menos de 45°.
Extracción del marco de
protección y del soporte (
protección y del soporte (
)
Antes de instalar la unidad, retire el marco de
protección
protección
y el soporte
de la misma.
1
Retire el marco de protección
.
Apriete ambos bordes del marco de protección
y, a continuación, tire de él hacia fuera.
2
Retire el soporte
.
Inserte ambas llaves de liberación
entre la
unidad y el soporte
hasta que encajen.
Presione el soporte
y, a continuación,
levante la unidad para separar ambos
elementos.
elementos.
Ejemplo de montaje (
)
Instalación en el tablero
Notas
Antes de instalar la unidad, compruebe que los enganches de ambos
lados del soporte
lados del soporte
estén doblados hacia adentro 2 mm. Si no lo están
o están doblados hacia afuera, la unidad no se instalará correctamente
y puede saltar
y puede saltar
( -1).
Si es necesario, doble las uñas hacia fuera para que encaje firmemente
( -2).
Compruebe que los 4 enganches del marco de protección
Compruebe que los 4 enganches del marco de protección
estén bien
fijados en las ranuras de la unidad
( -3).
English
Precautions
Choose the installation location carefully so that the unit
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection
collar and the bracket (
collar and the bracket (
)
Before installing the unit, remove the protection
collar
collar
and the bracket
from the unit.
1
Remove the protection collar
.
Pinch both edges of the protection collar
, then
pull it out.
2
Remove the bracket
.
Insert both release keys
together between
the unit and the bracket
until they click.
Pull down the bracket
, then pull up the unit
to separate.
Mounting example (
)
Installation in the dashboard
Notes
Before installing, make sure that the catches on both sides of the
bracket
bracket
are bent inwards 2 mm (
3
/
32
in). If the catches are straight or
bent outwards, the unit will not be installed securely and may spring
out
out
( -1).
Bend these claws outward for a tight fit, if necessary
( -2).
Make sure that the 4 catches on the protection collar
are properly
engaged in the slots of the unit
( -3).
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
A
TOYOTA
B
NISSAN
to dashboard/center console
al tablero o consola central
al tablero o consola central
to dashboard/center console
al tablero o consola central
al tablero o consola central
Existing parts supplied with your car
Piezas existentes suministradas con su
automóvil
Piezas existentes suministradas con su
automóvil
Existing parts supplied with your car
Piezas existentes suministradas con su
automóvil
Piezas existentes suministradas con su
automóvil
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
tamaño
5 × 8 mm máx.
5 × 8 mm máx.
1
2
Face the hook inwards.
El gancho debe encontrarse
en la parte interior.
El gancho debe encontrarse
en la parte interior.
2
3
Dashboard
Tablero
Tablero
Fire wall
Cortafuegos
Cortafuegos
Claws
Uñas
Uñas
1
Catch
Enganche
Enganche
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
A
B
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Front panel release button
Botón de liberación del panel frontal
Botón de liberación del panel frontal
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
10
10
(Saudi Arabia model)
Ver. 1.1
(
)
ﻞﻴﺻﻮﺘﻟا ﻂﻄﺨﻣ
ةرﺎﻴﺴﻟا ﻦﻣ ﻲﻧﺪﻌﻣ ﺢﻄﺳ ﻰﻟإ
ﺮﻔﺻﻷا ﺔﻗﺎﻄﻟا داﺪﻣإ كﻼﺳأ ﻞﻴﺻﻮﺘﺑ ﻢﻗ ﻢﺛ ،دﻮﺳﻷا ﺾﻳرﺄﺘﻟا ﻚﻠﺳ ﻞﻴﺻﻮﺘﺑ ًﻻوأ ﻢﻗ
.ﺮﻤﺣﻷاو
ﻢﺨﻀﻤﻟ ﺔﻗﺎﻄﻟا داﺪﻣإ ﻚﻠﺳ وأ ﻲﻟﻵا ﻲﺋاﻮﻬﻟﺎﺑ ﻢﻜﺤﺘﻟا ﻚﻠﺳ ﻰﻟإ
ﻲﺋاﻮﻬﻟا ﻢﺨﻀﻣ زﺰﻌﻣ ﻲﻓ ﺐﻛﺮﻤﻟا تﻮﺼﻟا
تﺎﻈﺣﻼﻣ
زﺰﻌﻣ وأ ﻲﻟآ ﻲﺋاﻮﻫ دﻮﺟو مﺪﻋ ﺔﻟﺎﺣ ﻲﻓ ﻚﻠﺴﻟا اﺬﻫ ﻞﻴﺻﻮﺗ يروﺮﻀﻟا ﻦﻣ ﺲﻴﻟ
.ﺎًﻳوﺪﻳ ﻪﻠﻴﻐﺸﺗ ﻢﺘﻳ ﻲﺑﻮﻜﺴﻠﺗ ﻲﺋاﻮﻫ دﻮﺟو ﺪﻨﻋ وأ ﻲﺋاﻮﻫ
جﺎﺟﺰﻟا ﻲﻓ ﺐﻛﺮﻣ ﻲﻠﺧاد
FM/MW/SW
ﻲﺋاﻮﻬﺑ ةﺰﻬﺠﻣ ﻚﺗرﺎﻴﺳ نﻮﻜﺗ ﺎﻣﺪﻨﻋ
.«ﺔﻗﺎﻄﻟا داﺪﻣإو ﻢﻜﺤﺘﻟا كﻼﺳأ لﻮﺣ تﺎﻈﺣﻼﻣ» ﻊﺟار ،ﻲﺒﻧﺎﺠﻟا /ﻲﻔﻠﺨﻟا
تﻮﺼﻟا ﻢﺨﻀﻣ ﻰﻠﻋ
AMP REMOTE IN
ﻞﻴﺻﻮﺘﻟا فﺮﻃ ﻰﻟإ
يرﺎﻴﺘﺧﻻا ﻂﺸﻨﻟا
يأ ﻞﻴﺻﻮﺘﺑ مﺎﻴﻘﻟا .ﻲﻟﻵا ﻲﺋاﻮﻬﻟاو تﻮﺼﻟا تﺎﻤﺨﻀﻤﻟ ﻂﻘﻓ ﺔﺼﺼﺨﻣ ﺔﻠﺻﻮﻟا هﺬﻫ
.زﺎﻬﺠﻟا ﻒﻠﺘﻳ ﺪﻗ ﺮﺧآ مﺎﻈﻧ
ةرﺎﻴﺴﻟا ةءﺎﺿإ ةرﺎﺷإ
ﻰﻟإ
.ًﻻوأ ةرﺎﻴﺴﻟا ﻦﻣ ﻲﻧﺪﻌﻤﻟا ﺢﻄﺴﻟا ﻰﻟإ دﻮﺳﻷا ﺾﻳرﺄﺘﻟا ﻚﻠﺳ ﻞﻴﺻﻮﺗ ﻦﻣ ﺪﻛﺄﺗ
ﺎﻣﺪﻨﻋ رﺎﻴﺘﻟا ﻪﻴﻓ يﺮﺴﻳ يﺬﻟا ﻂﻟﻮﻓ
+12
ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ فﺮﻃ ﻰﻟإ
تﺎﻴﻟﺎﻤﻜﻟا ﻊﺿﻮﻣ ﻲﻓ كﺮﺤﻤﻟا لﺎﻌﺷإ حﺎﺘﻔﻣ نﻮﻜﻳ
تﺎﻈﺣﻼﻣ
ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ فﺮﻃ ﻰﻟإ ﻞﻴﺻﻮﺘﻟﺎﺑ ﻢﻗ ،تﺎﻴﻟﺎﻤﻜﻟا ﻊﺿﻮﻣ دﻮﺟو مﺪﻋ ﺔﻟﺎﺣ ﻲﻓ
ﻚﻠﺳ ﻞﻴﺻﻮﺗ ﻦﻣ ﺪﻛﺄﺗ .ﺎًﻤﺋاد رﺎﻴﺘﻟا ﻪﻴﻓ يﺮﺴﻳ يﺬﻟا ﻂﻟﻮﻓ
+12
(ﺔﻳرﺎﻄﺑ)
.ًﻻوأ ةرﺎﻴﺴﻟا ﻦﻣ ﻲﻧﺪﻌﻤﻟا ﺢﻄﺴﻟا ﻰﻟإ دﻮﺳﻷا ﺾﻳرﺄﺘﻟا
جﺎﺟﺰﻟا ﻲﻓ ﺐﻛﺮﻣ ﻲﻠﺧاد
FM/MW/SW
ﻲﺋاﻮﻬﺑ ةﺰﻬﺠﻣ ﻚﺗرﺎﻴﺳ نﻮﻜﺗ ﺎﻣﺪﻨﻋ
.«ﺔﻗﺎﻄﻟا داﺪﻣإو ﻢﻜﺤﺘﻟا كﻼﺳأ لﻮﺣ تﺎﻈﺣﻼﻣ» ﻊﺟار ،ﻲﺒﻧﺎﺠﻟا /ﻲﻔﻠﺨﻟا
ﺎًﻤﺋاد رﺎﻴﺘﻟا ﻪﻴﻓ يﺮﺴﻳ يﺬﻟا ﻂﻟﻮﻓ
+12
ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ فﺮﻃ ﻰﻟإ
.ًﻻوأ ةرﺎﻴﺴﻟا ﻦﻣ ﻲﻧﺪﻌﻤﻟا ﺢﻄﺴﻟا ﻰﻟإ دﻮﺳﻷا ﺾﻳرﺄﺘﻟا ﻚﻠﺳ ﻞﻴﺻﻮﺗ ﻦﻣ ﺪﻛﺄﺗ
ﺔﻗﺎﻄﻟا داﺪﻣإو ﻢﻜﺤﺘﻟا كﻼﺳأ لﻮﺣ تﺎﻈﺣﻼﻣ
ﺎﻣﺪﻨﻋ ﻂﻟﻮﻓ
+12
ﺮﺷﺎﺒﻣ رﺎﻴﺗ داﺪﻣﺈﺑ مﻮﻘﻳ (ﺾﻴﺑأ/قرزأ ﻂﻄﺨﻣ)
REM OUT
ﻚﻠﺳ
ةﺪﺣﻮﻟا ﻞﻴﻐﺸﺘﺑ مﻮﻘﺗ
/ﻲﻔﻠﺨﻟا جﺎﺟﺰﻟا ﻲﻓ ﺐﻛﺮﻣ ﻲﻠﺧاد
FM/MW/SW
ﻲﺋاﻮﻬﺑ ةﺰﻬﺠﻣ ﻚﺗرﺎﻴﺳ نﻮﻜﺗ ﺎﻣﺪﻨﻋ
ﺔﻗﺎﻄﻟا داﺪﻣإ ﻚﻠﺳ وأ (ﺾﻴﺑأ/قرزأ ﻂﻄﺨﻣ)
REM OUT
ﻚﻠﺳ ﻞﻴﺻﻮﺘﺑ ﻢﻗ ،ﻲﺒﻧﺎﺠﻟا
لﻮﺼﺤﻠﻟ .ًﻼﺻأ دﻮﺟﻮﻤﻟا ﻲﺋاﻮﻬﻟا زﺰﻌﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ فﺮﻃ ﻰﻟإ (ﺮﻤﺣأ) ﺔﻴﻟﺎﻤﻜﻠﻟ
.ﻞﻴﻛﻮﻟا ﺮﺸﺘﺳا ،ﻞﻴﺻﺎﻔﺗ ﻰﻠﻋ
.زﺎﻬﺠﻟا اﺬﻫ ﻲﻓ ﺔﺑوﺎﻨﻣ قوﺪﻨﺻ ﻰﻠﻋ يﻮﺘﺤﻳ ﻻ يﺬﻟا ﻲﻟﻵا ﻲﺋاﻮﻬﻟا لﺎﻤﻌﺘﺳا ﻦﻜﻤﻳ ﻻ
ةﺮﻛاﺬﻟا ﻆﻔﺣ ﻞﻴﺻﻮﺗ
ﻰﺘﺣ ﺎ ًﻀﻳأ ةﺮﻛاﺬﻟا ةﺮﺋاد ﻰﻟإ ﺔﻗﺎﻄﻟا داﺪﻣإ ﻢﺘﻴﺳ ،ﺮﻔﺻﻷا ﺔﻗﺎﻄﻟا ﻞﺧد ﻚﻠﺳ ﻞﻴﺻﻮﺗ ﺪﻨﻋ
.فﺎﻘﻳﻹا ﻊﺿو ﻲﻓ كﺮﺤﻤﻟا لﺎﻌﺷإ حﺎﺘﻔﻣ نﻮﻜﻳ ﺎﻣﺪﻨﻋ
ﺔﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ لﻮﺣ تﺎﻈﺣﻼﻣ
.زﺎﻬﺠﻟا ﺊﻔﻃأ ،تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ ﻞﺒﻗ
ةرﺪﻘﻟا ﻊﻣ ﻞﻣﺎﻌﺘﻟا ﻰﻠﻋ ةءﻮﻔﻛ تﺎﻴﻠﺑﺎﻗو ،موأ
8
ﻰﻟإ
4
ﺔﻗوﺎﻌﻤﺑ تﺎﻋﺎﻤﺳ ﻞﻤﻌﺘﺳا
.ﻒﻠﺘﻠﻟ ﺎﻬﺿﺮﻌﺗ يدﺎﻔﺘﻟ
فاﺮﻃأ ﻞﻴﺻﻮﺗ وأ ،ةرﺎﻴﺴﻟا ﻞﻜﻴﻫ ﻰﻟإ تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ فاﺮﻃأ ﻞﻴﺻﻮﺘﺑ ﻢﻘﺗ ﻻ
.ىﺮﺴﻴﻟا تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ فاﺮﻃﺄﺑ ﻰﻨﻤﻴﻟا تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ
.ﺔﻋﺎﻤﺴﻠﻟ (
–
) ﺐﻟﺎﺴﻟا ﻞﻴﺻﻮﺘﻟا فﺮﻃ ﻰﻟإ زﺎﻬﺠﻟا اﺬﻫ ﺾﻳرﺄﺗ ﻚﻠﺳ ﻞﻴﺻﻮﺘﺑ ﻢﻘﺗ ﻻ
.يزاﻮﺘﻟا ﻰﻠﻋ تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ لوﺎﺤﺗ ﻻ
تﺎﻤﺨﻀﻤﺑ) ﺔﻄﺸﻧ تﺎﻋﺎﻤﺳ ﻞﻴﺻﻮﺘﺑ مﺎﻴﻘﻟا .ﻂﻘﻓ ﺔﻟﺎﻌﻓ ﺮﻴﻏ تﺎﻋﺎﻤﺳ ﻞﻴﺻﻮﺘﺑ ﻢﻗ
.زﺎﻬﺠﻟا ﻒﻠﺗ ﻰﻟإ يدﺆﻳ ﺪﻗ تﺎﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ فاﺮﻃأ ﻰﻟإ (ﺔﻴﻠﺧاد تﻮﺻ
اذإ ﻚﺗرﺎﻴﺳ ﻲﻓ ﺔﺒﻛﺮﻤﻟا ﺔﻴﻠﺧاﺪﻟا ﺔﻋﺎﻤﺴﻟا كﻼﺳأ ﻞﻤﻌﺘﺴﺗ ﻻ ،ﻞﻠﺧ ثوﺪﺣ يدﺎﻔﺘﻟ
.ىﺮﺴﻴﻟاو ﻰﻨﻤﻴﻟا تﺎﻋﺎﻤﺴﻠﻟ كﺮﺘﺸﻣ (
–
) ﺐﻟﺎﺳ ﻚﻠﺳ ﻰﻠﻋ يﻮﺘﺤﻳ زﺎﻬﺠﻟا نﺎﻛ
.ﺾﻌﺒﻟا ﺎﻬﻀﻌﺒﺑ زﺎﻬﺠﻟا ﺔﻋﺎﻤﺳ كﻼﺳأ ﻞﻴﺻﻮﺘﺑ ﻢﻘﺗ ﻻ
ﻞﻴﺻﻮﺘﻟا لﻮﺣ ﺔﻈﺣﻼﻣ
ﻲﻓ
"FAILURE"
ضﺮﻋ ﻢﺘﻴﻓ ،ﺢﻴﺤﺻ ﻞﻜﺸﺑ تﻮﺼﻟا ﻢﺨﻀﻣو ﺔﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ ﻢﺘﻳ ﻢﻟ اذإ
.ﺢﻴﺤﺻ ﻞﻜﺸﺑ تﻮﺼﻟا ﻢﺨﻀﻣو ﺔﻋﺎﻤﺴﻟا ﻞﻴﺻﻮﺗ ﻦﻣ ﺪﻛﺄﺗ ،ﺔﻟﺎﺤﻟا هﺬﻫ ﻲﻓ .ﺔﺷﺎﺸﻟا
English
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power input leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power input leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect the
unit directly to the battery.
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect the
unit directly to the battery.
Connection example (
)
Subwoofer Direct Connection (
-C)
For details on the setting for the connection, see the
supplied Operating Instruction.
supplied Operating Instruction.
*
Do not connect a speaker in this connection.
Notes
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
amplifier.
The alarm will only sound if the built-in amplifier is used.
ﺔﻴﺑﺮﻌﻟا ﺔﻐﻠﻟا
تﺎﻬﻴﺒﻨﺗ
ﺐﻟﺎﺳ ﺾﻳرﺄﺘﺑ ﻂﻟﻮﻓ
12
ﺮﺷﺎﺒﻣ رﺎﻴﺘﺑ ﻞﻴﻐﺸﺘﻠﻟ ﺔﻤﻤﺼﻣ ةﺪﺣﻮﻟا هﺬﻫ
.ﻂﻘﻓ
ﻰﻠﻋ) ﺔﻛﺮﺤﺘﻤﻟا ءاﺰﺟﻷا ﺲﻣﻼﺗ وأ ،ﻲﻏﺮﺑ ﺖﺤﺗ ﻦﻣ ﺮﻤﺗ كﻼﺳﻷا عﺪﺗ ﻻ
.(ﺪﻌﻘﻤﻟا ﻚﻳﺮﺤﺗ نﺎﺒﻀﻗ ،لﺎﺜﻤﻟا ﻞﻴﺒﺳ
ثوﺪﺣ يدﺎﻔﺘﻟ كﺮﺤﻤﻟا لﺎﻌﺷإ حﺎﺘﻔﻣ ﺊﻔﻃأ ،تﻼﻴﺻﻮﺘﻟا ﺬﻴﻔﻨﺗ ﻞﺒﻗ
.ﻲﺋﺎﺑﺮﻬﻛ سﺎﻤﺗ
ﻦﻣ ءﺎﻬﺘﻧﻻا ﺪﻌﺑ ﻂﻘﻓ ﺮﻤﺣﻷاو ﺮﻔﺻﻷا ﺔﻗﺎﻄﻟا ﻞﺧد كﻼﺳأ ﻞﻴﺻﻮﺘﺑ ﻢﻗ
.ىﺮﺧﻷا كﻼﺳﻷا ﻞﻴﺻﻮﺗ
.ﺔﻛﺮﺘﺸﻣ ﺾﻳرﺄﺗ ﺔﻄﻘﻧ ﻰﻟإ ﺾﻳرﺄﺘﻟا كﻼﺳأ ﻊﻴﻤﺟ ﺮﻳﺮﻤﺘﺑ ﻢﻗ
ﻂﻳﺮﺷ لﺎﻤﻌﺘﺳﺎﺑ ﺔﻟﻮﺻﻮﻤﻟا ﺮﻴﻏ كﻼﺳﻷا ﻲﻓ ءﺎﺨﺗرا يأ لﺰﻋ ﻦﻣ ﺪﻛﺄﺗ
.ﺔﻣﻼﺴﻟا نﺎﻤﻀﻟ ﻲﺋﺎﺑﺮﻬﻛ
(ﺮﻔﺻأ) ﺔﻗﺎﻄﻟا داﺪﻣإ ﻚﻠﺳ لﻮﺣ تﺎﻈﺣﻼﻣ
نأ ﺐﺠﻳ ،ىﺮﺧأ ﻮﻳﺮﻴﺘﺳ تﺎﻧﻮﻜﻣ ﻊﻣ كاﺮﺘﺷﻻﺎﺑ ةﺪﺣﻮﻟا هﺬﻫ ﻞﻴﺻﻮﺗ ﺪﻨﻋ
ﻦﻣ زﻮﻴﻓ ﻞﻛ راﺪﻘﻣ ﻦﻣ ﻰﻠﻋأ ﺔﻟﻮﺻﻮﻤﻟا ةرﺎﻴﺴﻟا ةﺮﺋاد ةﺮﻳﺎﻌﻣ نﻮﻜﺗ
.تﺎﻧﻮﻜﻤﻟا تازﻮﻴﻓ
،ﺔﻳﺎﻔﻜﻟا ﻪﻴﻓ ﺎﻤﺑ ﻊﻔﺗﺮﻣ راﺪﻘﻤﺑ ةﺮﻳﺎﻌﻣ ةرﺎﻴﺴﻟا ﻲﻓ ﺮﺋاود ﺪﺟﻮﺗ ﻻ ﺎﻣﺪﻨﻋ
.ةﺮﺷﺎﺒﻣ ﺔﻳرﺎﻄﺒﻟا ﻰﻟإ زﺎﻬﺠﻟا ﻞﻴﺻﻮﺘﺑ ﻢﻗ
(
)
ﻞﻴﺻﻮﺘﻟا لﺎﺜﻣ
(
-C)
تﻮﺼﻟا ﻢﺨﻀﻤﻟ ةﺮﺷﺎﺒﻤﻟا ﺔﻠﺻﻮﻟا
ﻞﻴﻐﺸﺘﻟا تﺎﻤﻴﻠﻌﺗ ﺮﻈﻧا ،ﺔﻠﺻﻮﻟا داﺪﻋإ لﻮﺣ ﻞﻴﺻﺎﻔﺗ ﻰﻠﻋ لﻮﺼﺤﻠﻟ
.ﺔﻘﻓﺮﻤﻟا
.ﺔﻠﺻﻮﻟا هﺬﻫ ﻲﻓ ﺔﻋﺎﻤﺳ ﺔﻳأ ﻞﻴﺻﻮﺘﺑ ﻢﻘﺗ ﻻ
*
تﺎﻈﺣﻼﻣ
.تﻮﺼﻟا ﻢﺨﻀﻣ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﺾﻳرﺄﺘﻟا ﻚﻠﺳ ﻞﻴﺻﻮﺗ ﻦﻣ ﺪﻛﺄﺗ
.ﻲﻠﺧاﺪﻟا تﻮﺼﻟا ﻢﺨﻀﻣ لﺎﻤﻌﺘﺳا ﻢﺗ اذإ ﻂﻘﻓ راﺬﻧإ تﻮﺻ رﺪﺼﻴﺳ
Connection diagram (
)
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow,
and red power supply leads.
