Sony CDX-G1000U / CDX-G1000UE / CDX-G1001U / CDX-G1002U / CDX-G1050U / CDX-G1050UE / CDX-G1051U / CDX-G1070U / CDX-G1071U / CDX-G1080UM Service Manual ▷ View online
CDX-G1000U/G1000UE/G1001U/G1002U/G1050U/G1050UE/G1051U/G1070U/G1071U/G1080UM
5
TEST DISCS
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Part No.
Description
3-702-101-01 DISC
(YEDS-18),
TEST
4-225-203-01 DISC
(PATD-012),
TEST
NOTE OF REPLACING THE KEY BOARD
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
NOTE OF REPLACING THE IC1301 ON THE MAIN BOARD
IC1301 on the MAIN board cannot replace with single. When this
part is damaged, replace the complete mounted board.
IC1301 on the MAIN board cannot replace with single. When this
part is damaged, replace the complete mounted board.
1-4. Destination Code
Model
Destination OP5 OP4 OP3 OP2 OP1 OP0
CDX-G1000U
AEP, UK
0
0
1
0
0
1
Russian
8
0
1
0
0
1
CDX-G1000UE
Russian
8
0
1
0
0
7
CDX-G1001U
AEP, UK
0
0
1
0
0
1
CDX-G1002U
AEP, UK
0
0
1
0
0
1
CDX-G1050U
E, Mexican,
Korean
Korean
0
0
1
8
0
0
Saudi Arabia
0
0
1
8
0
4
Argentina
0
0
5
8
0
3
CDX-G1050UE
Russian
8
0
1
0
0
7
CDX-G1051U
E, Korean
0
0
1
8
0
0
Saudi Arabia
0
0
1
8
0
4
CDX-G1070U
Indian
1
0
1
8
0
0
CDX-G1071U
Indian
1
0
1
8
0
0
CDX-G1080UM
Indian
1
0
1
8
0
0
2. Confi rmation After Destination Setting
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Destination setting checking method:
1. In the state of source off (the clock is displayed on the liquid
1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons in
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
[PAUSE 6] button for two seconds).
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following fi gure), enter
the destination setting value display mode by pressing the [
the destination setting value display mode by pressing the [
SCRL DSPL] button.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
System controller version
SHUF
3. Confi rm the alphanumeric character of 12 digits in liquid crys-
tal display is an value correctly input.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Destination code
12 digit
OP5 OP4 OP3 OP2 OP1 OP0
SHUF
4. The resetting operation is executed by pressing the [
OFF
SRC] button for 1 second after the confi rming ends, and the
unit returns to the normal condition.
unit returns to the normal condition.
Replacing the lithium battery of the
remote commander
remote commander
(CDX-G1050U/G1050UE/G1051U/G1070U/G1071U/G1080UM
only)
only)
When the battery becomes weak, the range
of the remote commander becomes shorter.
Replace the battery with a new CR2025
lithium battery. Use of any other battery may
present a risk of fire or explosion.
of the remote commander becomes shorter.
Replace the battery with a new CR2025
lithium battery. Use of any other battery may
present a risk of fire or explosion.
Notes on the lithium battery
ˎ Keep the lithium battery out of the reach of
ˎ Keep the lithium battery out of the reach of
children. Should the battery be swallowed,
immediately consult a doctor.
immediately consult a doctor.
ˎ Wipe the battery with a dry cloth to assure a good
contact.
ˎ Be sure to observe the correct polarity when
installing the battery.
ˎ Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
Cleaning the connectors
The unit may not function properly if the
connectors between the unit and the front
panel are not clean. In order to prevent this,
detach the front panel (page 5) and clean the
connectors with a cotton swab. Do not apply
too much force. Otherwise, the connectors
may be damaged.
connectors between the unit and the front
panel are not clean. In order to prevent this,
detach the front panel (page 5) and clean the
connectors with a cotton swab. Do not apply
too much force. Otherwise, the connectors
may be damaged.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose
of in fire.
Do not recharge, disassemble, or dispose
of in fire.
+ side up
Notes
ˎ For safety, turn off the ignition before cleaning
ˎ For safety, turn off the ignition before cleaning
the connectors, and remove the key from the
ignition switch.
ignition switch.
ˎ Never touch the connectors directly with your
fingers or with any metal device.
and clean the
Ver. 1.2
CDX-G1000U/G1000UE/G1001U/G1002U/G1050U/G1050UE/G1051U/G1070U/G1071U/G1080UM
6
SERVICE POSITION
CD mechanism deck
CD mechanism deck
insulating sheet
insulating sheet
stand
stand
main unit
main unit
cable flexible flat (27 core)
Note: Do not cable flexible flat (27 core) is
Note: Do not cable flexible flat (27 core) is
damaged by the edge of the chassis.
cable flexible flat (27 core)
Note: Do not cable flexible flat (27 core) is
Note: Do not cable flexible flat (27 core) is
damaged by the edge of the chassis.
OK
OK
main unit
main unit
cable flexible flat (27 core)
cable flexible flat (27 core)
CD mechanism deck
Note: CD mechanical deck should
Note: CD mechanical deck should
not be placed vertically.
CD mechanism deck
Note: CD mechanical deck should
Note: CD mechanical deck should
not be placed vertically.
NG
main unit
cable flexible flat (27 core)
CD mechanism deck
Note: CD mechanical deck should
Note: CD mechanical deck should
not be placed upside down.
NG
NG
CDX-G1000U/G1000UE/G1001U/G1002U/G1050U/G1050UE/G1051U/G1070U/G1071U/G1080UM
7
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
(AEP and UK models)
A
B
C
*
Preparation of the rear speaker cords is required.
Die Kabel für die Hecklautsprecher müssen vorbereitet werden.
Il est nécessaire de préparer les cordons du haut-parleur arrière.
È necessario preparare i cavi del diffusore posteriore.
De snoeren van de achterluidspreker moeten worden voorbereid.
Die Kabel für die Hecklautsprecher müssen vorbereitet werden.
Il est nécessaire de préparer les cordons du haut-parleur arrière.
È necessario preparare i cavi del diffusore posteriore.
De snoeren van de achterluidspreker moeten worden voorbereid.
Voorbeeldaansluitingen (
)
Eenvoudige aansluiting van subwoofer (ǵ-C)
U kunt een subwoofer zonder versterker gebruiken
wanneer deze verbonden is met een
achterluidsprekerkabel.
U kunt een subwoofer zonder versterker gebruiken
wanneer deze verbonden is met een
achterluidsprekerkabel.
Opmerking
Sluit een subwoofer van 4 - 8 ohm aan. Sluit geen luidspreker aan op
de andere achterluidsprekerkabel.
Sluit een subwoofer van 4 - 8 ohm aan. Sluit geen luidspreker aan op
de andere achterluidsprekerkabel.
* Sluit geen luidspreker aan in deze verbinding.
Opmerkingen
ˎ Sluit eerst de aarddraad aan voordat u de versterker aansluit.
ˎ U hoort de pieptoon alleen als de ingebouwde versterker wordt
gebruikt.
Aansluitschema (
)
Waarschuwing
Indien u een elektrische antenne hebt zonder
relaiskast, kan het aansluiten van dit apparaat met de
bijgeleverde voedingskabel ʔ de antenne
beschadigen.
relaiskast, kan het aansluiten van dit apparaat met de
bijgeleverde voedingskabel ʔ de antenne
beschadigen.
Opmerkingen over de bedienings- en voedingskabels
ˎ De REM OUT-kabel (blauw/wit gestreept) levert +12 V DC als u het
apparaat inschakelt.
ˎ Als u een optionele versterker gebruikt, sluit u de REM OUT-kabel
(blauw/wit gestreept) of de voedingskabel voor accessoires (rood)
aan op de AMP REMOTE IN-aansluiting van de versterker.
aan op de AMP REMOTE IN-aansluiting van de versterker.
ˎ Als uw auto uitgerust is met een FM/MW/LW-antenne in de
achter- of zijruit, sluit u de REM OUT-kabel (blauw/wit gestreept) of
de voedingskabel voor accessoires (rood) aan op de
voedingsaansluiting van de bestaande antenneversterker.
Contacteer uw handelaar voor meer informatie.
de voedingskabel voor accessoires (rood) aan op de
voedingsaansluiting van de bestaande antenneversterker.
Contacteer uw handelaar voor meer informatie.
ˎ Met dit apparaat is het niet mogelijk een elektrische antenne
zonder relaiskast te gebruiken.
Instandhouden van het geheugen
Zolang de gele voedingskabel is aangesloten, blijft de
stroomvoorziening van het geheugen intact, ook wanneer het
contact van de auto wordt uitgeschakeld.
Zolang de gele voedingskabel is aangesloten, blijft de
stroomvoorziening van het geheugen intact, ook wanneer het
contact van de auto wordt uitgeschakeld.
