Sony CDX-F5500 / CDX-F5500X / CXS-F550GF Service Manual ▷ View online
5
CDX-F5500/F5500X
4
Location of controls
Refer to the pages listed for details.
a
DSO button 23
b
SOURCE (Power on/Radio/CD/MD)
button
button
To select the source.
c
LIST
button 14, 15, 18
d
Receptor for the card remote
commander
commander
e
Display window
f Z
(eject) button
(located on the front side
of the unit, behind the front panel)
11
g
OPEN button 10, 11
h
EQ3 button 22
i
MODE button
To change operation.
j
Volume control dial/Select button
Rotate to:
– Adjust the volume.
– Adjust settings.
Press to:
– Select items.
– Adjust the volume.
– Adjust settings.
Press to:
– Select items.
k
DSPL (display mode change) button
11, 12, 14, 21
11, 12, 14, 21
l
SENS button 16
m
RESET button
(located on the front side of
the unit, behind the front panel)
9
n
BTM button
o
Number buttons 21
Radio:
To store stations/receive stored stations.
CD/MD:
(3)
To store stations/receive stored stations.
CD/MD:
(3)
: REP 13
(4)
: SHUF 13
p
Frequency select switch
(located on the
bottom of the unit)
See “Frequency select switch” in the
Installation/Connections manual.
See “Frequency select switch” in the
Installation/Connections manual.
q
OFF (Stop/Power off) button
*
10,
11
*
Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold
(OFF)
on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
causes battery drain.
PU
SH
DIA
L
SE
LE
C
T
SO
UR
CE
DISC/PRESET
OPEN
6
5
4
3
BBE
SHUF
REP
2
1
BTM
SENS
EQ3
DS
PL
M
OD
E
CDX-F5500X
DSO
SEEK
SEEK
LIS
T
OFF
4
Location of controls
Refer to the pages listed for details.
a
DSO button
22
b
SOURCE (Power on/Radio/CD/MD)
button
button
To select the source.
c
LIST/CAT
*
1
button
14, 15, 18
d
Receptor for the card remote
commander
commander
e
Display window
f Z
(eject) button
(located on the front side
of the unit, behind the front panel)
11
g
OPEN button
10, 11
h
EQ3 button
21, 22
i
MODE button
To change operation.
j
Volume control dial/Select button
Rotate to:
– Adjust the volume.
– Adjust settings.
Press to:
– Select items.
– Adjust the volume.
– Adjust settings.
Press to:
– Select items.
k
DSPL (display mode change) button
11, 12, 14, 21
l
SENS button
16
m
RESET button
(located on the front side of
the unit, behind the front panel)
9
n
BTM button
o
Number buttons
21
Radio:
To store stations/receive stored stations.
CD/MD:
(3)
To store stations/receive stored stations.
CD/MD:
(3)
: REP
13
(4)
: SHUF
13
p
OFF (Stop/Power off) button
*
2
10,
11
*1 (CAT)
is available only when the XM tuner is
connected.
*2
Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold
and hold
(OFF)
on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
causes battery drain.
PU
SH
DIA
L
SE
LE
C
T
SO
UR
CE
DISC/PRESET
OPEN
6
5
4
3
BBE
SHUF
REP
2
1
BTM
SENS
EQ3
DS
PL
M
OD
E
CDX-F5500
DSO
SEEK
SEEK
LIS
T
CA
T
OFF
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
(US, Canadian Model)
(E Model)
5
q
DISC (ALBUM)/PRESET buttons (+/–)
To receive preset stations/change the disc*
1
,
skip albums*
2
.
*1
When an optional CD/MD unit is connected.
*2
Available only when an MP3 file is played.
r
SEEK buttons (–/+)
To skip tracks/fast-forward, reverse a track/
tune in stations automatically, find a station
manually/select a setting.
tune in stations automatically, find a station
manually/select a setting.
The corresponding buttons of the card
remote commander control the same
functions as those on this unit.
remote commander control the same
functions as those on this unit.
a
DSPL button
b
SOURCE button
c
SEEK (–/+) buttons
d
OFF button
e
VOL (+/–) buttons
f
MODE button
g
PRESET (DISC/ALBUM) (+/–) buttons
h
ATT button
Note
If the display disappears by pressing
If the display disappears by pressing
(OFF)
, it cannot
be operated with the card remote commander unless
(SOURCE)
on the unit is pressed, or a disc is inserted
to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery” on page 23.
For details on how to replace the battery, see
“Replacing the lithium battery” on page 23.
