Sony STR-DN1010 Service Manual ▷ View online
STR-DN1010
9
2-7 VIDEO BOARD
2-6. DIGITAL BOARD
3
one screw
(+BVTP 3
u8)
5
VIDEO board
6
CONNECTION board
1
one screw
(+BVTP 3
u8)
2
CN804 (18P)
2
CN803 (18P)
4
CN6202
(14P)
4
CN2010 (20P)
4
CN2011 (20P)
9
DIGITAL board
qh
SAIR board
qj
SAIR holder
qf
CN861 (20P)
7
two screws
(+BVTP 3
u8)
5
one screw
(+BVTP 3
u8)
6
one screw
(+BVTP 3
u8)
qs
CN5001 (50P)
qa
four screws
(+BVTP 2.6 (3CR))
0
washer,
valcanized fiber
qg
two screws
(+BVTP 3
u8)
1
CN2008 (7P)
2
CN2014 (4P)
3
CN2016 (3P)
qd
DSP board
8
bracket, HDMI,
right
STR-DN1010
10
2-8. MAIN BLOCK
2-9. MAIN BOARD
Note: This illustration sees the MAIN board from back side.
3
heatsink block
2
two screws
(+BVTP 3
u 8)
4
MAIN board
1
Remove the
forty-two solders.
5
two screws
(+BVTP 3
u8)
1
CN554 (5P)
2
CN553
(3P)
6
one screw
(+BVTP 3
u8)
4
bracket, support (G73)
3
one screw
(+BVTP 3
u8)
7
one screw
(+BVTP 3
u8)
5
two screws
(+BVTP 3
u8)
8
main block
STR-DN1010
11
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US and Canadian models only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
(US and Canadian models only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Press the [– INPUT SELECTOR]/[INPUT SELECTOR +]
buttons to select the “AM TUNER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [DISPLAY] button, press the [
?/1
] button
to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
6. After a few second, “AM 531 kHz” or “AM 530 kHz” appears,
select the desire step.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [DISPLAY] and [A.F.D.] buttons, press the
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [DISPLAY] and [A.F.D.] buttons, press the
[
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears, the set will
power off.
(b) ALL CLEAR INITIALIZE
Procedure:
1. While pressing the [SPEAKERS] and [MUTING] buttons,
Procedure:
1. While pressing the [SPEAKERS] and [MUTING] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “BD” appears after “CLEARED !”.
(c) USER INITIALIZE
Procedure:
1. Hold the [
(c) USER INITIALIZE
Procedure:
1. Hold the [
?/1
] for 5 seconds.
2. The message “CLEARING” appears on the display.
3. After a few seconds, “CLEARED !” appears.
3. After a few seconds, “CLEARED !” appears.
FLUORESCENT INDICATOR TUBE DISPLAY TEST
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
While pressing the [MUTING] and [DISPLAY] buttons, press the
[
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
While pressing the [MUTING] and [DISPLAY] buttons, press the
[
?/1
] button to turn on the main power.
1. ALL segments light on.
LH SW RH
S
SL
SR
L
C
R
SBL
SB SBR
PLII
x z
ANALOG
D.L.L.
A.P.M D.RANGE SIRIUS ST AAC
D.C.A.C. EQ RDS CAT MEM
DTS – HD
'76±(6» LPCM SLEEP
MSTR HI RES LBR
S–AIR ZONE
SP
MHz
k Hz
dB m
A B
3
BI–AMP
HDMI OUT A B
HDMI COAX OPT MULTI ARC
D + EX
HD NEO: 611
True
LFE
2. Press the [DISPLAY] control, confi rm display.
LH
SW
RH
S
SL
SR
L
C
R
SBL
SB
SBR
PLII
x
z
ANALOG
D.L.L.
A.P.M
D.RANGE SIRIUS ST AAC
D.C.A.C. EQ RDS CAT MEM
DTS – HD
'76±(6» LPCM
SLEEP
MSTR HI RES LBR
S–AIR ZONE
SP
MHz
k Hz
dB m
A
B
3
BI–AMP
HDMI OUT A B
HDMI COAX OPT MULTI
ARC
D + EX
HD
NEO: 611
True
LFE
3. Press the [DISPLAY] control, confi rm display.
LH
SW
RH
S
SL
SR
L
C
R
SBL
SB
SBR
PLII
x
z
ANALOG
D.L.L.
