Sony STR-DN1010 Service Manual ▷ View online
STR-DN1010
13
KEY CHECK MODE
Button check.
Procedure:
1. While pressing the [INPUT MODE] and the [MUTING] but-
Button check.
Procedure:
1. While pressing the [INPUT MODE] and the [MUTING] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “REST 11” appears.
Every pressing of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
displayed.
not counted again. When all buttons are pressed “REST 00”
displayed.
SPDIF UPDATE MODE
User plays the CD that contains u-com/DSP data with CD/DVD
player.
Update u-com/DSP etc. fi rmware from SPDIF input.
Connection:
User plays the CD that contains u-com/DSP data with CD/DVD
player.
Update u-com/DSP etc. fi rmware from SPDIF input.
Connection:
CD/DVD
player
DIGITAL board
TV OPTICAL IN jack (IC2004)
TV OPTICAL IN jack (IC2004)
set
Procedure:
Normal case
1. While pressing [DIMMER] button, press the [
Normal case
1. While pressing [DIMMER] button, press the [
?/1
] button to
turn on the main power.
2. The messages “UPDATE” and “PLAY DISC” are displayed
alternately every one second.
After this step, all user operation is prohibited except power
off. To cancel this mode, power off or AC power cord pull out
is required.
off. To cancel this mode, power off or AC power cord pull out
is required.
3. Connect CD player to TV OPTICAL IN jack (IC2004 on the
DIGITAL board), and play update CD.
Update is started when DSP detect update signal. The message
“UPDATING” is displayed blinks every one second.
“UPDATING” is displayed blinks every one second.
From this step, all user operation is prohibited. Power off is
also prohibited.
also prohibited.
4. While main u-com is being updated, fl uorescent indicator tube
is blacked out.
5. When update data error is detected or disc is not matched with
target model, error messages “DISC ERROR” and “PLAY
DISC” are displayed to restart playing valid CD.
DISC” are displayed to restart playing valid CD.
When
fl ash writing error is happened, error messages “UP-
DATE ERR” and “PLAY DISC” are displayed to restart play-
ing CD.
ing CD.
6. When all update is fi nished, set is reboot automatically. After
reboot, complete message “COMPLETE” is displayed (dis-
played continuously until any user operation).
played continuously until any user operation).
Procedure:
After update is abnormal exit, and set is power on again
1. Enter update mode automatically after power on.
2. The messages “UPDATE” and “PLAY DISC” are displayed
After update is abnormal exit, and set is power on again
1. Enter update mode automatically after power on.
2. The messages “UPDATE” and “PLAY DISC” are displayed
alternately every one second.
From this step, all user operation is prohibited. Power off is
also prohibited.
also prohibited.
If main u-com was failed to update, nothing is displayed.
3. Connect CD player to TV OPTICAL IN jack (IC2004 on the
DIGITAL board), and play update CD.
Update is started when DSP detect update signal. From this,
same as normal case.
same as normal case.
VERSION CHECK
Function that displays the version number to check whether SPDIF
update is necessary or not.
Procedure:
1. While pressing [MUTING] button, press the [
Function that displays the version number to check whether SPDIF
update is necessary or not.
Procedure:
1. While pressing [MUTING] button, press the [
?/1
] button to
turn on the main power.
2. The message “VER X.XXX” is displayed. “X.XXX” is calcu-
lated by adding all fi rmware version.
Example:
(MAIN ver. + DSP ver. + HDMI ver. + FARO ver. + 6)/10 =
Displayed version
Displayed version
MAIN = 1.02, DSP = 1.01, HDMI = 1.00, FARO = 1.03
↓
(1.02 + 1.01 + 1.00 + 1.03 + 6)/10 = 1.006
1.006 = X.XXX
SPDIF UPDATE CHECK
Function that checks hardware error for SPDIF update.
This test takes about 15 seconds.
Procedure:
1. While pressing [DIMMER] and [2CH/A.DIRECT] buttons,
Function that checks hardware error for SPDIF update.
This test takes about 15 seconds.
Procedure:
1. While pressing [DIMMER] and [2CH/A.DIRECT] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “TESTING” is displayed and LED (MULTI
CHANNEL DECODING indicator) is blinking.
3. When abnormality is not found, the message disappears and
LED is light up.
4. Communication error between main microcomputer and DSP,
the messages “UART” and “ERROR” are displayed and LED
is blinking in fast speed.
is blinking in fast speed.
Communication error between HDMI microcomputer and
DSP, the messages “HDMI” and “ERROR” are displayed and
LED is blinking in fast speed.
LED is blinking in fast speed.
Communication error between Faraudja and DSP, the messages
“VIDEO” and “ERROR” are displayed and LED is blinking in
fast speed.
“VIDEO” and “ERROR” are displayed and LED is blinking in
fast speed.