Opmerkingen betreffende het aansluiten van de luidsprekers
ˎ Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers
aan te sluiten.
ˎ Gebruik luidsprekers met een impedantie van 4 tot 8 ohm en let op
dat die het vermogen van de versterker kunnen verwerken. Als u dit
niet doet, kunnen de luidsprekers ernstig beschadigd raken.
niet doet, kunnen de luidsprekers ernstig beschadigd raken.
ˎ Verbind in geen geval de aansluitingen van de luidsprekers met het
chassis van de auto en sluit de aansluitingen van de rechter- en
linkerluidspreker niet op elkaar aan.
linkerluidspreker niet op elkaar aan.
ˎ Verbind de aarddraad van dit apparaat niet met de negatieve (–)
aansluiting van de luidspreker.
ˎ Probeer nooit de luidsprekers parallel aan te sluiten.
ˎ Sluit geen actieve luidsprekers (met ingebouwde versterkers) aan
op de luidsprekeraansluiting van dit apparaat. Dit zal leiden tot
beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend
luidsprekers zonder ingebouwde versterker aan.
beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend
luidsprekers zonder ingebouwde versterker aan.
ˎ Om defecten te vermijden mag u de bestaande
luidsprekerbedrading in uw auto niet gebruiken wanneer er een
gemeenschappelijke negatieve (–) draad is voor de rechter- en
linkerluidsprekers.
gemeenschappelijke negatieve (–) draad is voor de rechter- en
linkerluidsprekers.
ˎ Verbind de luidsprekerdraden niet met elkaar.
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
ʔ
from the car’s power connector
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsaansluiting
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsaansluiting
See “Power connection diagram (ǻ)” on the reverse side for
details.
details.
Näheres dazu finden Sie im „Stromanschlussdiagramm (ǻ) “.
Blättern Sie dazu bitte um.
Blättern Sie dazu bitte um.
Voir le « Schéma de raccordement d’alimentation (ǻ) » au verso
pour plus de détails.
pour plus de détails.
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
alimentazione (ǻ)” che si trova sul retro.
alimentazione (ǻ)” che si trova sul retro.
Zie "Voedingsaansluitschema (ǻ)" op de achterkant voor meer
details.
details.
from the car’s speaker connector
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore dei diffusori dell’auto
van de autoluidsprekeraansluiting
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore dei diffusori dell’auto
van de autoluidsprekeraansluiting
*
1
from car antenna
(aerial)
von Autoantenne
de l’antenne de la
voiture
dall’antenna
dell’auto
van een
auto-antenne
von Autoantenne
de l’antenne de la
voiture
dall’antenna
dell’auto
van een
auto-antenne
*
4
*
2
*
2
*
1
Depending on the type of car, use an adaptor (not
supplied) if the antenna connector does not fit.
*
2
RCA pin cord (not supplied).
*
3
Separate adaptor may be required.
*
4
Speaker impedance: 4 – 8 ohms × 4
*
1
Abhängig vom Autotyp müssen Sie einen Adapter
(nicht mitgeliefert) verwenden, wenn der
Antennenanschluss nicht passt.
Antennenanschluss nicht passt.
*
2
Cinchkabel (nicht mitgeliefert).
*
3
Möglicherweise ist ein separater Adapter
erforderlich.
*
4
Lautsprecherimpedanz: 4 – 8 Ohm × 4
*
1
Selon le type de voiture, utilisez un adaptateur (non
fourni) si le connecteur de l’antenne ne convient
pas.
pas.
*
2
Cordon à broche RCA (non fourni).
*
3
Un adaptateur séparé peut être nécessaire.
*
4
Impédance des haut-parleurs : 4 – 8 ohms × 4
*
1
In base al tipo di automobile, utilizzare un
adattatore (non in dotazione) nel caso in cui il
connettore dell'antenna non sia adatto.
connettore dell'antenna non sia adatto.
*
2
Cavo a piedini RCA (non in dotazione).
*
3
Potrebbe essere necessario un adattatore separato.
*
4
Impedenza diffusori: 4 – 8 ohm × 4
*
1
Afhankelijk van het soort wagen gebruikt u een
adapter (niet bijgeleverd) als de antenneconnector
niet past.
niet past.
*
2
Tulpstekkersnoer (niet bijgeleverd).
*
3
Er is mogelijk een afzonderlijke adapter vereist.
*
4
Luidsprekerimpedantie: 4 – 8 ohm × 4
Negative polarity positions 2, 4, 6, and 8 have striped leads.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
1
Purple
Violett
Violet
Viola
Paars
Violett
Violet
Viola
Paars
+
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
2
–
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
3
Gray
Grau
Gris
Grigio
Grijs
Grau
Gris
Grigio
Grijs
+
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
4
–
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
5
White
Weiß
Blanc
Bianco
Wit
Weiß
Blanc
Bianco
Wit
+
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
6
–
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
7
Green
Grün
Vert
Verde
Groen
Grün
Vert
Verde
Groen
+
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
8
–
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Equipment used in illustrations (not supplied)
In Abbildungen dargestellte Geräte (nicht mitgeliefert)
Appareils utilisés dans les illustrations (non fournis)
Apparecchiatura utilizzata nelle illustrazioni (non in dotazione)
Apparatuur gebruikt in de afbeeldingen (niet bijgeleverd)
In Abbildungen dargestellte Geräte (nicht mitgeliefert)
Appareils utilisés dans les illustrations (non fournis)
Apparecchiatura utilizzata nelle illustrazioni (non in dotazione)
Apparatuur gebruikt in de afbeeldingen (niet bijgeleverd)
Front speaker
Frontlautsprecher
Haut-parleur avant
Diffusore anteriore
Voorluidspreker
Frontlautsprecher
Haut-parleur avant
Diffusore anteriore
Voorluidspreker
Rear speaker
Hecklautsprecher
Haut-parleur arrière
Diffusore posteriore
Achterluidspreker
Hecklautsprecher
Haut-parleur arrière
Diffusore posteriore
Achterluidspreker
Subwoofer
Tiefsttonlautsprecher
Caisson de graves
Subwoofer
Subwoofer
Tiefsttonlautsprecher
Caisson de graves
Subwoofer
Subwoofer
Power amplifier
Endverstärker
Amplificateur de puissance
Amplificatore di potenza
Eindversterker
Endverstärker
Amplificateur de puissance
Amplificatore di potenza
Eindversterker
Positions 1, 2, 3 and 6 do not have pins.
An Position 1, 2, 3 und 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
An Position 1, 2, 3 und 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
4
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
5
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
power antenna (aerial) /power amplifier control (REM OUT)
Steueranschluss für Motorantenne/Endverstärker (REM OUT)
commande de l’antenne électrique/amplificateur de puissance (REM
OUT)
antenna elettrica/controllo dell’amplificatore di potenza (REM OUT)
elektrische antenne / versterker (REM OUT)
Steueranschluss für Motorantenne/Endverstärker (REM OUT)
commande de l’antenne électrique/amplificateur de puissance (REM
OUT)
antenna elettrica/controllo dell’amplificatore di potenza (REM OUT)
elektrische antenne / versterker (REM OUT)
7
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
8
Black
Schwarz
Noir
Nero
Zwart
Schwarz
Noir
Nero
Zwart
ground (earth)
Masse
masse
terra
aarding
Masse
masse
terra
aarding
English
Cautions
ˎ This unit is designed for negative ground (earth) 12 V
DC operation only.
ˎ Do not get the leads under a screw, or caught in
moving parts (e.g. seat railing).
ˎ Before making connections, turn the car ignition off
to avoid short circuits.
ˎ Connect the power supply lead ʔ to the unit and
speakers before connecting it to the auxiliary power
connector.
connector.
ˎ Run all ground (earth) leads to a common ground
(earth) point.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
Notes on the power supply lead (yellow)
ˎ When connecting this unit in combination with other
stereo components, the connected car circuit’s
rating must be higher than the sum of each
component’s fuse.
rating must be higher than the sum of each
component’s fuse.
ˎ When no car circuits are rated high enough, connect
the unit directly to the battery.
Connection example (
)
Subwoofer Easy Connection (ǵ-C)
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
Note
Be sure to connect a 4 - 8 ohm subwoofer. Do not connect a speaker
to the other rear speaker cord.
Be sure to connect a 4 - 8 ohm subwoofer. Do not connect a speaker
to the other rear speaker cord.
* Do not connect a speaker in this connection.
Notes
ˎ Be sure to connect the ground (earth) lead before connecting the
amplifier.
ˎ The alarm will only sound if the built-in amplifier is used.
Connection diagram (
)
Warning
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
box, connecting this unit with the supplied power
supply lead ʔ may damage the antenna (aerial).
