Sony ZS-RS70BT / ZS-RS70BTB Service Manual ▷ View online
ZS-RS70BT/RS70BTB
13
2-10. JACK BOARD
:LUHsetting
–&DEinetIURntEORFNUeDUYieZ–
JACK board
tape (sub material)
tape (sub material)
rib
rib
rib
rib
rib
rib
rib
HOLD JACK board
rib
ferrite core
Arrange the wire in the
direction of the arrow.
direction of the arrow.
4 tapping screw
(BV
(BV
B2.6)
4 tapping screw
(BV
(BV
B2.6)
5 HOLD JACK board
5 HOLD JACK board
5 HOLD JACK board
6 JACK board
4 tapping screw
(BV
(BV
B2.6)
1 tapping screw
(PWH
(PWH
B2.6)
3 connector
(CN305)
(CN305)
–&DEinetIURntEORFNUeDUYieZ–
2 ferrite core with wire
ZS-RS70BT/RS70BTB
14
2-11. BLUETOOTH MODULE (BT1)
1 tapping screw
(BV
(BV
B2.6)
2 tapping screw
(P
(P
B2.6)
– Cabinet (front) block rear view –
3 Remove the SOFT board block
in the direction of the arrow.
5 SOFT board block
6 bluetooth module (BT1)
Note
Note
3:
When replacing bluetooth module,
please be sure to replace the
RC-S711 (NFC module) simultaneously.
RC-S711 (NFC module) simultaneously.
4 flexible flat cable (14P)
Flexible flat cable (14P) setting
SOFT board
bluetooth module (BT1)
bluetooth module (BT1)
rib
flexible flat cable (14P)
SOFT board
rib
flexible flat cable (14P)
rib
rib
rib
rib
tape (sub material)
tape (sub material)
tape (sub material)
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible
flat cable, ensure that the
colored line is parallel to the
connector after insertion.
colored line is parallel to the
connector after insertion.
Note 1:
When Bluetooth module is replaced, refer to “NOTE OF
REPLACING THE Bluetooth MODULE OR RC-S711
(NFC MODULE)” on page 5.
REPLACING THE Bluetooth MODULE OR RC-S711
(NFC MODULE)” on page 5.
ZS-RS70BT/RS70BTB
15
2-12. LOUDSPEAKER (7.7 cm) (L/R-CH) (SP101, SP201)
3 loudspeaker (7.7 cm)
(R-ch)
(R-ch)
(SP201)
3 loudspeaker (7.7 cm)
(L-ch)
(L-ch)
(SP101)
2 three tapping screws
(BV
(BV
B2.6)
2 three tapping screws
(BV
(BV
B2.6)
2 tapping screw
(BV
(BV
B2.6)
2 tapping screw
(BV
(BV
B2.6)
– Cabinet (front) block rear view –
1 Remove the solder
from
from
the
“
−” terminal.
[white]
1 Remove the solder
from
from
the
“
−” terminal.
[white]
1 Remove the solder
from
from
the
“
+” terminal.
[red]
1 Remove the solder
from
from
the
“
+” terminal.
[red]
Loudspeaker (7.7 cm) (R-ch) (SP201) setting
Install the loudspeaker (7.7 cm) (R-ch)
(SP201) in inside two ribs.
(SP201) in inside two ribs.
Loudspeaker (7.7 cm) (L-ch) (SP101) setting
Install the loudspeaker (7.7 cm) (L-ch)
(SP101) in inside two ribs.
(SP101) in inside two ribs.
ZS-RS70BT/RS70BTB
16
2-13. TUNER BOARD (RS70BT)/DAB BOARD (RS70BTB)
:LUHVHWWLQJ
:LUHVHWWLQJ
5 tapping screw
(BV
(BV
B2.6)
1 screw
(P M3)
2 telescopic antenna
(ANT1)
(ANT1)
3 connector
(CN903)
(CN903)
4 connector
(CN808)
(CN808)
tape
(sub material)
(sub material)
7 flexible flat cable (11P) (FFC3)
(CN4)
(CN4)
flexible flat cable (11P)
6 Remove the TUNER/DAB board
block in the direction of the arrow.
8 TUNER board (RS70BT)/
DAB board (RS70BTB)
TUNER board (RS70BT)/
DAB board (RS70BTB)
DAB board (RS70BTB)
holder (PWB, TU)
tape (sub material)
tape (sub material)
–
)URQWYLHZ–
rib
rib
ditch
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Click on the first or last page to see other ZS-RS70BT / ZS-RS70BTB service manuals if exist.