Unknown error, the messages “UNKNOWN” and “ERROR”
are displayed and LED is blinking in fast speed.
are displayed and LED is blinking in fast speed.
5. To release from this mode, AC power cord pull out.
Note: SPDIF UPDATE MODE, VERSION CHECK and SPDIF UPDATE
CHECK are supported with DSP version 1.02 or later.
DCAC TEST MODE
Procedure:
1. While pressing the [INPUT MODE] and the [MOVIE] but-
Procedure:
1. While pressing the [INPUT MODE] and the [MOVIE] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “SOURCE” or “MIC” appears.
SOURCE: normal mode
MIC: mode that output audio from mic input
MIC: mode that output audio from mic input
STR-DN1010
14
SECTION 4
ELECTRICAL ADJUSTMENT
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Note: After replacing DIGITAL VIDEO board, or after “RESET” of the
special menu mode is executed, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
2. Video calibration adjustment
2-1. Connection
2-1. Connection
color pattern
generator
or
Blu-ray
Disc player
set
HDMI TV
OUT
ANALOG VIDEO board
COMPONENT VIDEO ASSIGNABLE
(INPUT ONLY) COMPO 1 IN jack
BD VIDEO IN jack
2-2. Procedure for color pattern generator
1. It connects of step 2-1, and the turn on the main power.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [MOVIE] and [DISPLAY] buttons, press
1. It connects of step 2-1, and the turn on the main power.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [MOVIE] and [DISPLAY] buttons, press
the [POWER] button to turn on the main power. When cor-
rectly entering the test mode “FIN _:_:_” is displayed (keeps
pressing two buttons until the message appears).
rectly entering the test mode “FIN _:_:_” is displayed (keeps
pressing two buttons until the message appears).
6. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the dis-
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
tern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. The turn off the main power.
11. The turn off the main power.
2-3. Procedure for Blu-ray Disc player
1. It connects of step 2-1, and the turn on the main power of set
1. It connects of step 2-1, and the turn on the main power of set
and Blu-ray Disc player.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
3. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
DVD test disc “HLX-504 (Part No. J-6090-088-A)” or “HLX-
513 (Part No. J-2501-305-A)” is insert. The disc playback au-
tomatically becomes start “Main Menu” is display.
513 (Part No. J-2501-305-A)” is insert. The disc playback au-
tomatically becomes start “Main Menu” is display.
4. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
5. Press the [POWER] button to turn off the main power of the
set.
6. While pressing the [MOVIE] and [DISPLAY] buttons, press
the [POWER] button to turn on the main power of the set.
When correctly entering the test mode “FIN _:_:_” is dis-
played (keeps pressing two buttons until the message appears).
When correctly entering the test mode “FIN _:_:_” is dis-
played (keeps pressing two buttons until the message appears).
7. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the dis-
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
8. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
change to DVD test disc “HLX-506 (Part No. J-6090-077-A)”
or “HLX-507 (Part No. J-6090-078-A)”. The disc playback au-
tomatically becomes start “Main Menu” is display.
or “HLX-507 (Part No. J-6090-078-A)”. The disc playback au-
tomatically becomes start “Main Menu” is display.
9. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
10. The PAL signal adjustment is begun when press the cross (cen-
ter of cursor) button of remote commander. Finally, the display
returns to the display of “FIN N:P:_”.
returns to the display of “FIN N:P:_”.
11. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
change to DVD test disc “HLX-104 (Part No. J-6090-199-A)”.
The disc playback automatically becomes start “Main Menu”
is display.
The disc playback automatically becomes start “Main Menu”
is display.
12. “59.94Hz, 1080i” → “1.Video Signal” → “1.Color Bar 100%”
is selected, and 100% in the color bar is displayed in the TV
monitor, playing the Blu-ray Disc player is pause playback.
monitor, playing the Blu-ray Disc player is pause playback.
13. The video output of the Blu-ray Disc player is switched 1080i
(The output from the component terminal of the Blu-ray Disc
player becomes 1080i output).
player becomes 1080i output).
14. The HD signal adjustment is begun when press the cross (cen-
ter of cursor) button of remote commander. Finally, the display
returns to the display of “FIN N:P:H”.
returns to the display of “FIN N:P:H”.
15. The turn off the main power.
STR-DN1010
15
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
STR-DN1010
16
SECTION 5
DIAGRAMS
• Circuit Boards Location
TUNER (FM/AM)
DIGITAL board
STANDBY DCDC Board
POWER KEY board
HEADPHONE board
DISPLAY board
THERMAL SENSOR board
MAIN board
DSP board
CONNECTION board
VIDEO board
SAIR board
DIGITAL VIDEO board
Click on the first or last page to see other STR-DN1010 service manuals if exist.