Notes on the control and power supply leads
ˎ REM OUT lead (blue/white striped) supplies +12 V DC when you turn
on the unit.
ˎ When using an optional power amplifier, connect REM OUT lead
(blue/white striped) or the accessory power supply lead (red) to its
AMP REMOTE IN.
AMP REMOTE IN.
ˎ When your car has built-in FM/MW/LW antenna (aerial) in the rear/
side glass, connect REM OUT lead (blue/white striped) or the
accessory power supply lead (red) to the power terminal of the
existing antenna (aerial) booster. For details, consult your dealer.
accessory power supply lead (red) to the power terminal of the
existing antenna (aerial) booster. For details, consult your dealer.
ˎ A power antenna (aerial) without a relay box cannot be used with
this unit.
Memory hold connection
When the yellow power supply lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
When the yellow power supply lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
ˎ Do not connect the speaker terminals to the car chassis, or connect
the terminals of the right speakers with those of the left speaker.
ˎ Do not connect the ground (earth) lead of this unit to the negative
(–) terminal of the speaker.
ˎ Do not attempt to connect the speakers in parallel.
ˎ Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
ˎ To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
for the right and left speakers.
ˎ Do not connect the unit’s speaker leads to each other.
Deutsch
Warnhinweise
ˎ Dieses Gerät ist ausschließlich für den Betrieb bei
12 V Gleichstrom (negative Erdung) bestimmt.
ˎ Achten Sie darauf, dass die Kabel nicht unter einer
Schraube oder zwischen beweglichen Teilen wie
z. B. in einer Sitzschiene eingeklemmt werden.
z. B. in einer Sitzschiene eingeklemmt werden.
ˎ Schalten Sie, bevor Sie irgendwelche Anschlüsse
vornehmen, die Zündung des Fahrzeugs aus, um
Kurzschlüsse zu vermeiden.
Kurzschlüsse zu vermeiden.
ˎ Verbinden Sie das Stromversorgungskabel ʔ mit
dem Gerät und den Lautsprechern, bevor Sie es mit
dem Hilfsstromanschluss verbinden.
dem Hilfsstromanschluss verbinden.
ˎ Schließen Sie alle Erdungskabel an einen
gemeinsamen Massepunkt an.
ˎ Aus Sicherheitsgründen müssen alle losen, nicht
angeschlossenen Drähte mit Isolierband abgeklebt
werden.
werden.
Hinweise zum Stromversorgungskabel (gelb)
ˎ Wenn Sie dieses Gerät zusammen mit anderen
Stereokomponenten anschließen, muss der
Autostromkreis, an den die Geräte angeschlossen
sind, eine höhere Leistung aufweisen als die Summe
der Sicherungen der einzelnen Komponenten.
Autostromkreis, an den die Geräte angeschlossen
sind, eine höhere Leistung aufweisen als die Summe
der Sicherungen der einzelnen Komponenten.
ˎ Wenn kein Autostromkreis eine so hohe Leistung
aufweist, schließen Sie das Gerät direkt an die
Batterie an.
Batterie an.
Anschlussbeispiel (
)
Einfache Verbindung Tiefsttonlautsprecher (ǵ-C)
Sie können einen Tiefsttonlautsprecher ohne einen
Endverstärker verwenden, wenn er an ein
Hecklautsprecherkabel angeschlossen ist.
Sie können einen Tiefsttonlautsprecher ohne einen
Endverstärker verwenden, wenn er an ein
Hecklautsprecherkabel angeschlossen ist.
Hinweis
Achten Sie darauf, einen Tiefsttonlautsprecher mit 4 - 8 Ohm
anzuschließen. Schließen Sie keinen Lautsprecher an das andere
Hecklautsprecherkabel an.
Achten Sie darauf, einen Tiefsttonlautsprecher mit 4 - 8 Ohm
anzuschließen. Schließen Sie keinen Lautsprecher an das andere
Hecklautsprecherkabel an.
* Schließen Sie an diesen Anschluss keinen Lautsprecher an.
Hinweise
ˎ Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie den
Verstärker anschließen.
ˎ Der Warnton wird nur ausgegeben, wenn der integrierte Verstärker
verwendet wird.
Anschlussdiagramm (
)
Warnung
Wenn Sie eine Motorantenne ohne Relaiskästchen
verwenden, kann durch Anschließen dieses Geräts mit
dem mitgelieferten Stromversorgungskabel ʔ die
Antenne beschädigt werden.
verwenden, kann durch Anschließen dieses Geräts mit
dem mitgelieferten Stromversorgungskabel ʔ die
Antenne beschädigt werden.
Hinweise zu den Steuer- und Stromversorgungsleitungen
ˎ Die REM OUT-Leitung (blauweiß gestreift) liefert +12 V Gleichstrom,
wenn Sie das Gerät einschalten.
ˎ Wenn Sie einen gesondert erhältlichen Endverstärker verwenden,
schließen Sie die REM OUT-Leitung (blauweiß gestreift) oder die
Stromversorgungsleitung für Zubehörgeräte (rot) an AMP REMOTE
IN an.
Stromversorgungsleitung für Zubehörgeräte (rot) an AMP REMOTE
IN an.
ˎ Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe
integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schließen
Sie die REM OUT-Leitung (blauweiß gestreift) oder die
Stromversorgungsleitung für Zubehörgeräte (rot) an den
Stromversorgungsanschluss des vorhandenen Antennenverstärkers
an. Einzelheiten dazu erhalten Sie bei Ihrem Händler.
Sie die REM OUT-Leitung (blauweiß gestreift) oder die
Stromversorgungsleitung für Zubehörgeräte (rot) an den
Stromversorgungsanschluss des vorhandenen Antennenverstärkers
an. Einzelheiten dazu erhalten Sie bei Ihrem Händler.
ˎ Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen
werden.
Stromversorgung des Speichers
Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der
Speicher stets (auch bei ausgeschalteter Zündung) mit Strom
versorgt.
Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der
Speicher stets (auch bei ausgeschalteter Zündung) mit Strom
versorgt.
Hinweise zum Lautsprecheranschluss
ˎ Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen.
ˎ Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8
Ohm und ausreichender Belastbarkeit. Ansonsten können die
Lautsprecher beschädigt werden.
Lautsprecher beschädigt werden.
ˎ Verbinden Sie die Lautsprecheranschlüsse nicht mit dem
Wagenchassis und verbinden Sie auch nicht die Anschlüsse des
rechten mit denen des linken Lautsprechers.
rechten mit denen des linken Lautsprechers.
ˎ Verbinden Sie die Masseleitung dieses Geräts nicht mit dem
negativen (–) Lautsprecheranschluss.
ˎ Versuchen Sie nicht, Lautsprecher parallel anzuschließen.
ˎ An die Lautsprecheranschlüsse dieses Geräts dürfen nur
Passivlautsprecher angeschlossen werden. Schließen Sie keine
Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an,
Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an,
Français
Précautions
ˎ Cet appareil est conçu pour fonctionner uniquement
sur un courant continu de 12 V avec masse négative.
ˎ Evitez de coincer les câbles sous des vis ou dans des
pièces mobiles (par exemple, armature de siège).
ˎ Avant d’effectuer des raccordements, éteignez le
moteur pour éviter les courts-circuits.
ˎ Branchez le câble d’alimention ʔ sur l’appareil et les
haut-parleurs avant de le brancher sur le connecteur
d’alimentation auxiliaire.
d’alimentation auxiliaire.
ˎ Rassemblez tous les câbles de mise à la masse en
un point de masse commun.
ˎ Veillez à isoler tout câble lâche non raccordé avec du
ruban isolant.
Remarques sur le câble d’alimentation (jaune)
ˎ Lorsque cet appareil est raccordé à d’autres
équipements stéréo, la valeur nominale du circuit
raccordé du véhicule doit être supérieure à la
somme des fusibles de chaque élément.
raccordé du véhicule doit être supérieure à la
somme des fusibles de chaque élément.
ˎ Si aucun circuit de la voiture n’est assez puissant,
raccordez directement l’appareil à la batterie.
da das Gerät sonst beschädigt werden könnte.
ˎ Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im
Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn
am Ende eine gemeinsame negative (–) Leitung für den rechten
und den linken Lautsprecher verwendet wird.
am Ende eine gemeinsame negative (–) Leitung für den rechten
und den linken Lautsprecher verwendet wird.
ˎ Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander.
Exemple de raccordement (
)
Raccordement aisé d’un caisson de graves (ǵ-C)
Vous pouvez utiliser un caisson de graves sans
amplificateur de puissance lorsqu’il est raccordé à un
cordon de haut-parleur arrière.
Vous pouvez utiliser un caisson de graves sans
amplificateur de puissance lorsqu’il est raccordé à un
cordon de haut-parleur arrière.