SEEK
SEEK
PU
SH
DIA
L
SE
LE
C
T
SO
UR
CE
DISC/PRESET
SENS
EQ3
DS
PL
M
OD
E
DSO
SEEK
SEEK
LIS
T
CA
T
(SEEK)
(–): to select
leftwards/
.
(SEEK)
(+): to select
rightwards/
>
(DISC/PRESET)
(+): to select upwards
(DISC/PRESET)
(–): to select downwards
Card remote commander RM-X115
continue to next page
t
ATT
OFF
DSPL
MODE
SOURCE
VOL
+
–
PRESET
+
PRESET
–
SEEK–
SEEK+
6
CDX-F5500/F5500X
Connections (US, Canadian Model)
L
R
BUS AUDIO IN
AUDIO OUT
FRONT
AUDIO OUT
REAR
*
2
BUS
CONTROL IN
REMOTE
IN
Schéma de raccordement (
3
)
1
À un point métallique de la voiture
Branchez d‘abord le fil de masse noir et, ensuite,
les fils d‘entrée d‘alimentation jaune et rouge.
les fils d‘entrée d‘alimentation jaune et rouge.
2
Vers le fil de commande de l‘antenne électrique
ou le fil d‘alimentation de l‘amplificateur
d‘antenne
ou le fil d‘alimentation de l‘amplificateur
d‘antenne
Remarques
• Il n'est pas nécessaire de raccorder ce fil s'il n'y a
• Il n'est pas nécessaire de raccorder ce fil s'il n'y a
pas d'antenne électrique ni d'amplificateur
d'antenne, ou avec une antenne télescopique
manuelle.
d'antenne, ou avec une antenne télescopique
manuelle.
• Si votre voiture est équipée d'une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
« Remarques sur les fils de commande et
d'alimentation ».
« Remarques sur les fils de commande et
d'alimentation ».
3
Au niveau du AMP REMOTE IN de l’amplificateur
de puissance en option
de puissance en option
Ce raccordement s’applique uniquement aux
amplificateurs. Le
amplificateurs. Le
branchement de tout autre
système risque d’endommager l’appareil.
4
Vers le cordon de liaison d’un téléphone de
voiture
voiture
5
À la borne +12 V qui est alimentée quand la clé
de contact est sur la position accessoires
de contact est sur la position accessoires
Remarques
• S'il n'y a pas de position accessoires, raccordez la
• S'il n'y a pas de position accessoires, raccordez la
borne d'alimentation (batterie) +12 V qui est
alimentée en permanence.
Raccordez d’abord le fil de masse noir à un
point métallique du véhicule.
alimentée en permanence.
Raccordez d’abord le fil de masse noir à un
point métallique du véhicule.
• Si votre voiture est équipée d'une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
« Remarques sur les fils de commande et
d'alimentation ».
« Remarques sur les fils de commande et
d'alimentation ».
6
À la borne +12 V qui est alimentée en
permanence
permanence
Raccordez d’abord le fil de masse noir à un point
métallique du véhicule.
métallique du véhicule.
Remarques sur les fils de commande et
d
d
’alimentation
• Le fil de commande de l’antenne électrique (bleu)
fournit une alimentation de +12
V
CC
lorsque vous
mettez la radio sous tension.
• Lorsque votre voiture est équipée d’une antenne
FM/AM intégrée dans la vitre arrière/latérale,
raccordez le fil de commande de l’antenne (bleu)
ou l’entrée d’alimentation des accessoires (rouge) à
la borne d’alimentation de l’amplificateur
d’antenne existant. Pour plus de détails, consultez
votre détaillant.
raccordez le fil de commande de l’antenne (bleu)
ou l’entrée d’alimentation des accessoires (rouge) à
la borne d’alimentation de l’amplificateur
d’antenne existant. Pour plus de détails, consultez
votre détaillant.
• Une antenne électrique sans boîtier de relais ne
peut pas être utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le fil d’entrée d’alimentation jaune est
raccordé, le circuit de la mémoire est alimenté en
permanence même si la clé de contact est sur la
position d’arrêt.
Lorsque le fil d’entrée d’alimentation jaune est
raccordé, le circuit de la mémoire est alimenté en
permanence même si la clé de contact est sur la
position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez
• Avant de raccorder les haut-parleurs, mettez
l’appareil hors tension.
• Utilisez des haut-parleurs ayant une impédance de
4 à 8 ohms avec une capacité électrique adéquate
pour éviter de les endommager.
pour éviter de les endommager.
