Sony ZS-RS70BT / ZS-RS70BTB Service Manual ▷ View online
ZS-RS70BT/RS70BTB
9
2-4. CABINET (FRONT) BLOCK-2
1 battery lid
2 three tapping screws
(BV
(BV
B2.6)
2 four tapping screws
(BV
(BV
B2.6)
2 tapping screw
(BV
(BV
B2.6)
2 tapping screw
(BV
(BV
B2.6)
3 cabinet (front) block
– Rear view –
– Rear view –
ZS-RS70BT/RS70BTB
10
2-5. SPRING
(CD)
1 Open the CD lid.
4 CD lid assy
6 spring (CD)
spring (CD)
4 shaft
3 shaft
6SULQJ&'VHWWLQJ
6SULQJ&'VHWWLQJ
CD lid
2 Remove the spring
(CD) from the ditch
of CD lid.
ditch
cabinet (upper)
block
block
Spring (CD)
CD lid
3 shaft
ditch
1
Insert the
spring
(CD).
6
Remove the spring (CD) from the ditch of the
cabinet (upper), insert to the ditch of the CD lid.
2
Insert the shaft to the spring (CD).
$VVHPEOLQJSURFHGXUHRIWKHVSULQJ&'
5
Insert the shaft to
the CD lid assy.
CD lid assy
5
Insert the shaft
to the CD lid
assy.
4
Hook the spring (CD) on claw.
–
&DELQHWXSSHUEORFNERWWRPYLHZ–
–
&DELQHWXSSHUEORFNERWWRPYLHZ–
5 claw
3
Hook the spring (CD) to
the ditch temporarily.
–
&DELQHWXSSHUEORFNUHDUYLHZ–
Ver. 1.4
Note: The chucking plate on the bottom side of the CD lid has been deleted in the middle of production.
When replacing the CD lid, refer to “NEW/FORMER DISCRIMINATION OF OPTICAL PICK-UP BLOCK OR CD LID” on page 4.
The fi gures and pictures on this page show the chucking plate attached.
ZS-RS70BT/RS70BTB
11
2-6. CD BLOCK ASSY
2-7. CD BOARD
1 two tapping screws
(PWH
(PWH
B2.6)
1 two tapping screws
(PWH
(PWH
B2.6)
2 CD block assy
– Cabinet (upper) block bottom view –
2 Solder the short-land.
4 Remove four solders.
1 flexible flat cable (27 core) (FFC2)
(CN702)
(CN702)
3 flexible flat cable (16 core)
(CN701)
(CN701)
5 tapping screw
(P
(P
B2.6)
6 CD board
Note 1: Before disconnecting the flexible flat cable (16 core)
of optical pick-up block, solder the short-land.
Note 2:
When assembling the CD board,
remove the solder of short-land
after connecting the flexible flat
cable (16 core).
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 3: When installing the flexible
flat cable, ensure that the
colored line is parallel to the
connector after insertion.
colored line is parallel to the
connector after insertion.
ZS-RS70BT/RS70BTB
12
2-9. RC-S711 (NFC MODULE)
2-8. OPTICAL PICK-UP BLOCK (OP1)
3 claw
3 claw
3 claw
1 vibration proof rubber
(red)
1 vibration proof rubber
(red)
8 optical pick-up
block
(OP1)
optical pick-up
block
block
2 vibration proof
rubber
(green)
(green)
2 vibration proof rubber
(green)
vibration proof rubber
Vibration proof rubber
has become the circle.
has become the circle.
Vibration proof rubber
has become an ellipse.
has become an ellipse.
Upper side
Lower side
9LEUDWLRQSURRIUXEEHUVHWWLQJ
$SSOLFDWLRQSRVLWLRQ
RIWKHERQG
RIWKHERQG
$SSOLFDWLRQSRVLWLRQRIWKHERQG
3 claw
Apply the bond.
OK
NG
5 flexible flat
cable (16 core)
(FFC1)
7 shaft (support)
6 tapping screw
(P2)
Apply the bond.
Apply the bond.
Apply the bond.
–
%RWWRPYLHZ–
–
7RSYLHZ–
4 CD cover
Note
2: Four claws might be fixed
by bond. When installing
the CD cover, please fix
four claws using the bond.
:LUHsetting
1 connector
(CN604)
(CN604)
2 adhesive sheet (NFC)
[red]
[white]
rib
rib
3 RC-S711 (NFC module)
Note
Note
2:
When replacing RC-S711 (NFC module),
please be sure to replace the bluetooth
module simultaneously.
module simultaneously.
RC-S711 (NFC module)
–
&DEinetIURntEORFNUeDUERttRPYieZ–
KEY A board
Note 1: When RC-S711 (NFC module) is replaced, refer to
“NOTE OF REPLACING THE Bluetooth MODULE
OR RC-S711 (NFC MODULE)” on page 5.
OR RC-S711 (NFC MODULE)” on page 5.
Ver. 1.4
Note 1: The optical pick-up block has been changed in the middle of production. When replacing the optical pick-up block, refer to “NEW/FORMER
DISCRIMINATION OF OPTICAL PICK-UP BLOCK OR CD LID” on page 4.
The fi gures and pictures on this page show the former type optical pick-up block.
Click on the first or last page to see other ZS-RS70BT / ZS-RS70BTB service manuals if exist.