Remarque
Veillez à raccorder un caisson de graves de 4 - 8 ohms. Ne raccordez
pas un haut-parleur à l’autre cordon de haut-parleur arrière.
Veillez à raccorder un caisson de graves de 4 - 8 ohms. Ne raccordez
pas un haut-parleur à l’autre cordon de haut-parleur arrière.
* Ne raccordez pas de haut-parleur à cette connexion.
Remarques
ˎ Raccordez d’abord le câble de mise à la masse avant de connecter
l’amplificateur.
Italiano
Attenzione
ˎ Questo apparecchio è stato progettato per l’uso solo
a 12 V CC con massa negativa.
ˎ Evitare che i cavi rimangano bloccati da una vite o
incastrati nelle parti mobili (ad esempio nelle guide
scorrevoli dei sedili).
scorrevoli dei sedili).
ˎ Prima di effettuare i collegamenti, spegnere il
motore dell’automobile onde evitare di causare
cortocircuiti.
cortocircuiti.
ˎ Collegare il cavo di alimentazione ʔ all’apparecchio
e ai diffusori prima di collegarlo al connettore di
alimentazione ausiliaria.
alimentazione ausiliaria.
ˎ Portare tutti i cavi di messa a terra a un punto di
massa comune.
ˎ Per sicurezza, assicurarsi di isolare qualsiasi cavo
non collegato utilizzando del nastro adesivo.
ˎ L’alarme est émise uniquement lorsque l’amplificateur intégré est
utilisé.
Schéma de raccordement (
)
Avertissement
Si vous disposez d’une antenne électrique sans boîtier
de relais, le branchement de cet appareil au moyen du
cordon d’alimentation fourni ʔ risque d’endommager
l’antenne.
de relais, le branchement de cet appareil au moyen du
cordon d’alimentation fourni ʔ risque d’endommager
l’antenne.
Remarques sur les câbles de commande et d’alimentation
ˎ Fil REM OUT (rayé bleu/blanc) fournit une tension de +12 V CC lors
de la mise sous tension de l’appareil.
ˎ Si vous utilisez un amplificateur de puissance en option, raccordez
le fil REM OUT (rayé bleu/blanc) ou le fil d’alimentation des
accessoires (rouge) à son AMP REMOTE IN.
accessoires (rouge) à son AMP REMOTE IN.
ˎ Si votre véhicule est équipé d’une antenne FM/MW (PO)/LW (GO)
intégrée dans la vitre arrière/latérale, raccordez le fil REM OUT (rayé
bleu/blanc) ou le fil d’alimentation des accessoires (rouge) à la
borne d’alimentation de l’amplificateur d’antenne existant. Pour
plus d’informations, consultez votre revendeur.
bleu/blanc) ou le fil d’alimentation des accessoires (rouge) à la
borne d’alimentation de l’amplificateur d’antenne existant. Pour
plus d’informations, consultez votre revendeur.
ˎ Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est raccordé, le circuit de la
mémoire est alimenté en permanence même si la clé de contact est
en position d’arrêt.
Lorsque le câble d’alimentation jaune est raccordé, le circuit de la
mémoire est alimenté en permanence même si la clé de contact est
en position d’arrêt.
Remarques sur le raccordement des haut-parleurs
ˎ Avant de raccorder les haut-parleurs, mettre l’appareil hors tension.
ˎ Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et
une capacité adéquate sous peine de les endommager.
ˎ Ne pas raccorder les bornes du système de haut-parleurs au châssis
de la voiture et ne pas connecter les bornes des haut-parleurs droit
à celles des haut-parleurs gauche.
à celles des haut-parleurs gauche.
ˎ Ne pas raccorder le câble de mise à la masse de cet appareil à la
borne négative (–) du haut-parleur.
ˎ Ne pas tenter de raccorder les haut-parleurs en parallèle.
ˎ Connecter uniquement des haut-parleurs passifs. La connexion de
haut-parleurs actifs (avec des amplificateurs intégrés) aux bornes
des haut-parleurs pourrait endommager l’appareil.
des haut-parleurs pourrait endommager l’appareil.
ˎ Pour éviter tout problème de fonctionnement, ne pas utileser les
câbles des haut-parleurs intégrés (–) installés dans votre voiture si
l’appareil dispose d’un câble négatif commun pour les
haut-parleurs droit et gauche.
l’appareil dispose d’un câble négatif commun pour les
haut-parleurs droit et gauche.
ˎ Ne pas raccorder entre eux les cordons des haut-parleurs de
l’appareil.
Esempio di collegamento (
)
Collegamento semplice del subwoofer (ǵ-C)
Se collegato a un cavo del diffusore posteriore, è
possibile utilizzare un subwoofer senza amplificatore
di potenza.
Se collegato a un cavo del diffusore posteriore, è
possibile utilizzare un subwoofer senza amplificatore
di potenza.
Nota
Accertarsi di collegare un subwoofer da 4 - 8 ohm. Non collegare un
diffusore all’altro cavo del diffusore posteriore.
Accertarsi di collegare un subwoofer da 4 - 8 ohm. Non collegare un
diffusore all’altro cavo del diffusore posteriore.
* Non collegare un diffusore in questa connessione.
Note
ˎ Assicurarsi di collegare il cavo di terra prima di collegare
l’apparecchio all’amplificatore.
ˎ L’allarme viene emesso solo se è in uso l’amplificatore incorporato.
Schema di collegamento (
)
Avvertenza
Quando si collega l’apparecchio con il cavo di
alimentazione in dotazione ʔ, si potrebbe
danneggiare l’antenna elettrica se questa non dispone
di scatola a relè.
alimentazione in dotazione ʔ, si potrebbe
danneggiare l’antenna elettrica se questa non dispone
di scatola a relè.
Note sui cavi di controllo e di alimentazione
ˎ Il cavo REM OUT (rigato blu e bianco) fornisce alimentazione da
+12 V CC all’accensione dell’apparecchio.
ˎ Quando si utilizza un amplificatore di potenza opzionale, collegare
il cavo REM OUT (rigato blu e bianco) o il cavo di alimentazione
accessoria (rosso) al rispettivo AMP REMOTE IN.
accessoria (rosso) al rispettivo AMP REMOTE IN.
ˎ Se l’automobile è dotata di antenna FM/MW/LW incorporata nel
vetro posteriore/laterale, collegare il cavo REM OUT (rigato blu e
bianco) o il cavo di alimentazione accessoria (rosso) al terminale di
alimentazione del preamplificatore dell’antenna esistente. Per
ulteriori informazioni, consultare il rivenditore.
bianco) o il cavo di alimentazione accessoria (rosso) al terminale di
alimentazione del preamplificatore dell’antenna esistente. Per
ulteriori informazioni, consultare il rivenditore.
ˎ Non è possibile usare un’antenna elettrica senza scatola a relè con
questo apparecchio.
Note sul cavo di alimentazione (giallo)
ˎ Se questo apparecchio viene collegato in
combinazione con altri componenti stereo, la
potenza nominale dei circuiti dell’automobile deve
essere superiore a quella prodotta dalla somma dei
fusibili di ciascun componente.
potenza nominale dei circuiti dell’automobile deve
essere superiore a quella prodotta dalla somma dei
fusibili di ciascun componente.
ˎ Se la potenza nominale dei circuiti dell’automobile
non è sufficiente, collegare l’apparecchio
direttamente alla batteria.
direttamente alla batteria.
Nederlands
Let op
ˎ Dit apparaat is ontworpen voor gebruik op een
auto-accu van 12 V gelijkstroom, negatieve aarde.
ˎ Zorg ervoor dat de draden niet onder een schroef of
tussen bewegende onderdelen (bv. rail van de
autostoel) terechtkomen.
autostoel) terechtkomen.
ˎ Voordat u de aansluitingen maakt, moet u het
contact uitzetten om kortsluiting te vermijden.
ˎ Sluit de voedingskabel ʔ aan op het apparaat en de
luidsprekers voordat u de kabel aansluit op de
hulpvoedingsaansluiting.
hulpvoedingsaansluiting.
ˎ Sluit alle aardingskabels op een
gemeenschappelijk aardpunt aan.
ˎ Voorzie niet-aangesloten kabels om
veiligheidsredenen altijd van isolatietape.
Opmerkingen bij de voedingskabel (geel)
ˎ Wanneer u dit apparaat aansluit samen met andere
componenten, moet het vermogen van de
aangesloten autostroomkring groter zijn dan de som
van de zekeringen van elke component afzonderlijk.
aangesloten autostroomkring groter zijn dan de som
van de zekeringen van elke component afzonderlijk.
ˎ Wanneer het vermogen ontoereikend is, moet u het
apparaat rechtstreeks aansluiten op de accu.
Collegamento per la conservazione della memoria
Quando il cavo di ingresso alimentazione giallo è collegato, viene
sempre fornita alimentazione al circuito di memoria anche quando
l’interruttore di accensione è spento.
