Sony ZS-S10CP Service Manual ▷ View online
ZS-S10CP
9
2-5. MAIN BOARD
3 two cabinet upper
cushions 10 X 7 X0.3
5 MAIN board
MAIN board
3 two cabinet upper
cushions 10 X 7 X0.3
2 flexible flat cable (16 core) (FFC801)
(CN810)
flexible flat cable (16 core) (FFC801)
WireVeWWiQJ
Tape
Tape
coloured line
coloured line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the coloured line.
No slanting after insertion.
4 cushion (A)
1 tape
10 mm
10 mm
10 mm
+RZWREeQGIOe[iEOeIODWFDEOeFRre))&
ZS-S10CP
10
2-7. OPTICAL PICK-UP (DA11MMVGP) (OP1)
2-6. CD BLOCK ASSY
2 CD block assy
1 two tapping screws
(PWH
B2.6)
1 two tapping screws
(PWH
B2.6)
– Cabinet (upper) block bottom side view –
3 claw
2 vibration proof rubber
(green)
1 vibration proof rubber
(red)
3 claw
3 claw
3 claw
1 vibration proof rubber
(red)
7 optical pick-up (DA11MMVGP)
(OP1)
optical pick-up
(DA11MMVGP)
(OP1)
(DA11MMVGP)
(OP1)
6 MOTOR board
4 CD cover
Note: Three claws might be fixed by bond.
When installing the CD cover, please
fix three claws using the following bond.
Part No.
Description
7-432-912-48 SONY BOND SC608LV (180 ml)
2 vibration proof rubber
(green)
vibration proof rubber
Upper side
Lower side
5 Remove four solders.
9LEUDWLRQSURRIUXEEHUVHWWLQJ
ZS-S10CP
11
2-8. CD SPRING
1 Open the CD lid.
5 CD spring
CD spring
4 shaft
3 claw
&'VSULQJVHWWLQJ
&'VSULQJVHWWLQJ
CD lid
2 Remove the spring
(CD) from the ditch
of CD lid.
ditch
CD spring
CD lid
OK
NG
1 Insert the CD spring.
4 Insert the CD spring
to the ditch of CD lid.
2 Insert in the shaft.
$VVHPEOLQJSURFHGXUHRIWKH&'VSULQJ
3 Hook CD spring on claw.
ZS-S10CP
12
2-9. SPEAKER (7.7 cm) (SP101, SP201)
4 speaker (7.7 cm)
(R-CH)
(SP201)
4 speaker (7.7 cm) (L-CH) (SP101)
speaker (7.7 cm)
(R-CH) (SP201)
(R-CH) (SP201)
speaker (7.7 cm)
(L-CH) (SP101)
(L-CH) (SP101)
red (
+)
white (
−)
1 four tapping screws
(BV
B2.6)
2 Remove the speaker (7.7 cm) (R-CH)
(SP201) in the direction of an arrow.
2 Remove the speaker (7.7 cm) (L-CH)
(SP101) in the direction of an arrow.
1 four tapping screws
(BV
B2.6)
red (
+)
white (
−)
– Cabinet (front) block rear left side view –
red (
+)
white (
−)
3 Remove solder
from
the
“
−” terminal.
3 Remove solder
from
the
“
+” terminal.
:ire settinJ
speaker terminal
Twist a wire around
a speaker terminal hole.
a speaker terminal hole.
Install the speaker (7.7 cm) (R-CH)
(SP201) in inside two ribs.
(SP201) in inside two ribs.
Install the speaker
(7.7 cm) (L-CH)
(SP101) in inside
two ribs.
(7.7 cm) (L-CH)
(SP101) in inside
two ribs.
wire
Speaker (7.7 cm) (L-CH) (SP101) settinJ
Speaker (7.7 cm) (R-CH) (SP201) settinJ
:ire settinJ
tape
tape
Click on the first or last page to see other ZS-S10CP service manuals if exist.