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
When your car has a built-in FM/MW/SW antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply leads.”
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
When your car has a built-in FM/MW/SW antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers and a power antenna (aerial).
Connecting any other system may damage the unit.
Connecting any other system may damage the unit.
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
of the car first.
To the +12 V power terminal which is energized in
the accessory position of the ignition key switch
the accessory position of the ignition key switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
When your car has a built-in FM/MW/SW antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply leads.”
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
When your car has a built-in FM/MW/SW antenna (aerial) in the
rear/side glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is energized
at all times
at all times
Be sure to connect the black ground (earth) lead to a metal surface of
the car first.
the car first.
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.
When your car has built-in FM/MW/SW antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
the unit.
When your car has built-in FM/MW/SW antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
When the yellow power input lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if the unit shares a common negative (–) lead for the right and
left speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if the unit shares a common negative (–) lead for the right and
left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker and amplifier are
connected correctly.
If speaker and amplifier are not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker and amplifier are
connected correctly.
(
)
لﺎﺼﺗا رادﻮﻤﻧ
ﻞﯿﺒﻣﻮﺗا یﺰﻠﻓ ﺢﻄﺳ ﮏﯾ ﻪﺑ
ﻞﺻو ار ﺰﻣﺮﻗ و درز ﻊﺒﻨﻣ یﺎﻫ ﻢﯿﺳ ﺲﭙﺳ ،ﺪﯿﻨﮐ ﻞﺻو ار ﻦﯿﻣز هﺎﯿﺳ ﻢﯿﺳ اﺪﺘﺑا
.ﺪﯿﻨﮐ
ﺮﯾﺎﻓ ﯽﻠﭙﻣآ قﺮﺑ ﻊﺒﻨﻣ ﻢﯿﺳ ﺎﯾ ﯽﻗﺮﺑ ﯽﯾاﻮﻫ ﻦﺘﻧآ لﺮﺘﻨﮐ ﻢﯿﺳ ﻪﺑ
ﯽﯾاﻮﻫ ﻦﺘﻧآ هﺪﻨﻨﮐ ﺖﯾﻮﻘﺗ
تﺎﮑﻧ
،دراﺪﻧ دﻮﺟو ﯽﯾاﻮﻫ ﻦﺘﻧآ هﺪﻨﻨﮐ ﺖﯾﻮﻘﺗ ﺎﯾ ﯽﻗﺮﺑ ﯽﯾاﻮﻫ ﻦﺘﻧآ ﻪﮐ ﯽﺗرﻮﺻ رد
.ﺖﺴﯿﻧ یروﺮﺿ ﻢﯿﺳ ﻦﯾا ندﺮﮐ ﻞﺻو
ﻪﺸﯿﺷ رد
FM/MW/SW
ﯽﯾاﻮﻫ ﻦﺘﻧآ ﮏﯾ یاراد ﺎﻤﺷ ﻞﯿﺒﻣﻮﺗا ﻪﮐ ﯽﻣﺎﮕﻨﻫ
ار "قﺮﺑ ﻊﺒﻨﻣ و لﺮﺘﻨﮐ یﺎﻫ ﻢﯿﺳ درﻮﻣ رد تﺎﮑﻧ" ،ﺪﺷﺎﺑ ﯽﻣ یرﺎﻨﮐ/ﯽﺒﻘﻋ
.ﺪﯿﯾﺎﻤﻧ ﻪﻈﺣﻼﻣ
یرﺎﯿﺘﺧا ﯽﻗﺮﺑ ﺮﯾﺎﻓ ﯽﻠﭙﻣآ ﮏﯾ
AMP REMOTE IN
ﻪﺑ
ﻢﺘﺴﯿﺳ ﺮﻫ لﺎﺼﺗا .ﺖﺳا یﻮﻗ ﻦﺘﻧآ ﮏﯾ و ﺎﻫﺮﯾﺎﻓ ﯽﻠﭙﻣآ یاﺮﺑ ﺎﻬﻨﺗ لﺎﺼﺗا ﻦﯾا
.دﻮﺷ هﺎﮕﺘﺳد ﻪﺑ ﻪﻣﺪﺻ ﺚﻋﺎﺑ ﺪﻧاﻮﺗ ﯽﻣ یﺮﮕﯾد
ﻞﯿﺒﻣﻮﺗا غاﺮﭼ لﺎﻨﮕﯿﺳ
یاﺮﺑ
ﻞﯿﺒﻣﻮﺗا زا یﺰﻠﻓ ﺢﻄﺳ ﮏﯾ ﻪﺑ (ﻦﯿﻣز) ﯽﮑﺸﻣ ﯽﻨﯿﻣز ﻢﯿﺳ ﺪﯾﻮﺷ ﻦﺌﻤﻄﻣ اﺪﺘﺑا
.ﺪﺷﺎﺑ ﻞﺻو
ﭻﯿﯾﻮﺳ ﺪﯿﻠﮐ ﯽﺒﻧﺎﺟ ﺖﯿﻌﻗﻮﻣ رد ﻪﮐ ﺖﻟو
+12
قﺮﺑ لﺎﻨﯿﻣﺮﺗ ﻪﺑ
دﺮﯿﮔ ﯽﻣ وﺮﯿﻧ ترﺎﺘﺳا
تﺎﮑﻧ
ﻪﮐ ﺖﻟو
+12
(یﺮﺗﺎﺑ) قﺮﺑ لﺎﻨﯿﻣﺮﺗ ﻪﺑ ،دراﺪﻧ دﻮﺟو ﯽﺒﻧﺎﺟ ﺖﯿﻌﻗﻮﻣ ﭻﯿﻫ ﺮﮔا
یﺰﻠﻓ ﺢﻄﺳ ﻪﺑ ار ﻦﯿﻣز هﺎﯿﺳ ﻢﯿﺳ اﺪﺘﺑا ﺎﻤﺘﺣ .ﺪﯿﻨﮐ ﻞﺻو دﺮﯿﮔ ﯽﻣ وﺮﯿﻧ هراﻮﻤﻫ
.ﺪﯿﻨﮐ ﻞﺻو ﻞﯿﺒﻣﻮﺗا
ﻪﺸﯿﺷ رد
FM/MW/SW
ﯽﯾاﻮﻫ ﻦﺘﻧآ ﮏﯾ یاراد ﺎﻤﺷ ﻞﯿﺒﻣﻮﺗا ﻪﮐ ﯽﻣﺎﮕﻨﻫ
ار "قﺮﺑ ﻊﺒﻨﻣ و لﺮﺘﻨﮐ یﺎﻫ ﻢﯿﺳ درﻮﻣ رد ﯽﺗﺎﮑﻧ" ،ﺪﺷﺎﺑ ﯽﻣ یرﺎﻨﮐ/ﯽﺒﻘﻋ
.ﺪﯿﯾﺎﻤﻧ ﻪﻈﺣﻼﻣ
دﺮﯿﮔ ﯽﻣ وﺮﯿﻧ هراﻮﻤﻫ ﻪﮐ ﺖﻟو