Quando il cavo di ingresso alimentazione giallo è collegato, viene
sempre fornita alimentazione al circuito di memoria anche quando
l’interruttore di accensione è spento.
Note sul collegamento dei diffusori
ˎ Prima di collegare i diffusori spegnere l’apparecchio.
ˎ Usare diffusori di impedenza compresa tra 4 e 8 ohm e con
capacità di potenza adeguata, altrimenti i diffusori potrebbero
venire danneggiati.
venire danneggiati.
ˎ Non collegare i terminali del sistema diffusori al telaio dell’auto e
non collegare i terminali del diffusore destro a quelli del diffusore
sinistro.
sinistro.
ˎ Non collegare il cavo di terra di questo apparecchio al terminale
negativo (–) del diffusore.
ˎ Non collegare i diffusori in parallelo.
ˎ Assicurarsi di collegare soltanto diffusori passivi, poiché il
collegamento di diffusori attivi, dotati di amplificatori incorporati, ai
terminali dei diffusori potrebbe danneggiare l’apparecchio.
terminali dei diffusori potrebbe danneggiare l’apparecchio.
ˎ Per evitare problemi di funzionamento, non utilizzare i cavi dei
diffusori incorporati installati nell’automobile se l’apparecchio
condivide un cavo comune negativo (–) per i diffusori destro e
sinistro.
condivide un cavo comune negativo (–) per i diffusori destro e
sinistro.
ˎ Non collegare fra loro i cavi dei diffusori dell’apparecchio.
CDX-G1000U/G1000UE/G1001U/G1002U/G1050U/G1050UE/G1051U/G1070U/G1071U/G1080UM
8
Abnehmen und Anbringen der
Frontplatte (
Frontplatte (
)
Nehmen Sie die Frontplatte vor dem Einbau des
Geräts ab.
Geräts ab.
ǹ-A Abnehmen
Halten Sie vor dem Abnehmen der Frontplatte
unbedingt OFF gedrückt. Drücken Sie die Taste zum
Lösen der Frontplatte und ziehen Sie die Frontplatte
auf sich zu und heraus.
unbedingt OFF gedrückt. Drücken Sie die Taste zum
Lösen der Frontplatte und ziehen Sie die Frontplatte
auf sich zu und heraus.
ǹ-B Anbringen
Setzen Sie Teil ʭ der Frontplatte wie in der Abbildung
dargestellt an Teil ʮ des Geräts an und drücken Sie
die linke Seite der Frontplatte an, bis sie mit einem
Klicken einrastet.
dargestellt an Teil ʮ des Geräts an und drücken Sie
die linke Seite der Frontplatte an, bis sie mit einem
Klicken einrastet.
Warnhinweis, wenn die Zündung
Ihres Fahrzeugs nicht über eine
Zubehörposition (ACC oder I)
verfügt
Ihres Fahrzeugs nicht über eine
Zubehörposition (ACC oder I)
verfügt
Aktivieren Sie unbedingt die Abschaltautomatik.
Näheres dazu finden Sie in der mitgelieferten
Bedienungsanleitung.
Nach dem Ausschalten wird das Gerät dann nach der
voreingestellten Zeit automatisch vollständig
abgeschaltet, so dass der Autobatterie kein Strom
mehr entzogen wird.
Wenn Sie die Abschaltautomatik nicht aktivieren,
müssen Sie jedes Mal, wenn Sie die Zündung
ausschalten, die Taste OFF gedrückt halten, bis die
Anzeige ausgeblendet wird.
Näheres dazu finden Sie in der mitgelieferten
Bedienungsanleitung.
Nach dem Ausschalten wird das Gerät dann nach der
voreingestellten Zeit automatisch vollständig
abgeschaltet, so dass der Autobatterie kein Strom
mehr entzogen wird.
Wenn Sie die Abschaltautomatik nicht aktivieren,
müssen Sie jedes Mal, wenn Sie die Zündung
ausschalten, die Taste OFF gedrückt halten, bis die
Anzeige ausgeblendet wird.
Austauschen der Sicherung (
)
Wenn Sie eine Sicherung austauschen, achten Sie
darauf, eine Ersatzsicherung mit dem gleichen
Ampere-Wert wie die Originalsicherung zu
verwenden. Dieser ist auf der Originalsicherung
angegeben. Wenn die Sicherung durchbrennt,
überprüfen Sie den Stromanschluss und tauschen die
Sicherung aus. Brennt die neue Sicherung ebenfalls
durch, kann eine interne Fehlfunktion vorliegen.
Wenden Sie sich in einem solchen Fall an Ihren
Sony-Händler.
darauf, eine Ersatzsicherung mit dem gleichen
Ampere-Wert wie die Originalsicherung zu
verwenden. Dieser ist auf der Originalsicherung
angegeben. Wenn die Sicherung durchbrennt,
überprüfen Sie den Stromanschluss und tauschen die
Sicherung aus. Brennt die neue Sicherung ebenfalls
durch, kann eine interne Fehlfunktion vorliegen.
Wenden Sie sich in einem solchen Fall an Ihren
Sony-Händler.
Stromanschlussdiagramm (
)
Der Hilfsstromanschluss kann je nach Fahrzeugtyp
unterschiedlich sein. Sehen Sie im Hilfsstroman-
schlussdiagramm für Ihr Fahrzeug nach, wie die
Verbindung ordnungsgemäß vorgenommen werden
muss. Es gibt drei grundlegende Typen (ǻ-1, ǻ-2,
unterschiedlich sein. Sehen Sie im Hilfsstroman-
schlussdiagramm für Ihr Fahrzeug nach, wie die
Verbindung ordnungsgemäß vorgenommen werden
muss. Es gibt drei grundlegende Typen (ǻ-1, ǻ-2,
ǻ-3). Sie müssen möglicherweise die rote und gelbe
Leitung des Stromversorgungskabels der
Autostereoanlage vertauschen.
Stellen Sie die Anschlüsse her, schließen Sie die
geschalteten Stromversorgungsleitungen richtig an
und verbinden Sie dann das Gerät mit der
Stromversorgung Ihres Fahrzeugs. Wenn beim
Anschließen des Geräts Fragen oder Probleme
auftreten, die in dieser Anleitung nicht erläutert
werden, wenden Sie sich bitte an den Autohändler.
Leitung des Stromversorgungskabels der
Autostereoanlage vertauschen.
Stellen Sie die Anschlüsse her, schließen Sie die
geschalteten Stromversorgungsleitungen richtig an
und verbinden Sie dann das Gerät mit der
Stromversorgung Ihres Fahrzeugs. Wenn beim
Anschließen des Geräts Fragen oder Probleme
auftreten, die in dieser Anleitung nicht erläutert
werden, wenden Sie sich bitte an den Autohändler.
English
Precautions
ˎ Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
ˎ Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a safe
and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket (
and the bracket (
)
Before installing the unit, remove the protection
collar ʖ and the bracket ʓ from the unit.
collar ʖ and the bracket ʓ from the unit.
1
Remove the protection collar ʖ.
Pinch both edges of the protection collar ʖ, then
pull it out.
Pinch both edges of the protection collar ʖ, then
pull it out.
2
Remove the bracket ʓ.
ɞ Insert both release keys ʕ together between
the unit and the bracket ʓ until they click.
ɟ Pull down the bracket ʓ, then pull up the unit
to separate.
Mounting example (
)
Installation in the dashboard
Notes
ˎ Before installing, make sure that the catches on both sides of the
bracket ʓ are bent inwards 2 mm (
3
/
32
in). If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out (Ǹ-1).
spring out (Ǹ-1).
ˎ Bend these claws outward for a tight fit, if necessary (Ǹ-2).
ˎ Make sure that the 4 catches on the protection collar ʖ are
properly engaged in the slots of the unit (Ǹ-3).
How to detach and attach the
front panel (
front panel (
)
Before installing the unit, detach the front panel.
ǹ-A To detach
Before detaching the front panel, be sure to press and
hold OFF. Press the front panel release button, and
pull it off towards you.
hold OFF. Press the front panel release button, and
pull it off towards you.
ǹ-B To attach
Engage part ʭ of the front panel with part ʮ of the
unit, as illustrated, and push the left side into position
until it clicks.
unit, as illustrated, and push the left side into position
until it clicks.
Warning if your car’s ignition has
no ACC position
no ACC position
Be sure to set the Auto Off function. For details, see
the supplied Operating Instructions.
The unit will shut off completely and automatically in
the set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
OFF until the display disappears each time you turn
the ignition off.
the supplied Operating Instructions.
The unit will shut off completely and automatically in
the set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
OFF until the display disappears each time you turn
the ignition off.
