Sony STR-DN1000 Service Manual ▷ View online
STR-DN1000
9
(US, CND)
3
screw
(BVTT3
u 6)
1
six screws
(BVTP3
u 8)
4
back panel
1
five screws
(BVTP3
u 8)
2
four screws
(BV/RING)
1
four screws
(BVTP3
u 8)
1
five screws
(BVTP3
u 8)
2-9. DSP BOARD, DIGITAL BOARD, VIDEO BOARD
Note:
This illustration sees the set from rear side.
2-8. BACK PANEL
Note:
This illustration sees the set from rear side.
• Abbreviation
CND : Canadian model
CND : Canadian model
1
four screws
(BVTP2.6)
3
DSP board
q;
screw (BVTP3
u 8)
qg
screw (BVTP3
u 8)
qf
DIGITAL board
6
wire (flat type) (25 core)
(CN2012)
5
wire (flat type) (29 core)
(CN2007)
4
wire (flat type) (9 core) (except AEP, UK)
(CN2003)
wire (flat type) (11 core) (AEP, UK)
(CN2002)
qg
screw
(BVTP3
u 8)
7
connector
(CN2016)
qj
VIDEO board
qs
two screws (BVTP3
u 8)
qd
right HDMI bracket
8
connector (CN2014)
9
connector (CN2008)
qh
connector (CN6202)
2
connector
(CN5001)
qa
two connectors
(CN2010,
CN2011)
STR-DN1000
10
2-11. MAIN BOARD
Note: This illustration sees the MAIN board from back side.
3
heatsink block
4
fuse (T6.3AL/250V)
(F404)
5
fuse (T6.3AL/250V)
(F403)
2
two screws
(BVTP3
u 8)
6
MAIN board
1
Remove the
forty-two
solders.
2-10 CONNECTION BOARD, MAIN BLOCK
Note: This illustration sees the set from rear side.
2
wire (flat type) (9 core)
(CN805)
4
screw (BVTP3
u 8)
5
support (G73)
bracket
4
two screws
(BVTP3
u 8)
4
two screws
(BVTP3
u 8)
4
screw
(BVTP3
u 8)
3
saranet
cushion
8
main block
1
connector
(CNP300)
7
CONNECTION board
6
two connectors
(CN803,
CN804)
STR-DN1000
11
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US, Canadian, Chilean, Peruvian and Australian models
only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
(US, Canadian, Chilean, Peruvian and Australian models
only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Turn the [– INPUT SELECTOR]/[INPUT SELECTOR +] but-
tons to select the “AM TUNER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [DISPLAY] button, press the [
?/1
] button
to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUTING] and [SPEAKERS] buttons,
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUTING] and [SPEAKERS] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears.
FLUORESCENT INDICATOR TUBE DISPLAY TEST
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [MUTING] and [DISPLAY] buttons, press
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [MUTING] and [DISPLAY] buttons, press
the [
?/1
] button to turn on the main power.
2. All segments and all LEDs turn on. Each time [DISPLAY] but-
ton to change as follow all on, test pattern 1, test pattern 2, all
off, all on in this order.
off, all on in this order.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MUSIC] and [2CH/A.DIRECT] buttons,
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MUSIC] and [2CH/A.DIRECT] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “SWAP MODE” appears (No change while dis-
played).
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [MUTING] and [MUSIC] buttons, press
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [MUTING] and [MUSIC] buttons, press
the [
?/1
] button to turn on the main power.
2. Either the message “C. MODE AV1” or “C. MODE AV2” ap-
pears. Select the desired mode.
SIRIUS FACTORY TEST MODE
(US, Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US, Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[DISPLAY] and [2CH/A.DIRECT] buttons, press the [
?/1
]
button to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
kHz L and 1 kHz R are switched.
Ver. 1.1
STR-DN1000
12
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [INPUT MODE] and [2CH/A.DIRECT]
The state that the set is used is memorized.
Procedure:
1. While pressing the [INPUT MODE] and [2CH/A.DIRECT]
buttons, press the [
?/1
] button to turn on the power and “HIS-
TORY” is displayed.
2. Each time the [
M
]/[
m
] buttons on the remote commander is
pressed, the item is switched in order as follows.
Items
Display
Protector count
COUNT XX
Total single power on time
SxxxxxHxxM
Sound fi eld
xxxxxxxxxx
Input function
xxxxxxxxxx
Input mode
xxxxxxxxxx
Digital select
xxxxxxxxxx
Stream information
xxxxxxxxxx
Signal confi guration
CONF xxxxx
Headphones
HEADPH xxx
Volume
VOL xx
Bass
BASS xxxdB
Treble
TREB xxxdB
Level FL/FR
FL/R xxxxxx
Level SL/SR
SL/R xxxxxx
Level CT/SW
C/SW xxxxxx
Level BL/BR
BL/R xxxxxx
Total power on time
TxxxxxHxxM
Muting
MUTING xxx
Power on counter
(Rebox test mode)
(Rebox test mode)
REBOX xxxx
Protector status
PROT xxxx
Temperature status
TEMP xxxc
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN2007) on the DIGITAL board.
2. While pressing the [SPEAKERS] and [MUSIC] buttons, press
the [
?/1
] button to turn on the main power.
3. The message “DMPORT T.” and “DMPORT OK” appears on
the fl uorescent indicator tube and enter the digital media port
test mode (Confi rmation of communication line).
test mode (Confi rmation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [
.
] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
x
] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
DIGITAL board
CN2007
MAIN board
TB506
VIDEO board
J6004
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [SPEAKERS] but-
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [SPEAKERS] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “N1 ** MX.XX” appears.
**:
**:
Destination
Each time the [DISPLAY] button is pressed, “H.Ver X.XX”,
“V.Ver _._ _”, “G.Ver _._ _”, “F.Ver X.XX” and “S.Ver X.XX”
this order, and returns to the “N1 ** MX.XX” displayed.
“V.Ver _._ _”, “G.Ver _._ _”, “F.Ver X.XX” and “S.Ver X.XX”
this order, and returns to the “N1 ** MX.XX” displayed.
Ver. 1.1
Click on the first or last page to see other STR-DN1000 service manuals if exist.