+12
قﺮﺑ لﺎﻨﯿﻣﺮﺗ ﻪﺑ
.ﺪﯿﻨﮐ ﻞﺻو ﻞﯿﺒﻣﻮﺗا یﺰﻠﻓ ﺢﻄﺳ ﻪﺑ ار ﻦﯿﻣز هﺎﯿﺳ ﻢﯿﺳ اﺪﺘﺑا ﺎﻤﺘﺣ
قﺮﺑ ﻊﺒﻨﻣ و لﺮﺘﻨﮐ یﺎﻫ ﻢﯿﺳ درﻮﻣ رد ﯽﺗﺎﮑﻧ
+12
ﻢﯿﻘﺘﺴﻣ قﺮﺑ (هار هار ﺪﯿﻔﺳ/ﯽﺑآ)
REM OUT
ﻢﯿﺳ ،هﺎﮕﺘﺳد ندﺮﮐ ﻦﺷور مﺎﮕﻨﻫ
.ﺪﻨﮐ ﯽﻣ ﺪﯿﻟﻮﺗ ار
/ﯽﺒﻘﻋ ﻪﺸﯿﺷ رد
FM/MW/SW
ﯽﯾاﻮﻫ ﻦﺘﻧآ ﮏﯾ یاراد ﺎﻤﺷ ﻞﯿﺒﻣﻮﺗا ﻪﮐ ﯽﻣﺎﮕﻨﻫ
ار (ﺰﻣﺮﻗ) ﯽﺒﻧﺎﺟ قﺮﺑ ﻊﺒﻨﻣ ﻢﯿﺳ ﺎﯾ (هار هار ﺪﯿﻔﺳ/ﯽﺑآ)
REM OUT
ﻢﯿﺳ ،ﺖﺳا یرﺎﻨﮐ
هﺪﻨﺷوﺮﻓ ﺎﺑ تﺎﯿﺋﺰﺟ یاﺮﺑ .ﺪﯿﻨﮐ ﻞﺼﺘﻣ دﻮﺟﻮﻣ ﻦﺘﻧآ هﺪﻨﻨﮐ ﺖﯾﻮﻘﺗ قﺮﺑ لﺎﻨﯿﻣﺮﺗ ﻪﺑ
.ﺪﯿﯾﺎﻤﻧ ترﻮﺸﻣ دﻮﺧ
هدﺎﻔﺘﺳا درﻮﻣ هﺎﮕﺘﺳد ﻦﯾا ﺎﺑ ﺪﻧاﻮﺗ ﯽﻤﻧ ﺖﯾﻮﻘﺗ هﺎﮕﺘﺴﯾا ﮏﯾ نوﺪﺑ ﯽﯾاﻮﻫ ﻦﺘﻧآ ﮏﯾ
.دﺮﯿﮔ راﺮﻗ
ﻪﻈﻓﺎﺣ ﻆﻔﺣ لﺎﺼﺗا
ﯽﻣ هداد ﻪﻈﻓﺎﺣ راﺪﻣ ﻪﺑ هراﻮﻤﻫ قﺮﺑ .ﺖﺳا هﺪﺷ ﻞﺻو درز قﺮﺑ ﻊﺒﻨﻣ ﻢﯿﺳ ﻪﮐ ﯽﻣﺎﮕﻨﻫ
.ﺪﺷﺎﺑ شﻮﻣﺎﺧ قاﺮﺘﺣا ﺪﯿﻠﮐ ﻪﮐ ﯽﻣﺎﮕﻨﻫ ﯽﺘﺣ دﻮﺷ
ﻮﮔﺪﻨﻠﺑ لﺎﺼﺗا درﻮﻣ رد ﯽﺗﺎﮑﻧ
.ﺪﯿﻨﮐ شﻮﻣﺎﺧ ار هﺎﮕﺘﺳد ،ﺎﻫﻮﮔﺪﻨﻠﺑ ندﺮﮐ ﻞﺻو زا ﺶﯿﭘ
ﻪﻣﺪﺻ زا ﺎﺗ ﺪﯿﻨﮐ هدﺎﻔﺘﺳا قﺮﺑ یﻻﺎﺑ ﺖﯿﻓﺮﻇ ﺎﺑ و ،ﻢﻫا
8
ﺎﺗ
4
ﺲﻧاﺪﭙﻣا ﺎﺑ ﺎﻫﻮﮔﺪﻨﻠﺑ زا
.دﻮﺷ یﺮﯿﮔﻮﻠﺟ نآ ﻪﺑ
یﺎﻫﻮﮔﺪﻨﻠﺑ یﺎﻫ لﺎﻨﯿﻣﺮﺗ ﺎﯾ ،ﺪﯿﻨﮑﻧ ﻞﺻو ﻞﯿﺒﻣﻮﺗا ﯽﺳﺎﺷ ﻪﺑ ار ﻮﮔﺪﻨﻠﺑ یﺎﻫ لﺎﻨﯿﻣﺮﺗ
.ﺪﯿﻨﮑﻧ ﻞﺻو ﭗﭼ یﺎﻫﻮﮔﺪﻨﻠﺑ یﺎﻫ لﺎﻨﯿﻣﺮﺗ ﻪﺑ ار ﺖﺳار
.ﺪﯿﻨﮑﻧ ﻞﺻو ﻮﮔﺪﻨﻠﺑ (
–
) ﯽﻔﻨﻣ لﺎﻨﯿﻣﺮﺗ ﻪﺑ ار هﺎﮕﺘﺳد ﻦﯾا ﻦﯿﻣز ﻢﯿﺳ
.ﺪﯿﻨﮐ ﻞﺻو یزاﻮﻣ رﻮﻄﺑ ار ﺎﻫﻮﮔﺪﻨﻠﺑ ﺪﯿﻨﮑﻧ ﯽﻌﺳ
ﺖﯾﻮﻘﺗ ﺎﺑ) لﺎﻌﻓ یﺎﻫﻮﮔﺪﻨﻠﺑ ندﺮﮐ ﻞﺻو .ﺪﯿﻨﮐ ﻞﺻو ار لﺎﻌﻓ ﺮﯿﻏ یﺎﻫﻮﮔﺪﻨﻠﺑ ﺎﻬﻨﺗ
.ﺪﻨﮐ دراو ﻪﻣﺪﺻ هﺎﮕﺘﺳد ﻪﺑ ﺖﺳا ﻦﮑﻤﻣ ﻮﮔﺪﻨﻠﺑ یﺎﻫ لﺎﻨﯿﻣﺮﺗ ﻪﺑ (ﯽﻠﺧاد یﺎﻫ هﺪﻨﻨﮐ
رد هﺪﺷ ﺐﺼﻧ ﯽﻠﺧاد یﻮﮔﺪﻨﻠﺑ یﺎﻫ ﻢﯿﺳ زا ،دﺮﮑﻠﻤﻋ ءﻮﺳ ﮏﯾ زا بﺎﻨﺘﺟا یاﺮﺑ
یاﺮﺑ کﺮﺘﺸﻣ (
–
) ﯽﻔﻨﻣ ﻢﯿﺳ ﮏﯾ یاراد هﺎﮕﺘﺳد ﻪﮐ ﯽﺗرﻮﺻ رد دﻮﺧ ﻞﯿﺒﻣﻮﺗا
.ﺪﯿﻨﮑﻧ هدﺎﻔﺘﺳا ﺪﺷﺎﺑ ﯽﻣ ﭗﭼ و ﺖﺳار یﺎﻫﻮﮔﺪﻨﻠﺑ
.ﺪﯿﻨﮑﻧ ﻞﺻو ﺮﮕﯾﺪﮑﯾ ﻪﺑ ار هﺎﮕﺘﺳد یﻮﮔﺪﻨﻠﺑ یﺎﻫ ﻢﯿﺳ
لﺎﺼﺗا درﻮﻣ رد یا ﻪﺘﮑﻧ
ﺶﯾﺎﻤﻧ ﻪﺤﻔﺻ رد
"FAILURE"
،ﺪﻨﺷﺎﺑ هﺪﺸﻧ ﻞﺻو ﺢﯿﺤﺻ رﻮﻄﺑ ﺮﯾﺎﻓ ﯽﻠﭙﻣآ و ﻮﮔﺪﻨﻠﺑ ﺮﮔا
ﺢﯿﺤﺻ رﻮﻄﺑ ﺮﯾﺎﻓ ﯽﻠﭙﻣآ و ﻮﮔﺪﻨﻠﺑ ﻪﮐ ﺪﯾﻮﺷ ﻦﺌﻤﻄﻣ ،ﯽﺘﻟﺎﺣ ﻦﯿﻨﭼ رد .دﻮﺷ ﯽﻣ ﺮﻫﺎﻇ
.ﺪﻧا هﺪﺷ ﺐﺼﻧ
ﯽﺳرﺎﻓ
تﺎﻃﺎﯿﺘﺣا
ﻦﯿﻣز ﯽﻔﻨﻣ ﺖﻟو
12
ﻢﯿﻘﺘﺴﻣ قﺮﺑ تﺎﯿﻠﻤﻋ یاﺮﺑ ﺎﻬﻨﺗ هﺎﮕﺘﺳد ﻦﯾا
.ﺖﺳا هﺪﺷ ﯽﺣاﺮﻃ
لﺎﺜﻣ یاﺮﺑ) کﺮﺤﺘﻣ تﺎﻌﻄﻗ نﺎﯿﻣ ﺎﯾ ،ﺪﯿﻫﺪﻧ راﺮﻗ ﭻﯿﭘ ﮏﯾ ﺮﯾز ار ﻢﯿﺳ
.ﺪﯿﻫﺪﻧ ﺮﯿﮔ (ﯽﻟﺪﻨﺻ ﻞﯾر
زا ﺎﺗ ﺪﯿﻨﮐ شﻮﻣﺎﺧ ار ﻞﯿﺒﻣﻮﺗا ترﺎﺘﺳا ﭻﯿﯾﻮﺳ ،تﻻﺎﺼﺗا دﺎﺠﯾا زا ﻞﺒﻗ
.ﺪﯿﻨﮐ یﺮﯿﮔﻮﻠﺟ هﺎﺗﻮﮐ تﻻﺎﺼﺗا
ﻞﺻو ﺎﻫ ﻢﯿﺳ ﺮﯾﺎﺳ ﻪﮐ ﯽﻣﺎﮕﻨﻫ ﺎﻬﻨﺗ ار ﺰﻣﺮﻗ و درز قﺮﺑ ﻊﺒﻨﻣ یﺎﻫ ﻢﯿﺳ
.ﺪﯿﻨﮐ ﻞﺻو ﺪﻧا هﺪﺷ
.ﺪﯿﺸﮑﺑ ﻦﯿﻣز کﺮﺘﺸﻣ ﻪﻄﻘﻧ ﮏﯾ ﻪﺑ ار ﻦﯿﻣز یﺎﻫ ﻢﯿﺳ مﺎﻤﺗ
ﯽﻗﺮﺑ ﺐﺴﭼ راﻮﻧ ﺎﺑ ار ﻞﺷ هﺪﺸﻧ ﻞﺻو ﻢﯿﺳ ﺮﻫ ﯽﻨﻤﯾا رﻮﻈﻨﻣ ﻪﺑ ﺎﻤﺘﺣ
.ﺪﯿﻨﮐ یﺪﻨﺑ ﻖﯾﺎﻋ
(درز) قﺮﺑ ﻊﺒﻨﻣ ﻢﯿﺳ درﻮﻣ رد تﺎﮑﻧ
،ﺮﮕﯾد ﻮﯾﺮﺘﺳا یﺎﻫ هﺎﮕﺘﺳد ﺎﺑ ﺐﯿﮐﺮﺗ رد هﺎﮕﺘﺳد ﻦﯾا ندﺮﮐ ﻞﺻو مﺎﮕﻨﻫ
ﺮﺗﻻﺎﺑ هﺎﮕﺘﺳد ﺮﻫ زﻮﯿﻓ عﻮﻤﺠﻣ زا ﺪﯾﺎﺑ هﺪﺷ ﻞﺻو ﻞﯿﺒﻣﻮﺗا راﺪﻣ ﺢﻄﺳ
.ﺪﺷﺎﺑ
ار هﺎﮕﺘﺳد ،ﺖﺴﯿﻧ ﻻﺎﺑ ﯽﻓﺎﮐ هزاﺪﻧا ﻪﺑ ﻞﯿﺒﻣﻮﺗا راﺪﻣ ﭻﯿﻫ ﻪﮐ ﯽﻣﺎﮕﻨﻫ
.ﺪﯿﻨﮐ ﻞﺻو یﺮﺗﺎﺑ ﻪﺑ ﺎﻤﯿﻘﺘﺴﻣ
(
)
لﺎﺼﺗا ﻪﻧﻮﻤﻧ
(
-C)
ﺮﻓوو بﺎﺳ ﻢﯿﻘﺘﺴﻣ لﺎﺼﺗا
ﯽﺗﺎﯿﻠﻤﻋ یﺎﻫ ﻞﻤﻌﻟارﻮﺘﺳد ﻪﺑ ،لﺎﺼﺗا ﻪﺑ طﻮﺑﺮﻣ تﺎﯿﺋﺰﺟ صﻮﺼﺧرد
.ﺪﯿﻨﮐ ﻪﻌﺟاﺮﻣ ﻪﻤﯿﻤﺿ
.ﺪﯿﻨﮑﻧ ﻞﺻو ﻮﮔﺪﻨﻠﺑ لﺎﺼﺗا ﻦﯾا رد
*
تﺎﮑﻧ
.ﺪﯿﻨﮐ ﻞﺻو ﺮﯾﺎﻓ ﯽﻠﭙﻣآ لﺎﺼﺗا زا ﺶﯿﭘ ار ﻦﯿﻣز ﻢﯿﺳ ﺎﻤﺘﺣ
.ﺪﻨﮐ ﯽﻣ اﺪﺻ ﮓﻧز ﯽﻠﺧاد ﺮﯾﺎﻓ ﯽﻠﭙﻣآ زا هدﺎﻔﺘﺳا مﺎﮕﻨﻫ ﺎﻬﻨﺗ
A
B
C
*
*
2
*
2
*
1
REM OUT
Max. supply current 0.4 A
ﺮﻴﺒﻣأ
0.4
رﺎﻴﺘﻠﻟ داﺪﻣإ ﻰﺼﻗأ
ﺮﭙﻣآ
0.4
ﯽﻠﻌﻓ هﺮﯿﺧذ ﺮﺜﮐاﺪﺣ
Fuse (10 A)
(ﺮﻴﺒﻣأ
10
) ﺮﻬﺼﻨﻣ
(ﺮﭙﻣآ
10
) زﻮﯿﻓ
Blue/white striped
ﺾﻴﺑأ/قرزأ ﻂﻄﺨﻣ
ﺪﯿﻔﺳ/ﯽﺑآ هار هار ﻢﯿﺳ
ACC
BATTERY
ILLUMINATION
from car antenna (aerial)
ةرﺎﻴﺴﻟا ﻲﺋاﻮﻫ ﻦﻣ
وردﻮﺧ ﻦﺘﻧآ زا
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
RCA pin cord (not supplied).