Fuse replacement (
)
When replacing the fuse, be sure to use one matching
the amperage rating stated on the original fuse. If the
fuse blows, check the power connection and replace
the fuse. If the fuse blows again after replacement,
there may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
the amperage rating stated on the original fuse. If the
fuse blows, check the power connection and replace
the fuse. If the fuse blows again after replacement,
there may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Power connection diagram (
)
Auxiliary power connector may vary depending on the
car. Check your car’s auxiliary power connector
diagram to make sure the connections match
correctly. There are three basic types (ǻ-1, ǻ-2, ǻ-3).
You may need to switch the positions of the red and
yellow leads in the car stereo’s power supply lead.
After matching the connections and switched power
supply leads correctly, connect the unit to the car’s
power supply. If you have any questions and problems
connecting your unit that are not covered in this
manual, please consult the car dealer.
car. Check your car’s auxiliary power connector
diagram to make sure the connections match
correctly. There are three basic types (ǻ-1, ǻ-2, ǻ-3).
You may need to switch the positions of the red and
yellow leads in the car stereo’s power supply lead.
After matching the connections and switched power
supply leads correctly, connect the unit to the car’s
power supply. If you have any questions and problems
connecting your unit that are not covered in this
manual, please consult the car dealer.
Deutsch
Sicherheitshinweise
ˎ Wählen Sie den Einbauort sorgfältig so aus, dass das
Gerät beim Fahren nicht hinderlich ist.
ˎ Bauen Sie das Gerät so ein, dass es keinen hohen
Temperaturen (keinem direkten Sonnenlicht, keiner
Warmluft von der Heizung), keinem Staub, keinem
Schmutz und keinen starken Vibrationen ausgesetzt
ist.
Warmluft von der Heizung), keinem Staub, keinem
Schmutz und keinen starken Vibrationen ausgesetzt
ist.
ˎ Für eine sichere Befestigung verwenden Sie stets die
mitgelieferten Montageteile.
Hinweis zum Montagewinkel
Das Gerät sollte in einem Winkel von weniger als 45°
montiert werden.
montiert werden.
Abnehmen der Schutzumrandung
und der Halterung (
und der Halterung (
)
Nehmen Sie vor dem Installieren des Geräts die
Schutzumrandung ʖ und die Halterung ʓ vom
Gerät ab.
Schutzumrandung ʖ und die Halterung ʓ vom
Gerät ab.
1
Entfernen Sie die Schutzumrandung ʖ.
Fassen Sie die Schutzumrandung ʖ mit den
Fingern an den Seitenkanten und ziehen Sie sie
heraus.
Fassen Sie die Schutzumrandung ʖ mit den
Fingern an den Seitenkanten und ziehen Sie sie
heraus.
2
Entfernen Sie die Halterung ʓ.
ɞ Führen Sie beide Löseschlüssel ʕ zwischen
dem Gerät und der Halterung ʓ ein, bis sie mit
einem Klicken einrasten.
einem Klicken einrasten.
ɟ Ziehen Sie die Halterung ʓ nach unten und das
Gerät nach oben, um die beiden zu trennen.
Montagebeispiel (
)
Installation im Armaturenbrett
Hinweise
ˎ Vergewissern Sie sich vor dem Installieren, dass die Verriegelungen
an beiden Seiten der Halterung ʓ um 2 mm nach innen gebogen
sind. Wenn die Verriegelungen gerade oder nach außen gebogen
sind, lässt sich das Gerät nicht sicher installieren und kann
herausspringen (Ǹ-1).
sind. Wenn die Verriegelungen gerade oder nach außen gebogen
sind, lässt sich das Gerät nicht sicher installieren und kann
herausspringen (Ǹ-1).
ˎ Falls erforderlich, biegen Sie diese Klammern für einen sicheren
Halt nach außen (Ǹ-2).
ˎ Achten Sie darauf, die 4 Verriegelungen an der Schutzumrandung
ʖ korrekt in die Aussparungen am Gerät einzusetzen (Ǹ-3).
Français
Précautions
ˎ Choisir soigneusement l’emplacement de
l’installation afin que l’appareil ne gêne pas la
conduite normale du véhicule.
conduite normale du véhicule.
ˎ Eviter d’installer l’appareil dans un endroit exposé à
de la poussière, de la saleté, des vibrations violentes
ou à des températures élevées, comme en plein
soleil ou à proximité d’un conduit de chauffage.
ou à des températures élevées, comme en plein
soleil ou à proximité d’un conduit de chauffage.
ˎ Pour garantir un montage sûr, n’utiliser que le
matériel fourni.
Réglage de l’angle de montage
Ajuster l’inclinaison à un angle inférieur à 45°.
Retrait du tour de protection et
du support (
du support (
)
Avant d’installer l’appareil, retirez le tour de
protection ʖ et le support ʓ de l’appareil.
protection ʖ et le support ʓ de l’appareil.
1
Retirez le tour de protection ʖ.
Saisissez les deux bords du tour de protection ʖ,
puis tirez pour l'extraire.
Saisissez les deux bords du tour de protection ʖ,
puis tirez pour l'extraire.
2
Retirez le support ʓ.
ɞ Insérez les deux clés de déblocage ʕ
simultanément entre l’appareil et le support ʓ
jusqu’au déclic indiquant qu’elles sont en place.
jusqu’au déclic indiquant qu’elles sont en place.
ɟ Tirez le support ʓ vers le bas, puis tirez
l’appareil vers le haut pour les séparer.
Exemple de montage (
)
Installation dans le tableau de bord
Remarques
ˎ Avant l’installation, assurez-vous que les loquets des deux côtés du
support ʓ sont bien pliés de 2 mm vers l’intérieur. Si les loquets
sont droits ou pliés vers l’extérieur, l’appareil ne peut pas être fixé
solidement et peut se détacher (Ǹ-1).
sont droits ou pliés vers l’extérieur, l’appareil ne peut pas être fixé
solidement et peut se détacher (Ǹ-1).
ˎ Pliez ces griffes vers l’extérieur pour assurer une prise correcte si
nécessaire (Ǹ-2).
ˎ Assurez-vous que les 4 loquets du tour de protection ʖ sont
correctement insérés dans les fentes de l’appareil (Ǹ-3).
Retrait et fixation de la façade
(
(
)
Avant d’installer l’appareil, retirez la façade.
ǹ-A Pour la retirer
Avant de retirer la façade, veillez à appuyer sur la
touche OFF et à la maintenir enfoncée. Appuyez sur la
touche de déverrouillage de la façade et détachez-la
en la tirant vers vous.
touche OFF et à la maintenir enfoncée. Appuyez sur la
touche de déverrouillage de la façade et détachez-la
en la tirant vers vous.
ǹ-B Pour la fixer
Fixez la partie ʭ de la façade sur la partie ʮ de
l’appareil, comme indiqué sur l’illustration, puis
appuyez sur le côté gauche jusqu’au déclic.
l’appareil, comme indiqué sur l’illustration, puis
appuyez sur le côté gauche jusqu’au déclic.
Avertissement au cas où le
contact de votre voiture ne
dispose pas d’une position ACC
contact de votre voiture ne
dispose pas d’une position ACC
Veillez à régler la fonction de mise hors tension
automatique. Pour obtenir davantage d’informations,
reportez-vous au mode d’emploi fourni.
L’appareil s’éteint complètement et automatiquement
après le laps de temps choisi une fois qu’il a été mis
hors tension afin d’éviter que la batterie ne se
décharge.
Si vous ne réglez pas la fonction de mise hors tension
automatique, appuyez sur la touche OFF et
maintenez-la enfoncée jusqu’à ce que l’affichage
disparaisse à chaque fois que vous coupez le contact.
automatique. Pour obtenir davantage d’informations,
reportez-vous au mode d’emploi fourni.
L’appareil s’éteint complètement et automatiquement
après le laps de temps choisi une fois qu’il a été mis
hors tension afin d’éviter que la batterie ne se
décharge.
Si vous ne réglez pas la fonction de mise hors tension
automatique, appuyez sur la touche OFF et
maintenez-la enfoncée jusqu’à ce que l’affichage
disparaisse à chaque fois que vous coupez le contact.
Remplacement du fusible (
)
Lorsque vous remplacez le fusible, veillez à utiliser un
fusible dont l’intensité, en ampères, correspond à la
valeur indiquée sur le fusible usagé. Si le fusible saute,
vérifiez le branchement de l’alimentation et
remplacez-le. Si le nouveau fusible saute également, il
est possible que l’appareil soit défectueux. Dans ce
cas, consultez votre revendeur Sony le plus proche.
fusible dont l’intensité, en ampères, correspond à la
valeur indiquée sur le fusible usagé. Si le fusible saute,
vérifiez le branchement de l’alimentation et
remplacez-le. Si le nouveau fusible saute également, il
est possible que l’appareil soit défectueux. Dans ce
cas, consultez votre revendeur Sony le plus proche.
