Sony CDX-GT56UI Service Manual ▷ View online
CDX-GT56UI/GT56UIW
9
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
Note: Follow the disassembly procedure in the numerical order given.
3-1. SUB PANEL ASSY
2 two claws
3 two claws
4 sub panel assy
1 two screws
(+PTT 2.6
u 6)
3-1. SUB
PANEL
ASSY
(Page
9)
3-2.
CD MECHANISM BLOCK
(Page
10)
SET
3-3. MAIN
BOARD
(Page
10)
3-5.
CHASSIS (T) SUB ASSY
(Page
12)
3-6.
ROLLER ARM ASSY
(Page
12)
3-7. CHASSIS
(OP)
ASSY
(Page
13)
3-8.
CHUCKING ARM SUB ASSY
(Page
13)
3-9. SLED
MOTOR
ASSY
(Page
14)
3-10. OPTICAL PICK-UP SECTION
(Page
(Page
15)
3-11. OPTICAL
PICK-UP
(Page
15)
3-4. SERVO
BOARD
(Page
11)
CDX-GT56UI/GT56UIW
10
3-2. CD MECHANISM BLOCK
4 CN700
3
1 screw
(+PTT
2.6
u 6)
2 screw
(+PTT 2.6
u 6)
5 two screws
(+PTT
2.6
u 4)
6 bracket (CD)
7 CD mechanism block
3-3. MAIN BOARD
0 MAIN board
insulating sheet
3
2 two screws
(+PTT
2.6
u 8)
8 screw
(+PTT
2.6
u 10)
9 heat sink
7 screw
(+P
2.6
u 8)
5 screw
(+P
2.6
u 8)
6 two screws
(+PTT
2.6
u 10)
4 screw
(+PTT
2.6
u 10)
(GT56UI)
1 three ground point screws
(+PTT
2.6
u 6)
Note: When the complete MAIN board is replaced, the
destination setting is necessary. Refer to “NOTE
THE MAIN BOARD OR SYSTEM CONTROL-
LER (IC501) REPLACING” on page 4.
THE MAIN BOARD OR SYSTEM CONTROL-
LER (IC501) REPLACING” on page 4.
CDX-GT56UI/GT56UIW
11
3-4. SERVO BOARD
–
CD mechanism deck bottom side view
–
–
CD mechanism deck bottom side view
–
6 SERVO board
2 toothed lock screw
(M1.7
u 2.5)
5 optical pick-up (16 core)
(CN101)
2 toothed lock screw
(M1.7
u 2.5)
3 claw
4 claw
CD mechanism deck
SERVO board
1 Remove the eleven solders.
GRY
YEL
BLU
ORG
RED
BLK
RED
WHT
BLK
RED
WHT
6 SERVO board
3 claw
4 claw
SERVO board
2 toothed lock screw
(M1.7
u 2.5)
2 toothed lock screw
(M1.7
u 2.5)
1 Remove the eleven solders.
GRY
YEL
BLU
ORG
RED
BLK
RED
WHT
BLK
RED
WHT
5 optical pick-up (16 core)
(CN101)
CD mechanism deck
Note: In this unit, the complete SERVO board has been changed in the
midway of production. When replacing the complete SERVO
board, refer to “ABOUT THE MG-101CA-188 OF FORMER
AND NEW” on page 5.
board, refer to “ABOUT THE MG-101CA-188 OF FORMER
AND NEW” on page 5.
• Former type
• New type
Ver. 1.2
CDX-GT56UI/GT56UIW
12
3-5. CHASSIS (T) SUB ASSY
3-6. ROLLER ARM ASSY
4 chassis (T) sub assy
3 claw
1 two screws
(M 1.7
u 2.5)
2 two screws
(M
1.7
u 2.5)
3 washer
4 gear (HRA)
6 roller arm assy
5
1 spring (RAL)
2 spring (RAR)
Click on the first or last page to see other CDX-GT56UI service manuals if exist.