*
3
AUDIO OUT can be switched SUB or REAR. For details, see the
supplied Operating Instructions.
supplied Operating Instructions.
*
4
Separate adaptor may be required.
4 × ﻢﻫا 8 ﺎﺗ 4 :ﻮﮔﺪﻨﻠﺑ ﺲﻧاﺪﭙﻣا
1
*
.(ﺖﺳا هﺪﺸﻧ ﻪﺋارا)
RCA
ﻦﯿﭘ ﻢﯿﺳ
2
*
ﺐﺴﮐ یاﺮﺑ .ﺪﻨﮐ اﺪﯿﭘ ﺮﯿﯿﻐﺗ
REAR
ﺎﯾ
SUB
ﻪﺑ ﺪﻧاﻮﺗ ﯽﻣ
AUDIO OUT
3
*
.ﺪﯿﻨﮐ هﺪﻫﺎﺸﻣ ار هﺪﺷ ﻪﺋارا ﯽﺗﺎﯿﻠﻤﻋ یﺎﻫ ﻞﻤﻌﻟارﻮﺘﺳد ،تﺎﯿﺋﺰﺟ
.ﺪﺷﺎﺑ مزﻻ ﻪﻧﺎﮔاﺪﺟ رﻮﺘﭘادآ ﺖﺳا ﻦﮑﻤﻣ
4
*
4 × موأ 8 – 4 :ﺔﻋﺎﻤﺴﻟا ﺔﻗوﺎﻌﻣ
1
*
.(ﻖﻓﺮﻣ ﺮﻴﻏ)
RCA
ﻲﺳﻮﺑد ﻚﻠﺳ
2
*
،ﻞﻴﺻﺎﻔﺘﻠﻟ .
REAR
وأ
SUB
ﻦﻴﺑ
AUDIO OUT
تﻮﺼﻟا جﺮﺧ ﺮﻴﻴﻐﺗ ﻦﻜﻤﻳ
3
*
.ﺔﻘﻓﺮﻤﻟا ﻞﻴﻐﺸﺘﻟا تﺎﻤﻴﻠﻌﺗ ﻊﺟار
.ﻞﺼﻔﻨﻣ ﺊﻳﺎﻬﻣ ﺮﻓﻮﺗ مﺰﻠﻳ ﺪﻗ
4
*
Front speaker
ﺔﻴﻣﺎﻣﻷا ﺔﻋﺎﻤﺴﻟا
ﯽﯾﻮﻠﺟ یﻮﮔﺪﻨﻠﺑ
Subwoofer
تﻮﺼﻟا ﻢﺨﻀﻣ
ﺮﻓوﻮﺑﺎﺳ
Equipment used in illustrations (not supplied)
(ﺔﻘﻓﺮﻣ ﺮﻴﻏ) ﺔﻴﺤﻴﺿﻮﺘﻟا لﺎﻜﺷﻷا ﻲﻓ ﺔﻣﺪﺨﺘﺴﻣ ةﺰﻬﺟأ
(ﺖﺴﯿﻧ ﻪﻤﯿﻤﺿ) ﺮﯾوﺎﺼﺗ رد هدﺎﻔﺘﺳا درﻮﻣ تاﺰﯿﻬﺠﺗ
Power amplifier
ﻂﺸﻧ ﻢﺨﻀﻣ
ﯽﻗﺮﺑ ﺮﯾﺎﻓ ﯽﻠﭙﻣآ
Rear speaker
ﺔﻴﻔﻠﺨﻟا ﺔﻋﺎﻤﺴﻟا
ﯽﺒﻘﻋ یﻮﮔﺪﻨﻠﺑ
Orange/white striped
Yellow
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Left
Right
Black
Purple/black striped
Left
Right
دﻮﺳأ
ﺾﻴﺑأ/ﻲﻟﺎﻘﺗﺮﺑ ﻂﻄﺨﻣ
ﺮﻔﺻأ
ﺾﻴﺑأ
دﻮﺳأ/ﺾﻴﺑأ ﻂﻄﺨﻣ
يدﺎﻣر
دﻮﺳأ/يدﺎﻣر ﻂﻄﺨﻣ
ﺮﻀﺧأ
دﻮﺳأ/ﺮﻀﺧأ ﻂﻄﺨﻣ
ﻲﺠﺴﻔﻨﺑ
دﻮﺳأ/ﻲﺠﺴﻔﻨﺑ ﻂﻄﺨﻣ
ىﺮﺴﻳ
ﻰﻨﻤﻳ
ىﺮﺴﻳ
ﻰﻨﻤﻳ
هﺎﯿﺳ
ﺪﯿﻔﺳ/ﯽﺠﻧرﺎﻧ هار هار
درز
ﺪﯿﻔﺳ
هﺎﯿﺳ/ﺪﯿﻔﺳ هار هار ﻢﯿﺳ
یﺮﺘﺴﮐﺎﺧ
هﺎﯿﺳ/یﺮﺘﺴﮐﺎﺧ هار هار ﻢﯿﺳ
ﺰﺒﺳ
هﺎﯿﺳ/ﺰﺒﺳ هار هار ﻢﯿﺳ
ﯽﻧاﻮﻏرا
هﺎﯿﺳ/ﯽﻧاﻮﻏرا هار هار ﻢﯿﺳ
ﭗﭼ
ﺖﺳار
ﭗﭼ
ﺖﺳار
Red
ﺮﻤﺣأ
ﺰﻣﺮﻗ
(
)
ﺔﻴﻧﺎﺑﺎﻳ ةرﺎﻴﺳ ﻲﻓ زﺎﻬﺠﻟا ﺐﻴﻛﺮﺗ
هﺬﻫ ﻲﻓ .ﺔﻴﻧﺎﺑﺎﻴﻟا تارﺎﻴﺴﻟا ﺾﻌﺑ ﻲﻓ زﺎﻬﺠﻟا اﺬﻫ ﺐﻴﻛﺮﺗ ﻦﻣ ﻦﻜﻤﺘﺗ ﻻ ﺪﻗ
.
Sony
ﻲﻧﻮﺳ ﻞﻴﻛو ﺮﺸﺘﺳا ،ﺔﻟﺎﺤﻟا
ﺔﻈﺣﻼﻣ
.ﻂﻘﻓ ﺔﻘﻓﺮﻤﻟا ﻲﻏاﺮﺒﻟا ﺎًﻣﺪﺨﺘﺴﻣ ﺐﻴﻛﺮﺘﻟﺎﺑ ﻢﻗ ،ﻞﻠﺧ ثوﺪﺣ يدﺎﻔﺘﻟ
(
)
ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺐﻴﻛﺮﺗو ﻞﺼﻓ ﺔﻴﻔﻴﻛ
.ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﻞﺼﻓ ﻦﻣ ﺪﻛﺄﺗ ،زﺎﻬﺠﻟا ﺐﻴﻛﺮﺗ ﻞﺒﻗ
ﻞﺼﻔﻠﻟ
-A
ﻰﻠﻋ راﺮﻤﺘﺳﻻا ﻊﻣ ﻂﻐﻀﻟا ﻦﻣ ﺪﻛﺄﺗ ،ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﻞﺼﻓ ﻞﺒﻗ
ﺎﻬﺒﺤﺳاو ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺮﻳﺮﺤﺗ رز ﻰﻠﻋ ﻂﻐﺿا .