• Ne raccordez pas les bornes du système de haut-
parleurs au châssis de la voiture et ne raccordez pas
les bornes des haut-parleurs droit à celles du haut-
parleur gauche.
les bornes des haut-parleurs droit à celles du haut-
parleur gauche.
• Ne raccordez pas le câble de masse de cet appareil à
la borne négative (–) de l’enceinte.
• N’essayez pas de raccorder les haut-parleurs en
parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec
amplificateurs intégrés) aux bornes des
amplificateurs intégrés) aux bornes des
haut-
parleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas
les fils des haut-parleurs intégrés installés dans
votre voiture si l’appareil partage un fil négatif
commun (–) pour les haut-parleurs droit et gauche.
votre voiture si l’appareil partage un fil négatif
commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-
parleurs de l’appareil.
Remarque sur le raccordement
Si les haut-parleurs et l’amplificateur ne sont pas
raccordés correctement, le message « FAILURE »
s’affiche. Dans ce cas, assurez-vous que les haut-
parleurs et l’amplificateur sont bien raccordés.
Si les haut-parleurs et l’amplificateur ne sont pas
raccordés correctement, le message « FAILURE »
s’affiche. Dans ce cas, assurez-vous que les haut-
parleurs et l’amplificateur sont bien raccordés.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies
• The power antenna control lead (blue) supplies
+12 V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
• A power antenna without a relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
3
Supplied with XA-C30
Fourni avec le XA-C30
Fourni avec le XA-C30
Source selector
(not supplied)
Sélecteur de source
(non fourni)
XA-C30
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Courant max. fourni 0,3 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Rayé bleu/blanc
Rayé bleu/blanc
White
Blanc
Blanc
Green
Vert
Vert
Purple
Mauve
Mauve
White/black striped
Rayé blanc/noir
Rayé blanc/noir
Gray/black striped
Rayé gris/noir
Rayé gris/noir
Green/black striped
Rayé vert/noir
Rayé vert/noir
Purple/black striped
Rayé mauve/noir
Rayé mauve/noir
Gray
Gris
Gris
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Fourni avec le changeur de CD/MD
3
*
3
from car antenna
à partir de l’antenne de la voiture
à partir de l’antenne de la voiture
Left
Gauche
Gauche
Right
Droit
Droit
Left
Gauche
Gauche
Right
Droit
Droit
2
5
6
4
ANT REM
4
Red
Rouge
Rouge
Yellow
Jaune
Jaune
Black
Noir
Noir
Blue
Bleu
Bleu
Light blue
Bleu ciel
Bleu ciel
Max. supply current 0.1 A
Courant max. fourni 0,1 A
ATT
1
*
1
*
1
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched to REAR
or SUB.
For details, see the supplied operating
instructions.
or SUB.
For details, see the supplied operating
instructions.
*
3
Insert with the cord upwards.
*
1
Cordon à broche RCA (non fourni)
*
2
AUDIO OUT peut être commuté sur
REAR ou SUB.
Pour obtenir plus de détails, reportez-
vous au mode d'emploi fourni.
REAR ou SUB.
Pour obtenir plus de détails, reportez-
vous au mode d'emploi fourni.
*
3
Insérez avec le câble vers le bas.
CDX-F5500 only
CDX-F5500 uniquement
CDX-F5500 uniquement
Connection diagram (
3
)
1
To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
connect the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
6
To the +12 V power terminal which is energized
at all times
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
metal surface of the car first.
7
CDX-F5500/F5500X
Connections (E Model)
8
CDX-F5500/F5500X
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
2-1.
SUB PANEL ASSY (CD)
(Page 9)
(Page 9)
2-2.
CD MECHANISM BLOCK
(Page 9)
(Page 9)
SET
2-3.
MAIN BOARD
(Page 10)
(Page 10)
2-4.
CHASSIS (T) SUB ASSY
(Page 10)
(Page 10)
2-5.
ROLLER ARM ASSY
(Page 11)
(Page 11)
2-6.
CHASSIS (OP) ASSY
(Page 11)
(Page 11)
2-8.
SL MOTOR ASSY (M902)
(Page 12)
(Page 12)
2-10. SERVO BOARD
(Page 13)
2-7.
OPTICAL PICK-UP
(Page 12)
(Page 12)
2-9.
LE MOTOR ASSY (M903)
(Page 13)
(Page 13)
Click on the first or last page to see other CDX-F5500 / CDX-F5500X / CXS-F550GF service manuals if exist.