Sony STR-DA6400ES Service Manual ▷ View online
STR-DA6400ES
21
3-8. ANALOG BOARD
screw
(B3
× 6)
seven screws
(BVTP3
× 8)
screw
(BVTP3
× 8)
three connectors
(CN605, CN606, CN608)
wire (flat type) (9core)
(CN603)
screw
(BVTP3
× 8)
bracket (side)
R ANALOG board
reinforcement
(main)
(US)
3-9. HEAT SINK BLOCK
connector
(CN1405)
two connectors
(CN1207,
CN1209)
two connectors
(CN1205,
CN1206)
seven screws
(BV3
× 8 CU)
CONNECTOR1 board
heat sink block
CONNECTOR2 board
Ver. 1.1
STR-DA6400ES
22
3-10. POWER TRANSFORMER (T1), E-VOL/MAIN BOARDS
RL four screws
(BVTP3
× 8)
RG lead wire with connector
(CN1001)
RI two lead wires
X screw
(BVTP3
× 8)
RM three screws
(BV/ring)
RH Cut the
binding band (taiton).
RH Cut the
binding band (taiton).
two screws
(BVTP3
× 8)
XT three screws
(BVTP3
× 8)
RK two accessory
screws
(J1499)
RE two fuses (T4AL/250V)
(F1403,
F1404)
J1499
screw
(BVTP3
× 8)
R screw
(BVTP3
× 8)
RB reinforcement
(DM/MAIN)
XB reinforcement (MAIN)
RT E-VOL board
XE MAIN board
bracket
(SS)
four copper washer
+BVTT
assies
label (TR-ES/L)
power
transformer
(T1)
(T1)
two connectors
(CN1404,
CN1408)
two connectors
(CN1208,
CN1209)
two connectors
(CN1203,
CN1204)
STR-DA6400ES
23
SECTION 4
TEST MODE
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [MUSIC] and joy stick enter buttons, press
The state that the set is used is memorized.
Procedure:
1. While pressing the [MUSIC] and joy stick enter buttons, press
the [POWER] button to turn on the power and “HISTORY
MODE” is displayed.
MODE” is displayed.
2. Each time up or down jog switch, the item is switched in order
as follows.
Items
Display
Number of protector is gener-
ated
ated
PRCT COUNT: XXX
Total use time
TTL_TIME: XXXXH XXM
Sound fi eld
XXXXXXXXXXXXXXXX
Input Selector
INPUT: XXXXXXXXXX
Input mode
INMODE: XXXXXXXXXXXX
Input mode under lock state
DSEL: XXXXXXXXXXXXXXX
Stream under input
STREAM: XXXXXXX
Channel information
CONFIG:XXXXXXX
State of headphone
HEAD PHONES: XXX
Volume
VOL:
XXXdB
EQ setting value
BASS: XXXdB
TREB: XXXdB
TREB: XXXdB
Level collection value
each channel
each channel
Lv FL/FR XXXX/XXXX
Lv SL/SR XXXX/XXXX
Lv CT/SW XXXX/XXXX
Lv BL/BR XXXX/XXXX
Lv SL/SR XXXX/XXXX
Lv CT/SW XXXX/XXXX
Lv BL/BR XXXX/XXXX
Total time of power on
TTL_P_ON: XXXXH XXM
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN6751) on the NETWORK board.
2. While pressing the [A.F.D.] and [MENU] buttons, press the
[POWER] button to turn on the main power.
3. The message “DMPORT OK.” appears on the fl uorescent in-
dicator tube and enter the digital media port test mode (Confi r-
mation of communication line).
mation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [
.
] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
x
] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
NETWORK board
CN6751
MAIN board
TM4002
A-VIDEO board
J6001
XM FACTORY TEST MODE (US model only)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.
turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
kHz L and 1 kHz R are switched.
SIRIUS FACTORY TEST MODE (US model only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [POWER]
button to turn on the main power.
button to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 kHz L/R, 10 Hz L/R, noise L,
noise R, muting are switched.
noise R, muting are switched.
Ver. 1.1
STR-DA6400ES
24
FLUORESCENT INDICATOR TUBE PATTERN CHECK
MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [MOVIE] and [MENU] buttons, press the
MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [MOVIE] and [MENU] buttons, press the
[POWER] button to turn on the main power.
2. All segments and all LEDs turn on. Each time [DISPLAY] but-
ton to change as follows all on, test pattern 1, test pattern 2, all
off, all on in this order.
off, all on in this order.
S.F LOCK ON/OFF CHANGE MODE
Procedure:
1. While pressing the [MUSIC] and [MENU] buttons, press the
Procedure:
1. While pressing the [MUSIC] and [MENU] buttons, press the
[POWER] button to turn on the main power.
2. Either the message “SF LOCK [OFF]” or “SF LOCK [ON]”
appears.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
ton to turn on the main power.
2. The message “S. F. Initialize” appears and initialization is per-
formed.
TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE
(US model only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the
(US model only)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the
[POWER] button to turn on the main power.
5. Either the message “AM 9k Step” or “AM 10k Step” appears,
select the desired step.
MEMORY CLEARING MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [HDMI IN] buttons,
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [HDMI IN] buttons,
press the [POWER] button to turn on the main power.
2. The message “MEMORY CLEARING***” appears and the
memories are reset to the default values.
3. When done, the message “MEMORY CLEARED*” appears.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the [POW
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the [POW
ER] button to turn on the main power.
2. Either the message “COMMAND MODE [AV1]” or “COM
MAND MODE [AV2]” appears. Select the desired mode.
Ver. 1.1
Click on the first or last page to see other STR-DA6400ES service manuals if exist.