.ﻚﻫﺎﺠﺗ جرﺎﺨﻠﻟ
ﺐﻴﻛﺮﺘﻠﻟ
-B
ءﺰﺠﻟا ﻊﻣ ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﻰﻠﻋ دﻮﺟﻮﻤﻟا ءﺰﺠﻟا ﻖﻴﺸﻌﺘﺑ ﻢﻗ
ﻊﻓدا ﻢﺛ ،ﻲﺤﻴﺿﻮﺘﻟا ﻞﻜﺸﻟا ﻲﻓ ﻦﻴﺒﻣ ﻮﻫ ﺎﻤﻛ ،ةﺪﺣﻮﻟا ﻰﻠﻋ دﻮﺟﻮﻤﻟا
.ﺔﻘﻃ ﻊﻤﺴﺗ نأ ﻰﻟإ ﻪﻧﺎﻜﻣ ﻲﻓ ﺮﺴﻳﻷا ﺐﻧﺎﺠﻟا
صﺎﺨﻟا كﺮﺤﻤﻟا لﺎﻌﺷإ مﺎﻈﻧ نﺎﻛ اذإ ﺮﻳﺬﺤﺗ
ACC
تﺎﻴﻟﺎﻤﻜﻟا ﻊﺿﻮﻤﺑ ﺰﻬﺠﻣ ﺮﻴﻏ ﻚﺗرﺎﻴﺴﺑ
تﺎﻤﻴﻠﻌﺗ ﻊﺟار ،ﻞﻴﺻﺎﻔﺘﻠﻟ .ﻲﺋﺎﻘﻠﺘﻟا فﺎﻘﻳﻹا ﺔﻔﻴﻇو ﺔﺌﻴﻬﺗ ﻦﻣ ﺪﻛﺄﺗ
.ﺔﻘﻓﺮﻤﻟا ﻞﻴﻐﺸﺘﻟا
ءﺎﻔﻄﻧا ﺪﻌﺑ دﺪﺤﻤﻟا ﺖﻗﻮﻟا ﻲﻓ ﺎًﻴﺋﺎﻘﻠﺗ ﻞﻣﺎﻛ ﻞﻜﺸﺑ زﺎﻬﺠﻟا ﺊﻔﻄﻨﻴﺳ
.ﺔﻳرﺎﻄﺒﻟا ﺔﻨﺤﺷ كﻼﻬﺘﺳا يدﺎﻔﺘﻟ ﻚﻟذو ،زﺎﻬﺠﻟا
رﺰﻟا ﻂﻐﻀﺑ ﻆﻔﺘﺣﺎﻓ ،ﻲﺋﺎﻘﻠﺘﻟا فﺎﻘﻳﻹا ﺔﻔﻴﻇو ﺔﺌﻴﻬﺘﺑ ﻢﻘﺗ ﻢﻟ اذإ
مﺎﻈﻧ ءﺎﻔﻃﺈﺑ ﺖﻤﻗ ﺎﻤﻠﻛ ﺔﺷﺎﺸﻟا ﻲﻔﺘﺨﺗ نأ ﻰﻟإ
.كﺮﺤﻤﻟا لﺎﻌﺷإ
(
)
ﺮﻬﺼﻨﻤﻟا لاﺪﺒﺘﺳا
لﺪﻌﻣ ﻊﻣ ﻢﺋﻼﺘﻳ ﺮﻬﺼﻨﻣ لﺎﻤﻌﺘﺳا ﻦﻣ ﺪﻛﺄﺗ ،ﺮﻬﺼﻨﻤﻟا لاﺪﺒﺘﺳا ﺪﻨﻋ
ﻦﻣ ﺪﻛﺄﺘﻓ ،ﺮﻬﺼﻨﻤﻟا قﺮﺘﺣا اذإ .ﻲﻠﺻﻷا ﺮﻬﺼﻨﻤﻟا ﻰﻠﻋ بﻮﺘﻜﻤﻟا ﺔﻳﺮﻴﺒﻣﻷا
ﺪﻌﺑ ىﺮﺧأ ةﺮﻣ ﺮﻬﺼﻨﻤﻟا قﺮﺘﺣا اذإ .ﺮﻬﺼﻨﻤﻟا لﺪﺒﺘﺳاو ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ
ﻞﻴﻛو بﺮﻗأ ﺮﺸﺘﺳا ،ﺔﻟﺎﺤﻟا هﺬﻫ ﻲﻓ .ﻲﻠﺧاد ﻞﻠﺧ ﺪﺟﻮﻳ ﺪﻘﻓ ،لاﺪﺒﺘﺳﻻا
.
Sony
ﻲﻧﻮﺳ
ﯽﺳرﺎﻓ
ﺎﻫرﺎﻄﺧا
لﻮﻤﻌﻣ تﺎﯿﻠﻤﻋ ﺎﺑ هﺎﮕﺘﺳد ﺎﺗ ﺪﯿﻨﮐ بﺎﺨﺘﻧا ﺖﻗد ﻪﺑ ار ﺐﺼﻧ ﻞﺤﻣ
.ﺪﻨﮑﻧ اﺪﯿﭘ ﻞﺧاﺪﺗ ﯽﮔﺪﻨﻧار
شزﺮﻟ ،ﯽﻔﯿﺜﮐ ،کﺎﺧ و دﺮﮔ ضﺮﻌﻣ رد ﻪﮐ ﯽﻘﻃﺎﻨﻣ رد هﺎﮕﺘﺳد ﺐﺼﻧ زا
ﮏﯾدﺰﻧ ﺎﯾ ﺪﯿﺷرﻮﺧ ﻢﯿﻘﺘﺴﻣ رﻮﻧ ﺪﻨﻧﺎﻣ ،ﻻﺎﺑ یﺎﻫﺎﻣد ﺎﯾ ،ﺪﺣ زا ﺶﯿﺑ
.ﺪﯿﻨﮐ یراددﻮﺧ ﯽﯾﺎﻣﺮﮔ یﺎﻫ لﺎﻧﺎﮐ
هﺪﺷ ﻪﻤﯿﻤﺿ ﺐﺼﻧ هﺎﮕﺘﺳد زا ﺎﻬﻨﺗ ﻦﺌﻤﻄﻣ و ﻦﻤﯾا ﺐﺼﻧ ﮏﯾ یاﺮﺑ
.ﺪﯿﻨﮐ هدﺎﻔﺘﺳا
ﺐﺼﻧ ﻪﯾواز ﻢﯿﻈﻨﺗ
.ﺪﯿﻨﮐ ﻢﯿﻈﻨﺗ ﻪﺟرد زا ﺮﺘﻤﮐ ﻪﺑ ار ﺐﺼﻧ ﻪﯾواز
(
)
بﻼﻗ و ﻆﻓﺎﺤﻣ ﻪﻧﺪﺑ ندﺮﮐ جرﺎﺧ
اﺪﺟ هﺎﮕﺘﺳد زا ار بﻼﻗ و ﻆﻓﺎﺤﻣ ﻪﻧﺪﺑ ،هﺎﮕﺘﺳد ﺐﺼﻧ زا ﺶﯿﭘ
.ﺪﯿﻨﮐ
.ﺪﯿﻨﮐ جرﺎﺧ ار
ﻆﻓﺎﺤﻣ ﻪﻧﺪﺑ 1
نوﺮﯿﺑ ار نآ ﺲﭙﺳ ،ﺪﯿﻫد رﺎﺸﻓ ار ﻆﻓﺎﺤﻣ ﻪﻧﺪﺑ ﻪﺷﻮﮔ ود ﺮﻫ
.ﺪﯿﺸﮑﺑ
.ﺪﯿﻨﮐ جرﺎﺧ ار بﻼﻗ 2
و هﺎﮕﺘﺳد نﺎﯿﻣ ﻪﺑ ﺮﮕﯾﺪﮑﯾ ﺎﺑ ار یزﺎﺳدازآ ﺪﯿﻠﮐ ود ﺮﻫ
.ﺪﻨﻫﺪﺑ ﮏﯿﺗ یاﺪﺻ ﺎﺗ ﺪﯿﻨﮐ دراو بﻼﻗ
ﺪﯿﺸﮑﺑ ﻻﺎﺑ ﻪﺑ ار هﺎﮕﺘﺳد ﺲﭙﺳ ،ﺪﯿﺸﮑﺑ ﻦﯿﯾﺎﭘ ﻪﺑ ار
بﻼﻗ
.دﻮﺷ اﺪﺟ ﺎﺗ
(
)
ﺐﺼﻧ ﻪﻧﻮﻤﻧ
درﻮﺒﺷاد رد ﺐﺼﻧ
تﺎﮑﻧ
ﻪﺑ ﺮﺘﻤﯿﻠﯿﻣ
2
بﻼﻗ فﺮﻃ ود ﺮﻫ رد ﺎﻫ هﺮﯿﮔ ﻪﮐ ﺪﯾﻮﺷ ﻦﺌﻤﻄﻣ ،ﺐﺼﻧ زا ﺶﯿﭘ
هﺪﺷ ﻢﺧ نوﺮﯿﺑ ﺖﻤﺳ ﻪﺑ ﺎﯾ ﺪﻨﺘﺴﻫ فﺎﺻ ﺎﻫ هﺮﯿﮔ ﺮﮔا .ﺪﻧا هﺪﺷ ﻢﺧ ﻞﺧاد ﺖﻤﺳ
دﻮﺷ بﺎﺗﺮﭘ نوﺮﯿﺑ ﻪﺑ ﺖﺳا ﻦﮑﻤﻣ و ﺪﺷ ﺪﻫاﻮﺨﻧ ﺐﺼﻧ ﻦﻤﯾا رﻮﻄﺑ هﺎﮕﺘﺳد ،ﺪﻧا
.
( -1)
.
(
-2)
ﺪﯿﻨﮐ ﻢﺧ نوﺮﯿﺑ ﻪﺑ ،زﺎﯿﻧ ترﻮﺻ رد ،ﻢﮑﺤﻣ یﺮﯿﮔﺎﺟ یاﺮﺑ ار ﺎﻫ هﺮﯿﮔ ﻦﯾا
فﺎﮑﺷ رد ﺢﯿﺤﺻ رﻮﻄﺑ ﻆﻓﺎﺤﻣ ﻪﻧﺪﺑ یور ﺮﺑ هﺮﯿﮔ
4
ﻪﮐ ﺪﯿﻨﮐ ﻞﺻﺎﺣ نﺎﻨﯿﻤﻃا
.
(
-3)
ﺪﻧا هدﺎﺘﻓا ﺎﺟ هﺎﮕﺘﺳد یﺎﻫ
Mounting the unit in a
Japanese car (
Japanese car (
)
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws
To prevent malfunction, install only with the supplied screws
.
How to detach and attach the
front panel (
front panel (
)
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press and hold
. Press the front panel release button, and
pull it off towards you.
-B To attach
Engage part
of the front panel with part
of the unit,
as illustrated, and push the left side into position until it
clicks.
clicks.