Schéma de raccordement
d’alimentation (
d’alimentation (
)
Le connecteur d’alimentation auxiliaire peut varier
suivant le type de voiture. Vérifiez le schéma du
connecteur d’alimentation auxiliaire de votre voiture
pour vous assurer que les connexions correspondent.
Il en existe trois types de base (ǻ-1, ǻ-2, ǻ-3). Il se
peut que vous deviez commuter la position des fils
rouge et jaune du câble d’alimentation de l’autoradio.
Après avoir établi les connexions et commuté
correctement les câbles d’alimentation, raccordez
l’appareil à l’alimentation de la voiture. Si vous avez
des questions ou des difficultés à propos de cet
appareil qui ne sont pas abordées dans le présent
mode d’emploi, consultez votre concessionnaire
automobile.
suivant le type de voiture. Vérifiez le schéma du
connecteur d’alimentation auxiliaire de votre voiture
pour vous assurer que les connexions correspondent.
Il en existe trois types de base (ǻ-1, ǻ-2, ǻ-3). Il se
peut que vous deviez commuter la position des fils
rouge et jaune du câble d’alimentation de l’autoradio.
Après avoir établi les connexions et commuté
correctement les câbles d’alimentation, raccordez
l’appareil à l’alimentation de la voiture. Si vous avez
des questions ou des difficultés à propos de cet
appareil qui ne sont pas abordées dans le présent
mode d’emploi, consultez votre concessionnaire
automobile.
Italiano
Precauzioni
ˎ Scegliere con attenzione la posizione per
l’installazione in modo che l’apparecchio non
interferisca con le operazioni di guida del
conducente.
interferisca con le operazioni di guida del
conducente.
ˎ Evitare di installare l’apparecchio dove sia soggetto
ad alte temperature, come alla luce solare diretta o
al getto di aria calda dell’impianto di riscaldamento,
o dove possa essere soggetto a polvere, sporco e
vibrazioni eccessive.
al getto di aria calda dell’impianto di riscaldamento,
o dove possa essere soggetto a polvere, sporco e
vibrazioni eccessive.
ˎ Usare solo il materiale di montaggio in dotazione
per un’installazione stabile e sicura.
Regolazione dell’angolo di montaggio
Regolare l’angolo di montaggio in modo che sia
inferiore a 45°.
inferiore a 45°.
Rimozione della staffa e della
cornice protettiva (
cornice protettiva (
)
Prima di installare l’apparecchio, rimuovere la
cornice protettiva ʖ e la staffa ʓ dall’apparecchio.
cornice protettiva ʖ e la staffa ʓ dall’apparecchio.
1
Rimuovere la cornice protettiva ʖ.
Afferrare la cornice di protezione ʖ dai bordi
laterali, quindi estrarla.
Afferrare la cornice di protezione ʖ dai bordi
laterali, quindi estrarla.
2
Rimuovere la staffa ʓ.
ɞ Inserire contemporaneamente entrambe le
chiavette di rilascio ʕ tra l’apparecchio e la
staffa ʓ fino a che non scattano in posizione.
staffa ʓ fino a che non scattano in posizione.
ɟ Estrarre la staffa ʓ, quindi sollevare
l’apparecchio per rimuoverlo.
Esempio di montaggio (
)
Installazione nel cruscotto
Note
ˎ Prima di installare l’unità, accertarsi di ripiegare i fermi presenti su
entrambi i lati della staffa ʓ verso l’interno di 2 mm. Se i fermi sono
diritti o ripiegati verso l’esterno, l’apparecchio non verrà installato in
modo sicuro e potrebbe fuoriuscire (Ǹ-1).
diritti o ripiegati verso l’esterno, l’apparecchio non verrà installato in
modo sicuro e potrebbe fuoriuscire (Ǹ-1).
ˎ Piegare verso l’esterno questi morsetti per un’installazione più
sicura, se necessario (Ǹ-2).
ˎ Assicurarsi che i 4 fermi sulla cornice protettiva ʖ siano
correttamente inseriti negli alloggiamenti dell’apparecchio (Ǹ-3).
Come rimuovere e reinserire il
pannello anteriore (
pannello anteriore (
)
Prima di installare l’apparecchio rimuovere il
pannello anteriore.
pannello anteriore.
ǹ-A Per rimuoverlo
Prima di rimuovere il pannello anteriore, assicurarsi di
tenere premuto OFF. Premere il tasto rilascio pannello
anteriore, quindi tirare il pannello verso di sé.
tenere premuto OFF. Premere il tasto rilascio pannello
anteriore, quindi tirare il pannello verso di sé.
ǹ-B Per reinserirlo
Applicare la parte ʭ del pannello anteriore alla parte
ʮ dell’apparecchio come mostrato nell’illustrazione e
premere il lato sinistro fino a sentire uno scatto.
premere il lato sinistro fino a sentire uno scatto.
Avvertenza relativa
all’installazione su un’auto
sprovvista della posizione ACC
(accessoria) sul blocchetto di
accensione
all’installazione su un’auto
sprovvista della posizione ACC
(accessoria) sul blocchetto di
accensione
Accertarsi di impostare la funzione di spegnimento
automatico. Per ulteriori informazioni, fare riferimento
alle istruzioni per l’uso in dotazione.
L’apparecchio si spegne completamente e
automaticamente all’ora impostata dopo che è stato
disattivato, onde evitare che la batteria si scarichi.
Se la funzione di spegnimento automatico non è stata
impostata, ogni volta che il motore viene spento
tenere premuto OFF finché il display non viene
disattivato.
automatico. Per ulteriori informazioni, fare riferimento
alle istruzioni per l’uso in dotazione.
L’apparecchio si spegne completamente e
automaticamente all’ora impostata dopo che è stato
disattivato, onde evitare che la batteria si scarichi.
Se la funzione di spegnimento automatico non è stata
impostata, ogni volta che il motore viene spento
tenere premuto OFF finché il display non viene
disattivato.
Sostituzione del fusibile (
)
Per la sostituzione del fusibile, assicurarsi di utilizzare
un fusibile dello stesso amperaggio di quello indicato
sull’originale. Se il fusibile si brucia, controllare i
collegamenti dell’alimentazione e sostituire il fusibile.
Se dopo la sostituzione il fusibile si brucia di nuovo, è
possibile che si tratti di un problema interno. In tal
caso, rivolgersi al più vicino rivenditore Sony.
un fusibile dello stesso amperaggio di quello indicato
sull’originale. Se il fusibile si brucia, controllare i
collegamenti dell’alimentazione e sostituire il fusibile.
Se dopo la sostituzione il fusibile si brucia di nuovo, è
possibile che si tratti di un problema interno. In tal
caso, rivolgersi al più vicino rivenditore Sony.
Diagramma dei collegamenti di
alimentazione (
alimentazione (
)
Il connettore di alimentazione ausiliaria può variare a
seconda della macchina. Controllare il diagramma del
connettore di alimentazione ausiliaria della macchina
per essere sicuri che i collegamenti corrispondano
correttamente. Vi sono tre tipi di base (ǻ-1, ǻ-2,
seconda della macchina. Controllare il diagramma del
connettore di alimentazione ausiliaria della macchina
per essere sicuri che i collegamenti corrispondano
correttamente. Vi sono tre tipi di base (ǻ-1, ǻ-2,
ǻ-3). Potrebbe essere necessario cambiare le
posizioni dei fili rosso e giallo nel cavo di
alimentazione dello stereo della macchina.
Dopo aver fatto corrispondere i collegamenti e aver
commutato i cavi di alimentazione, collegare
l’apparecchio all’alimentazione della macchina. Se si
hanno domande o se sorgono problemi che non sono
stati trattati nel manuale nel collegare l’apparecchio,
contattare l’autoconcessionario.
posizioni dei fili rosso e giallo nel cavo di
alimentazione dello stereo della macchina.
Dopo aver fatto corrispondere i collegamenti e aver
commutato i cavi di alimentazione, collegare
l’apparecchio all’alimentazione della macchina. Se si
hanno domande o se sorgono problemi che non sono
stati trattati nel manuale nel collegare l’apparecchio,
contattare l’autoconcessionario.
Nederlands
Voorzorgsmaatregelen
ˎ Kies de installatieplaats zorgvuldig zodat het
apparaat de bestuurder niet hindert tijdens het
rijden.
rijden.
ˎ Installeer het apparaat niet op plaatsen waar het
blootgesteld wordt aan hoge temperaturen, bv. in
direct zonlicht of bij de warme luchtstroom van de
autoverwarming, aan sterke trillingen, of waar het in
contact komt met veel stof of vuil.
direct zonlicht of bij de warme luchtstroom van de
autoverwarming, aan sterke trillingen, of waar het in
contact komt met veel stof of vuil.
