Sony ZS-S10CP Service Manual ▷ View online
ZS-S10CP
5
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. CABINET (REAR) ASSY, FUSE (F901, F902)
(Page
(Page
6)
2-3. CABINET
(FRONT)
ASSY
(Page
7)
2-4. MAIN BOARD BLOCK
(Page
(Page
8)
2-9. SPEAKER (7.7 cm)
(SP101,
(SP101,
SP201)
(Page
12)
2-5. MAIN
BOARD
(Page
9)
2-6. CD
BLOCK
ASSY
(Page
10)
2-11. POWER BOARD
(Page
(Page
14)
2-8. CD
SPRING
(Page
11)
2-7. OPTICAL
PICK-UP
(DA11MMVGP)
(OP1)
(Page
10)
2-10. TELESCOPIC ANTENNA (ANT1),
ANTENNA
ANTENNA
SPRING
(Page
13)
ZS-S10CP
6
3 Lift up the hundle.
– Rear side view –
4 Lift up the telescopic
antenna.
1 battery case
lid
block
0 connector
(CN983)
9 connector
(CN304)
8 connector
(CN301)
6 Push down the handle.
2 two tapping screws
(BV
B2.6)
5 six tapping screws
(BV
B2.6)
2 tapping screw
(BV
B2.6)
5 tapping screw
(BV
B2.6)
5 tapping screw
(BV
B2.6)
7 Remove the cabinet (rear) assy
in the direction of an arrow.
qa cabinet (rear) assy
qs fuse (F901)
qd fuse (F902)
MAIN board
HP JACK board
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
:ire seWWiQJ
– Rear ERWWRP side view –
Note: Follow the disassembly procedure in the numerical order given.
2-2. CABINET (REAR) ASSY, FUSE (F901, F902)
ZS-S10CP
7
2-3. CABINET (FRONT) ASSY
3 two tapping screws
(BV
B2.6)
5 cabinet (front) assy
MAIN board
heat sink (AMP)
1 connector
(CN801)
CN801
2 connector
(CN303)
3 two tapping screws
(BV
B2.6)
4 two claws
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
:LUHVHWWLQJ
:LUHVHWWLQJ
MAIN board
heat sink (AMP) MAIN board
C329
–5HDUULJKWVLGHYLHZ–
:LUHVHWWLQJ
MAIN board
wire from BUTTON
(MAIN) board
(MAIN) board
It passes on speaker wire.
wire from MAIN board
speaker wire
speaker wire
speaker wire
CN303
ZS-S10CP
8
2-4. MAIN BOARD BLOCK
Note 1: Before disconnecting the fl exible fl at cable (16 core) of optical pick-up block, solder the short-land.
4 Solder the short-land.
Note 2: When assembling the MAIN
board block, remove the
solder of short-land after
connecting the flexible flat
cable (16 core).
Note 4: When installing the wire, install to numerical order.
cabinet (upper)
5 flexible flat cable (16 core)
1
2
6 flexible flat cable
(6 core) (CN808)
7 MAIN board block
MAIN board
MAIN board
tape
1 connector
(S801)
2 tapping screw
(BV
B2.6)
2 four tapping screws
(BV
B2.6)
3 Remove the MAIN board
block in the direction of
an
arrow.
Note 3: When installing the flexible
flat cable, ensure the coloured
line.
No slanting after insertion.
coloured line
coloured line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
WireVeWWiQJ
–&DEiQeWXSSerEORFNERWWRPViGeYieZ–
Click on the first or last page to see other ZS-S10CP service manuals if exist.