Warning if your car’s ignition
has no ACC position
has no ACC position
Be sure to set the Auto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents battery
drain.
If you do not set the Auto Off function, press and hold
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents battery
drain.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
Fuse replacement (
)
When replacing the fuse, be sure to use one matching the
amperage rating stated on the original fuse. If the fuse
blows, check the power connection and replace the fuse. If
the fuse blows again after replacement, there may be an
internal malfunction. In such a case, consult your nearest
Sony dealer.
amperage rating stated on the original fuse. If the fuse
blows, check the power connection and replace the fuse. If
the fuse blows again after replacement, there may be an
internal malfunction. In such a case, consult your nearest
Sony dealer.
ﯽﻨﭘاژ ﻞﯿﺒﻣﻮﺗا ﮏﯾ رد هﺎﮕﺘﺳد ندﺮﮐ ﺐﺼﻧ
(
)
یﺎﻫ ﻞﯿﺒﻣﻮﺗا زا ﯽﻀﻌﺑ رد ار هﺎﮕﺘﺳد ﺪﯿﺷﺎﺒﻧ ردﺎﻗ ﺖﺳا ﻦﮑﻤﻣ ﺎﻤﺷ
دﻮﺧ
ﯽﻧﻮﺳ هﺪﻨﺷوﺮﻓ ﺎﺑ ،ﯽﺘﻟﺎﺣ ﻦﯿﻨﭼ رد .ﺪﯿﻨﮐ ﺐﺼﻧ ﻦﭘاژ ﺖﺧﺎﺳ
.ﺪﯿﯾﺎﻤﻧ ترﻮﺸﻣ
ﻪﺘﮑﻧ
.ﺪﯿﻨﮐ ﺐﺼﻧ هﺪﺷ ﻪﻤﯿﻤﺿ یﺎﻫ ﭻﯿﭘ ﺎﺑ ﺎﻬﻨﺗ ،دﺮﮑﻠﻤﻋ ءﻮﺳ زا یﺮﯿﮔﻮﻠﺟ یاﺮﺑ
ﯽﯾﻮﻠﺟ ﻞﻧﺎﭘ ندﺮﮐ ﻞﺻو و ندﺮﮐ اﺪﺟ هﻮﺤﻧ
(
)
.ﺪﯿﻨﮐ اﺪﺟ ار ﯽﯾﻮﻠﺟ ﻞﻧﺎﭘ ،هﺎﮕﺘﺳد ندﺮﮐ ﺐﺼﻧ زا ﺶﯿﭘ
ندﺮﮐ اﺪﺟ یاﺮﺑ
-A
و ﺪﯿﻫد رﺎﺸﻓ ار
،ﯽﯾﻮﻠﺟ ﻪﺤﻔﺻ ندﺮﮐ اﺪﺟ زا ﻞﺒﻗ
ﺖﻤﺳ ﻪﺑ ار نآ و ﺪﯿﻫد رﺎﺸﻓ ار ﻮﻠﺟ ﻪﺤﻔﺻ یزﺎﺳﺎﻫر ﻪﻤﮐد .ﺪﯾراﺪﻬﮕﻧ
.ﺪﯾﺎﯿﺑ نوﺮﯿﺑ ﺎﺗ ﺪﯿﺸﮑﺑ دﻮﺧ
ندﺮﮐ ﻞﺻو یاﺮﺑ
-B
ﻞﮑﺷ ﻪﮐ رﻮﻄﻧﺎﻤﻫ ،هﺎﮕﺘﺳد ﺖﻤﺴﻗ ﺎﺑ ار ﯽﯾﻮﻠﺟ ﻞﻧﺎﭘ زا ﺖﻤﺴﻗ
ﺎﺗ ﺪﯿﺸﮑﺑ ﺖﯿﻌﻗﻮﻣ ﻞﺧاد ﻪﺑ ار ﭗﭼ ﺖﻤﺳ و ﺪﯿﻨﮐ ﺮﯿﮔرد ،ﺪﻫد ﯽﻣ نﺎﺸﻧ
.ﺪﻫﺪﺑ ﮏﯿﺗ یاﺪﺻ
ﻞﯿﺒﻣﻮﺗا ترﺎﺘﺳا ﭻﯿﯾﻮﺳ ﻪﮐ ﯽﺗرﻮﺻ رد راﺪﺸﻫ
ﺪﺷﺎﺑ ﯽﻤﻧ
ACC
ﺖﯿﻌﻗﻮﻣ یاراد ﺎﻤﺷ
ﻢﯿﻈﻨﺗ ار
رﺎﮐدﻮﺧ ﯽﺷﻮﻣﺎﺧ دﺮﮑﻠﻤﻋ ﻪﮐ ﺪﯿﻨﮐ ﻞﺻﺎﺣ نﺎﻨﯿﻤﻃا
ار هﺪﺷ ﻪﻤﯿﻤﺿ ﯽﺗﺎﯿﻠﻤﻋ یﺎﻫ ﻞﻤﻌﻟارﻮﺘﺳد ،تﺎﯿﺋﺰﺟ یاﺮﺑ .ﺪﯿﻨﮐ ﯽﻣ
.ﺪﯿﯾﺎﻤﻧ ﻪﻈﺣﻼﻣ
رﺎﮐدﻮﺧ و ﻞﻣﺎﮐ رﻮﻄﺑ هﺪﺷ ﻦﯿﯿﻌﺗ نﺎﻣز رد ﯽﺷﻮﻣﺎﺧ زا ﺪﻌﺑ هﺎﮕﺘﺳد
.ﺪﻨﮐ ﯽﻣ یﺮﯿﮔﻮﻠﺟ یﺮﺗﺎﺑ نﺪﺷ ﯽﻟﺎﺧ زا ﻪﮐ ،دﻮﺷ ﯽﻣ شﻮﻣﺎﺧ
ﺮﻫ ،ﺪﯾا هدﺮﮑﻧ ﻢﯿﻈﻨﺗ ار
رﺎﮐدﻮﺧ ﯽﺷﻮﻣﺎﺧ دﺮﮑﻠﻤﻋ ﺎﻤﺷ ﺮﮔا
رﺎﺸﻓ ار
ﺪﯿﻨﮐ ﯽﻣ شﻮﻣﺎﺧ ار قاﺮﺘﺣا ﺎﻤﺷ ﻪﮐ رﺎﺑ
.دﻮﺷ ﻮﺤﻣ ﺶﯾﺎﻤﻧ ﻪﺤﻔﺻ ﺎﺗ ﺪﯾراد هﺎﮕﻧ و هداد
(
)
زﻮﯿﻓ ﯽﻨﯾﺰﮕﯾﺎﺟ
ﺎﺑ ﻖﺑﺎﻄﻣ زﻮﯿﻓ ﮏﯾ زا ﻪﮐ ﺪﯾﻮﺷ ﻦﺌﻤﻄﻣ ،زﻮﯿﻓ ندﺮﮐ ﻦﯾﺰﮕﯾﺎﺟ مﺎﮕﻨﻫ
،ﺖﺧﻮﺳ زﻮﯿﻓ ﺮﮔا .ﺪﯿﻨﮐ ﯽﻣ هدﺎﻔﺘﺳا ﯽﻠﺻا زﻮﯿﻓ رد هﺪﺷ ﺮﮐذ ﺮﭙﻣآ ناﺰﯿﻣ
زا ﺪﻌﺑ زﻮﯿﻓ ﺮﮔا .ﺪﯿﻨﮐ ﻦﯾﺰﮕﯾﺎﺟ ار زﻮﯿﻓ و ﺪﯿﻨﮐ ﯽﻨﯿﺑزﺎﺑ ار قﺮﺑ لﺎﺼﺗا
دﻮﺟو ﯽﻠﺧاد دﺮﮑﻠﻤﻋ ءﻮﺳ ﮏﯾ ﺖﺳا ﻦﮑﻤﻣ ،ﺖﺧﻮﺳ هرﺎﺑود ﯽﻨﯾﺰﮕﯾﺎﺟ
دﻮﺧ
Sony
ﯽﻧﻮﺳ هﺪﻨﺷوﺮﻓ ﻦﯾﺮﺘﮑﯾدﺰﻧ ﺎﺑ ،ﯽﺘﻟﺎﺣ ﻦﯿﻨﭼ رد .ﺪﺷﺎﺑ ﻪﺘﺷاد
.ﺪﯿﯾﺎﻤﻧ ترﻮﺸﻣ
ﺔﻴﺑﺮﻌﻟا ﺔﻐﻠﻟا
ﺔﻴﻃﺎﻴﺘﺣا تﺎﻬﻴﺒﻨﺗ
تﺎﻴﻠﻤﻋ ﻊﻣ ةﺪﺣﻮﻟا ﻞﺧاﺪﺘﺗ ﻻ ﺚﻴﺤﺑ ﺔﻳﺎﻨﻌﺑ ﺐﻴﻛﺮﺘﻟا ﻊﺿﻮﻣ ﺮﺘﺧا
.ﺔﻳدﺎﻌﻟا ةدﺎﻴﻘﻟا
زاﺰﺘﻫﻻا وأ خﺎﺳوﻷا وأ رﺎﺒﻐﻠﻟ ﺔﺿﺮﻌﻣ ﻦﻛﺎﻣأ ﻲﻓ زﺎﻬﺠﻟا ﺐﻴﻛﺮﺗ ﺐﻨﺠﺗ
ﺲﻤﺸﻟا ﺔﻌﺷأ ﺖﺤﺗ نﻮﻜﺗ نﺄﻛ ،ﺔﻴﻟﺎﻌﻟا ةراﺮﺤﻟا تﺎﺟرد وأ طﺮﻔﻤﻟا
.ﺔﺌﻓﺪﺘﻟا زﺎﻬﺟ ﻦﻣ بﺮﻘﻟﺎﺑ وأ ةﺮﺷﺎﺒﻤﻟا
ﺐﻴﻛﺮﺘﻟاو ﺔﻣﻼﺴﻟا ﻖﻴﻘﺤﺘﻟ ﻚﻟذو ﻂﻘﻓ ﺔﻘﻓﺮﻤﻟا ﺐﻴﻛﺮﺘﻟا ةادأ ﻞﻤﻌﺘﺳا
.ﻦﻣﻵا
ﺐﻴﻛﺮﺘﻟا ﺔﻳواز ﻂﺒﺿ
.ﺔﺟرد ﻦﻣ ﻞﻗأ ﺔﻳواﺰﺑ زﺎﻬﺠﻟا ﺐﻴﻛﺮﺘﺑ ﻢﻗ
(
)
ﺐﻴﻛ ﺮﺘﻟا ةﺪﻋﺎﻗو ﺔﻳﺎﻤﺤﻟا قﻮﻃ جاﺮﺧإ
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗو ﺔﻳﺎﻤﺤﻟا قﻮﻃ جاﺮﺧﺈﺑ ﻢﻗ ،زﺎﻬﺠﻟا ﺐﻴﻛﺮﺗ ﻞﺒﻗ
.زﺎﻬﺠﻟا ﻦﻣ
.