A.P.M
D.RANGE SIRIUS ST AAC
D.C.A.C. EQ RDS CAT MEM
DTS – HD
'76±(6» LPCM
SLEEP
MSTR HI RES LBR
S–AIR ZONE
SP
MHz
k Hz
dB m
A
B
3
BI–AMP
HDMI OUT A B
HDMI COAX OPT MULTI
ARC
D + EX
HD
NEO: 611
True
LFE
4. Press the [DISPLAY] control, all segments light off.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [SPEAKERS] and [2CH/A.DIRECT]
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [SPEAKERS] and [2CH/A.DIRECT]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “SWAP MODE” appears (No change while dis-
played).
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [MUTING] and [DIMMER] buttons, press
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [MUTING] and [DIMMER] buttons, press
the [
?/1
] button to turn on the main power.
2. Either the message “C. MODE AV1” or “C. MODE AV2” ap-
pears. Select the desired mode.
PROTECTOR OFF MODE
This mode switching on/off the protector to investigate the cause
of the protector.
Procedure:
1. While pressing the [INPUT MODE] and [A.F.D.] buttons,
This mode switching on/off the protector to investigate the cause
of the protector.
Procedure:
1. While pressing the [INPUT MODE] and [A.F.D.] buttons,
press the [
?/1
] button to turn on the main power.
2. “PROT OFF” appears and switch off the set.
STR-DN1010
12
SIRIUS FACTORY TEST MODE
(US, Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US, Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[DISPLAY] and [2CH/A.DIRECT] buttons, press the [
?/1
]
button to turn on the main power.
2. The message “SIRIUS”, “LOADING” and “SR TUNER” ap-
pear one after another.
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [INPUT MODE] and [2CH/A.DIRECT]
The state that the set is used is memorized.
Procedure:
1. While pressing the [INPUT MODE] and [2CH/A.DIRECT]
buttons, press the [
?/1
] button to turn on the power and “HIS-
TORY” is displayed.
2. Each time the [
M
]/[
m
] buttons on the remote commander is
pressed, the item is switched in order as follows.
Items
Display
Protector count
COUNT XX
Total single power on time
SxxxxxHxxM
Sound fi eld
SOUNDFIELD
Input function
FUNCTION
Input mode
INPUT MODE
Digital select
DIG SELECT
Stream information
STREAMINFO
Signal confi guration
CONF xxxxx
Headphones
HEADPH xxx
Volume
VOL 00 xx
Bass
BASS xxxdB
Treble
TREB xxxdB
Level FL/FR
FL/R xxxxxx
Level SL/SR
SL/R xxxxxx
Level CT/SW
C/SW xxxxxx
Level BL/BR
BL/R xxxxxx
Total power on time
T OHOM
Muting
MUTING xxx
Power on counter
(Rebox test mode)
(Rebox test mode)
REBOX 0
Protector status
PROT xxxx
Temperature status
TEMP xxxc
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN2007) on the DIGITAL board.
2. While pressing the [SPEAKERS] and [MUSIC] buttons, press
the [
?/1
] button to turn on the main power.
3. The message “DMPORT T.” and “DMPORT OK” appears on
the fl uorescent indicator tube and enter the digital media port
test mode (Confi rmation of communication line).
test mode (Confi rmation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [
.
] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
x
] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
DIGITAL board
CN2007
MAIN board
TB506
VIDEO board
J6004
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [MUSIC] buttons,
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [MUSIC] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “N1 ** MX.XX” appears.
**: Destination
Each time the [DISPLAY] button is pressed, “F.Ver X.XX”,
“H.Ver X.XX” and “S.Ver X.XXNII” this order, and returns to
the “N1 ** MX.XX” displayed.
“H.Ver X.XX” and “S.Ver X.XXNII” this order, and returns to
the “N1 ** MX.XX” displayed.
Click on the first or last page to see other STR-DN1010 service manuals if exist.