ˎ Gebruik voor het veilig en stevig monteren van het
apparaat uitsluitend de bijgeleverde montage-
onderdelen.
onderdelen.
Maximale montagehoek
Installeer het apparaat nooit in een hoek van meer
dan 45° met het horizontale vlak.
dan 45° met het horizontale vlak.
De beschermende rand en de
beugel verwijderen (
beugel verwijderen (
)
Voordat u het apparaat gaat installeren, moet u de
beschermende rand ʖ en de beugel ʓ verwijderen
van het apparaat.
beschermende rand ʖ en de beugel ʓ verwijderen
van het apparaat.
1
Verwijder de beschermende rand ʖ.
Druk beide zijden van de beschermende rand ʖ in
en trek de rand naar u toe.
Druk beide zijden van de beschermende rand ʖ in
en trek de rand naar u toe.
2
Verwijder de beugel ʓ.
ɞ Plaats de ontgrendelingssleutels ʕ tussen het
apparaat en de beugel ʓ tot deze vastklikken.
ɟ Trek de beugel ʓ omlaag en trek het apparaat
omhoog om deze van elkaar te scheiden.
Montagevoorbeeld (
)
Montage in het dashboard
Opmerkingen
ˎ Voordat u het apparaat installeert, moet u de grepen aan beide
zijden van de beugel ʓ 2 mm naar binnen buigen. Als de grepen
recht zijn of naar buiten gebogen, kan het apparaat niet goed
worden bevestigd en kan dit losschieten (Ǹ-1).
recht zijn of naar buiten gebogen, kan het apparaat niet goed
worden bevestigd en kan dit losschieten (Ǹ-1).
ˎ Indien nodig kunt u deze klemhaken ombuigen voor een stevigere
bevestiging (Ǹ-2).
ˎ De 4 grepen op de beschermende rand ʖ moeten goed in de
sleuven van het apparaat zijn geplaatst (Ǹ-3).
Het voorpaneel verwijderen en
bevestigen (
bevestigen (
)
Verwijder, alvorens met het installeren te beginnen,
het afneembare voorpaneel.
het afneembare voorpaneel.
ǹ-A Verwijderen
Voordat u het voorpaneel verwijdert, moet u OFF
ingedrukt houden. Druk op de toets om het
voorpaneel los te maken en trek het voorpaneel naar
u toe.
ingedrukt houden. Druk op de toets om het
voorpaneel los te maken en trek het voorpaneel naar
u toe.
ǹ-B Bevestigen
Breng deel ʭ van het voorpaneel aan op deel ʮ van
het apparaat zoals afgebeeld en druk op de linkerzijde
tot deze vastklikt.
het apparaat zoals afgebeeld en druk op de linkerzijde
tot deze vastklikt.
Waarschuwing als het contactslot
van de auto geen ACC-positie
heeft
van de auto geen ACC-positie
heeft
Zorg ervoor dat u de functie voor automatisch
uitschakelen instelt. Raadpleeg de bijgeleverde
gebruiksaanwijzing voor meer informatie.
Het apparaat wordt na de ingestelde tijd automatisch
volledig uitgeschakeld nadat het apparaat is
uitgeschakeld. Zo wordt voorkomen dat de accu
leegloopt.
Als u de functie voor automatisch uitschakelen niet
instelt, moet u OFF ingedrukt houden tot het display
verdwijnt telkens wanneer u het contact uitschakelt.
uitschakelen instelt. Raadpleeg de bijgeleverde
gebruiksaanwijzing voor meer informatie.
Het apparaat wordt na de ingestelde tijd automatisch
volledig uitgeschakeld nadat het apparaat is
uitgeschakeld. Zo wordt voorkomen dat de accu
leegloopt.
Als u de functie voor automatisch uitschakelen niet
instelt, moet u OFF ingedrukt houden tot het display
verdwijnt telkens wanneer u het contact uitschakelt.
Zekering vervangen (
)
Vervang een zekering altijd door een exemplaar van
eenzelfde ampèrage als op de oorspronkelijke
zekering wordt vermeld. Als de zekering doorbrandt,
moet u de voedingsaansluiting controleren en de
zekering vervangen. Brandt de zekering vervolgens
nogmaals door, dan kan er sprake zijn van een defect
in het apparaat. Raadpleeg in dat geval de Sony-
dealer bij u in de buurt.
eenzelfde ampèrage als op de oorspronkelijke
zekering wordt vermeld. Als de zekering doorbrandt,
moet u de voedingsaansluiting controleren en de
zekering vervangen. Brandt de zekering vervolgens
nogmaals door, dan kan er sprake zijn van een defect
in het apparaat. Raadpleeg in dat geval de Sony-
dealer bij u in de buurt.
Voedingsaansluitschema (
)
De hulpvoedingsaansluiting kan verschillen
afhankelijk van de auto. Controleer het
hulpvoedingsaansluitschema dat bij dit apparaat
wordt geleverd om te zien of de aansluitingen
kloppen. Er zijn drie basistypes (ǻ-1, ǻ-2, ǻ-3). Het
is mogelijk dat u de posities van de rode en gele
kabels in de voedingskabel van het autoaudiosysteem
moet omwisselen.
Als de aansluitingen en geschakelde voedingskabels
kloppen, sluit u het apparaat aan op de voeding van
de auto. Indien u nog vragen of problemen hebt in
verband met het aansluiten van het apparaat die niet
in deze handleiding worden behandeld, raadpleeg
dan de autodealer.
afhankelijk van de auto. Controleer het
hulpvoedingsaansluitschema dat bij dit apparaat
wordt geleverd om te zien of de aansluitingen
kloppen. Er zijn drie basistypes (ǻ-1, ǻ-2, ǻ-3). Het
is mogelijk dat u de posities van de rode en gele
kabels in de voedingskabel van het autoaudiosysteem
moet omwisselen.
Als de aansluitingen en geschakelde voedingskabels
kloppen, sluit u het apparaat aan op de voeding van
de auto. Indien u nog vragen of problemen hebt in
verband met het aansluiten van het apparaat die niet
in deze handleiding worden behandeld, raadpleeg
dan de autodealer.
ʓ
ʕ
Face the hook inwards.
Der Haken muss nach innen weisen.
Tournez le crochet vers l’intérieur.
Con il gancetto rivolto verso l’interno.
Het haakje moet naar binnen wijzen.
Der Haken muss nach innen weisen.
Tournez le crochet vers l’intérieur.
Con il gancetto rivolto verso l’interno.
Het haakje moet naar binnen wijzen.
q
q
q
Auxiliary power connector
Hilfsstromanschluss
Connecteur d’alimentation auxiliaire
Connettore di alimentazione ausiliaria
Hulpvoedingsaansluiting
Hilfsstromanschluss
Connecteur d’alimentation auxiliaire
Connettore di alimentazione ausiliaria
Hulpvoedingsaansluiting
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
the car without ACC position
Fahrzeug ohne Zubehörposition (ACC oder I)
Véhicule sans position ACC
Auto priva della posizione ACC
Auto zonder ACC-positie
4
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
7
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
4
Yellow
Gelb
Jaune
Giallo
Geel
Gelb
Jaune
Giallo
Geel
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
7
Red
Rot
Rouge
Rosso
Rood
Rot
Rouge
Rosso
Rood
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
permanente Stromversorgung
alimentation continue
alimentazione continua
continue voeding
Claws
Klammern
Griffes
Morsetti
Klemhaken
Klammern
Griffes
Morsetti
Klemhaken
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
OFF
Front panel release button
Taste zum Lösen der
Frontplatte
Touche de déverrouillage
de la façade
Tasto rilascio pannello
anteriore
Toets om het voorpaneel
los te maken
Taste zum Lösen der
Frontplatte
Touche de déverrouillage
de la façade
Tasto rilascio pannello
anteriore
Toets om het voorpaneel
los te maken
Catch
Verriegelung
Loquet
Fermo
Greep
Verriegelung
Loquet
Fermo
Greep
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
ʓ
1
2
q
ʖ
1
A
B
3
2
1
3
2
Dashboard
Armaturenbrett
Tableau de bord
Cruscotto
Dashboard
Armaturenbrett
Tableau de bord
Cruscotto
Dashboard
Fire wall
Motorraumtrennwand
Paroi ignifuge
Parete tagliafiamma
Brandschot
Motorraumtrennwand
Paroi ignifuge
Parete tagliafiamma
Brandschot
ʖ
ʗ
ʘ
ʓ
Click on the first or last page to see other CDX-G1000U / CDX-G1000UE / CDX-G1001U / CDX-G1002U / CDX-G1050U / CDX-G1050UE / CDX-G1051U / CDX-G1070U / CDX-G1071U / CDX-G1080UM service manuals if exist.