ﺔﻳﺎﻤﺤﻟا قﻮﻃ جاﺮﺧﺈﺑ ﻢﻗ 1
.جرﺎﺨﻠﻟ ﻪﺒﺤﺳا ﻢﺛ ، ﺔﻳﺎﻤﺤﻟا قﻮﻃ ﻲﺘﻓﺎﺣ ﻚﺴﻣأ
.
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ ﻞﺼﻓا 2
ةﺪﻋﺎﻗو زﺎﻬﺠﻟا ﻦﻴﺑ ﺪﺣاو نآ ﻲﻓ
ﺮﻳﺮﺤﺘﻟا ﻲﺣﺎﺘﻔﻣ ﻞﺧدأ
.ﺔﻘﻃ ﻊﻤﺴﺗ نأ ﻰﻟإ
ﺐﻴﻛﺮﺘﻟا
ﻰﻠﻋﻸﻟ زﺎﻬﺠﻟا ﺐﺤﺳا ﻢﺛ ،ﻞﻔﺳﻸﻟ
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ ﺐﺤﺳا
.ﺎﻬﻠﺼﻔﻟ
(
)
ﺐﻴﻛﺮﺘﻟا لﺎﺜﻣ
تاداﺪﻌﻟا ﺔﺣﻮﻟ ﻲﻓ ﺐﻴﻛﺮﺘﻟا
تﺎﻈﺣﻼﻣ
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ ﻲﺒﻧﺎﺟ ﻰﻠﻋ ةدﻮﺟﻮﻤﻟا تﺎﺟﻻﺰﻤﻟا ﻲﻨﺛ ﻦﻣ ﺪﻛﺄﺗ ،ﺐﻴﻛﺮﺘﻟا ﻞﺒﻗ
ﻢﺘﻳ ﻦﻠﻓ ،جرﺎﺨﻠﻟ ﺔﻴﻨﺜﻣ وأ ﺔﻤﻴﻘﺘﺴﻣ تﺎﺟﻻﺰﻤﻟا ﺖﻧﺎﻛ اذإ .ﻢﻣ
2
راﺪﻘﻤﺑ ﻞﺧاﺪﻠﻟ
.
( -1)
جرﺎﺨﻠﻟ زﺮﺒﻳ ﺪﻗو مﺎﻜﺣﺈﺑ زﺎﻬﺠﻟا ﺐﻴﻛﺮﺗ
ﺎًﻳروﺮﺿ ﻚﻟذ نﺎﻛ اذإ ،ﺔﻤﻜﺤﻣ ﺔﻤﺋﻼﻣ ﻖﻴﻘﺤﺘﻟ جرﺎﺨﻠﻟ ﺔﻬﺠﺘﻤﻟا ﺐﻟﺎﺨﻤﻟا هﺬﻫ ِﻦﺛا
.
(
-2)
ةدﻮﺟﻮﻤﻟا تﺎﺤﺘﻔﻟا ﻲﻓ ﺔﻳﺎﻤﺤﻟا قﻮﻃ ﻰﻠﻋ ةدﻮﺟﻮﻤﻟا ﻚﺑﺎﺸﻣ
4
ﻖﻴﺸﻌﺗ ﻦﻣ ﺪﻛﺄﺗ
.
(
-3)
ﺐﺳﺎﻨﻣ ﻞﻜﺸﺑ ةﺪﺣﻮﻟا ﻰﻠﻋ
English
Precautions
Choose the installation location carefully so that the unit
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection
collar and the bracket (
collar and the bracket (
)
Before installing the unit, remove the protection
collar
collar
and the bracket
from the unit.
1
Remove the protection collar
.
Pinch both edges of the protection collar
, then
pull it out.
2
Remove the bracket
.
Insert both release keys
together between
the unit and the bracket
until they click.
Pull down the bracket
, then pull up the unit
to separate.
Mounting example (
)
Installation in the dashboard
Notes
Before installing, make sure that the catches on both sides of the
bracket
bracket
are bent inwards 2 mm (
3
/
32
in). If the catches are straight or
bent outwards, the unit will not be installed securely and may spring
out
out
( -1).
Bend these claws outward for a tight fit, if necessary
( -2).
Make sure that the 4 catches on the protection collar
are properly
engaged in the slots of the unit
( -3).
Bracket
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ
بﻼﻗ
Bracket
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ
بﻼﻗ
Bracket
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ
بﻼﻗ
Bracket
ﺐﻴﻛﺮﺘﻟا ةﺪﻋﺎﻗ
بﻼﻗ
A
TOYOTA
B
NISSAN
to dashboard/center console
ﻂﺳوﻷا يوﺎﺤﻟا قوﺪﻨﺼﻟا/تاداﺪﻌﻟا ﺔﺣﻮﻟ ﻰﻟإ
یﺰﮐﺮﻣ ﻪﻧﺎﯾﺎﭘ/درﻮﺒﺷاد ﻪﺑ
to dashboard/center console
ﻂﺳوﻷا يوﺎﺤﻟا قوﺪﻨﺼﻟا/تاداﺪﻌﻟا ﺔﺣﻮﻟ ﻰﻟإ
یﺰﮐﺮﻣ ﻪﻧﺎﯾﺎﭘ/درﻮﺒﺷاد ﻪﺑ
Existing parts supplied with your car
ﻚﺗرﺎﻴﺳ ﻊﻣ ﺔﻘﻓﺮﻣ ةدﻮﺟﻮﻤﻟا ءاﺰﺟﻷا
دﻮﺧ ﻞﯿﺒﻣﻮﺗا ﺎﺑ هﺪﺷ ﻪﻤﯿﻤﺿ دﻮﺟﻮﻣ یﺎﻫ ﺖﻤﺴﻗ
Existing parts supplied with your car
ﻚﺗرﺎﻴﺳ ﻊﻣ ﺔﻘﻓﺮﻣ ةدﻮﺟﻮﻤﻟا ءاﺰﺟﻷا
دﻮﺧ ﻞﯿﺒﻣﻮﺗا ﺎﺑ هﺪﺷ ﻪﻤﯿﻤﺿ دﻮﺟﻮﻣ یﺎﻫ ﺖﻤﺴﻗ
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
ﻢﺠﺤﻟا
ﻰﺼﻗأ ﺪﺤﻛ ﻢﻠﻣ
5 × 8
هزاﺪﻧا
ﺮﺘﻤﯿﻠﯿﻣ
8
ﺮﺜﮐاﺪﺣ
×
5
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
ﻢﺠﺤﻟا
ﻰﺼﻗأ ﺪﺤﻛ ﻢﻠﻣ
5 × 8
هزاﺪﻧا
ﺮﺘﻤﯿﻠﯿﻣ
8
ﺮﺜﮐاﺪﺣ
×
5
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
ﻢﺠﺤﻟا
ﻰﺼﻗأ ﺪﺤﻛ ﻢﻠﻣ
5 × 8
هزاﺪﻧا
ﺮﺘﻤﯿﻠﯿﻣ
8
ﺮﺜﮐاﺪﺣ
×
5
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
ﻢﺠﺤﻟا
ﻰﺼﻗأ ﺪﺤﻛ ﻢﻠﻣ
5 × 8
هزاﺪﻧا
ﺮﺘﻤﯿﻠﯿﻣ
8
ﺮﺜﮐاﺪﺣ
×
5
1
2
Face the hook inwards.
.ﻞﺧاﺪﻠﻟ ﺎًﻬﺠﺘﻣ فﺎﻄﺨﻟا ﻞﻌﺟا
.ﺪﯿﻫد راﺮﻗ ﻞﺧاد ﻪﺑ ور ار بﻼﻗ
A
B
Fuse (10 A)
(ﺮﻴﺒﻣأ
10
) ﺮﻬﺼﻨﻣ
(ﺮﭙﻣآ
10
) زﻮﯿﻓ
Front panel release button
ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺮﻳﺮﺤﺗ رز
ﻮﻠﺟ ﻪﺤﻔﺻ یزﺎﺳﺎﻫر ﻪﻤﮐد
Dashboard
تاداﺪﻌﻟا ﺔﺣﻮﻟ
درﻮﺒﺷاد
Claws
ﺐﻟﺎﺨﻣ
ﺎﻫ هﺮﯿﮔ
2
3
1
Catch
جﻻﺰﻣ
هﺮﯿﮔ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Firewall
ﻞﺼﻔﻟا راﺪﺟ
ﻦﯿﺸﺗآ راﻮﯾد
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
11
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), COVER
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1),
COVER
(Page
COVER
(Page
11)
3-3. SUB PANEL BLOCK
(Page
(Page
12)
3-4. CD MECHANISM DECK (MG-101CA-188)
(Page
(Page
12)
3-5. MAIN
BOARD
(Page
13)
SET
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
3-6. SERVO
BOARD
(Page
13)
3-7. CHASSIS (T) SUB ASSY
(Page
(Page
14)
3-8. ROLLER ARM ASSY
(Page
(Page
14)
3-9. CHASSIS
(OP)
ASSY
(Page
15)
3-11. SLED MOTOR ASSY
(Page
(Page
16)
3-12. OPTICAL PICK-UP SECTION
(Page
(Page
17)
3-13. OPTICAL PICK-UP
(Page
(Page
17)
3-10. CHUCKING ARM SUB ASSY
(Page
(Page
15)
2 two bosses
3 three claws
2 two bosses
4 cover
1 mini fuse (blade type) (10A/32V)
(FU1)
CDX-GT575UE/GT575UI/GT575UP/GT625UI/GT627UV
12
3-4. CD MECHANISM DECK (MG-101CA-188)
3-3. SUB PANEL BLOCK
2 two claws
2 two claws
3 sub panel block
1 two screws
(PTT2.6
u 6)
3 connector
(CN700)
1 screw
(PTT2.6
u 6)
1 screw
(PTT2.6
u 6)
2 Lift up the CD mechanism block.
6 CD mechanism deck
(MG-101CA-188)
4 two screws
(PTT2.6
u 4)
5 bracket (CD)
Click on the first or last page to see other CDX-GT575UE / CDX-GT575UI / CDX-GT575UP / CDX-GT625UI / CDX-GT627UV service manuals if exist.