DOWNLOAD Sony STR-DA5700ES Service Manual ↓ Size: 21.18 MB | Pages: 127 in PDF or view online for FREE

UPDATE  OF  SOFTWARE  OF  IC6302  ON  THE  A-VIDEO  
BOARD,  IC3601  ON  THE  D-VIDEO  BOARD,  IC2501  
ON  THE  CONTROL  BOARD  AND  IC763  ON  THE  DIS-
PLAY  BOARD
Perform operation of the following when the update of software 
of the IC6302 on the A-VIDEO board, IC3601 on the D-VIDEO 
board, IC2501 on the CONTROL board and IC763 on the DIS-
PLAY board are necessary.

Procedure:
1.  Connect the RS232C terminal on rear side of this unit (J861 on 

the HAT board) and PC by using the RS-232C cable.

2.  Press the [\/1] button to turn on the main power.
3.  The update is executed by using application on PC.
4.  When the update ends, press the [\/1] button to turn off the 

main power.

5.  Remove the RS-232C cable from the the RS232C terminal on 

rear side of this unit (J861 on the HAT board) and PC.

You can check the status of the receiver by the 
message. See the following table to solve the 
problem.

The receiver is covered and ventilation holes 
are blocked. The receiver will automatically 
turn off after a few seconds. Remove the 
object covering the upper panel of the 
receiver and turn on the power again.

Irregular current is output to the speakers 
due to a short circuit on the speaker 
terminals. The receiver will automatically 
turn off after a few seconds. If the protective 
device on the receiver is activated due to a 
short-circuit problem, turn off the receiver. 
Check the connection of the speakers and 
turn on the power again.

Check that the ventilation hole on the top of 
the receiver are not blocked. Place the 
receiver in a location with adequate 
ventilation to prevent heat build-up in the 
receiver.

Update the receiver to a newer software 

‡ If you use the receiver in main zone, 

connect the receiver to a TV via an HDMI 
cable.

‡ If you connect the receiver to a TV via a 

video cord, set “Playback Resolution” to 
“480i/576i”.

‡ If you connect the receiver to a TV via a 

component video cord, set “Playback 
Resolution” to a parameter appropriate to 
your TV.

Error messages

Before using the receiver for the first time, 
initialize the receiver by performing the 
following procedure. This procedure can also 
be used to revert back to the factory default 
settings.

1

Press ?/1 to turn off the 
receiver.

2

While holding down the TONE 
MODE and 2CH/A.DIRECT, 
press ?/1 to turn on the 
receiver.

3

The “MEMORY CLEARING...” appears 
on the display window for a while, then 
changes to “MEMORY CLEARED!”
Changes or adjustments made to the 
settings are now reset to the defaults.

It takes about one minute for the memory to be 
cleared completely. Do not turn the receiver off until 
“MEMORY CLEARED!” appears on the display.

Performing initial setup 

operations (clearing all 

memorized settings)

?

/1

TONE MODE

2CH/A.DIRECT

version. 

Note: When this confi rmation is executed, IP address is changed.

Necessary machinery and materials:
• 

PC (Windows XP/Vista)

• Router
 

(Transmission rate is 100 Mbps or more, built-in DHCP server 
function)

• 

Two LAN cables

 

(Category 5 cable, normal type or shield type)

• Monitor
• 

Supplied multifunction remote commander (RM-AAL040)

Connection:
(The router need not be connected with the internet)

Procedure:
1.  The setting of LAN of PC is setting to the automatic IP address 

assignment. 

 

It changes to the setting that displays the image in the monitor.

2.  Perform connection with reference to connection fi gure.
3.  The power supply of the router is turn on, next, the power sup-

ply of PC and this unit is turn on.

4.  Press the [HOME] button of the remote commander, the home 

menu is displayed in the monitor.

5.  The “Settings” is selected on the home menu, and press the [

] 

button of remote commander.

6.  The “Network Settings” is selected , and press the [

] button 

of remote commander.

7.  The “Internet Settings” is selected , and press the [

] button of 

remote commander.

8.  The “Network Setup” is selected , and press the [

] button of 

remote commander.

9.  The “Auto” is selected , and press the [

] button of remote 

commander.

10. The “Setup Cnfi rmation” is displayed , and press the [

,

] but-

ton of remote commander.

11.  The “Save & Connect” is selected , and press the [

] button of 

remote commander.

12. The automatically connect function is performed.
13. Confi rm that the “Internet Access:   OK” has been displayed,  

and press the [

] button of remote commander.

14. Press the [\/1] button to turn off the main power.

NOTE  OF  REPLACING  THE  NETWORK  BOARD
When the NETWORK board is exchanged, the MAC address has 
been changed.
Please print and cut out the following explanations, and return it 
with the unit that completes the repair.

MAC address of this receiver has been changed by this repair. 
The customer who uses the MAC address fi ltering function of 
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the System Information screen 
of this unit. Please refer to “Adjusting Settings” on the operating 
instructions for details.

NOTE  OF  REPLACING  THE  IC2239  ON  THE  D-AUDIO 
BOARD  AND  THE  COMPLETE  D-AUDIO  BOARD 
(AEP and UK models only)
When this unit is connected with PC, this unit is recognized as a 
USB audio device on PC. At this time, the manufacture maker’s 
information, etc. (USB descriptor) are transmitted to PC from this 
unit. The USB descriptor is stored in the IC2239 on the D-AUDIO 
board, and it is written in at the factory.
When the IC2239 on the D-AUDIO board or the complete D-AU-
DIO board are exchanged, do the following work.

1. Preparation
Prepare the following before beginning work.

• 

Windows PC (Windows XP or Vista)

• 

USB cable (A type plug to B type plug)

 
• 

Writing utility software (.exe fi le)

• 

USB descriptor defi nition fi le (.txt fi le)

Note: Confi rm the method of obtaining the writing utility software and 

USB descriptor defi nition fi le to each service headquarters.

2. Writing method
Procedure:
1.  Assemble to this unit the D-AUDIO board to which exchange 

of the IC2239 or D-AUDIO board exchange for the new.

2.  Connect PC and this set with USB cable.

3.  Press the [\/1] button on this unit to turn on the main power.
 

(It is not necessary to wait for memory clearing)

4. Run 

the 

writing utility software on PC.

5.  Click the “Read From File” button of the writing utility soft-

ware on PC and open the USB descriptor defi nition fi le.

6.  Click the “Save To EEPROM” button.

7.  Click the “Write” button.

8.  After “Save Data To EEPROM” window disappears, wait for 

about 2 seconds.

9.  After about 2 seconds, the writing of the USB descriptor to the 

IC2239 on the D-AUDIO board is completed.

3. Checking method
Procedure:
1.  Open the Device Manager of windows on PC.
2.  Expand the “Sound, video and game controllers”, and right-

click on the “AV RECEIVER”, “AV AMPLIFIER” or “USB 
Audio Device” and select the “Properties”.

3.  Click the “Details” tab, and select the “Hardware Ids” from pull-

down list on Property. Check that the part surrounded by the 
dotted line of the following fi gure is “VID_054C&PID_05C1”.

Property

Value

AV RECEIVER

Hardware Ids

USB\VID_054C&PID_05C1&REV_0001&MI_01
USB\VID_054C&PID_05C1&MI_01

4.  The checking was completed.

CAPACITOR  ELECTRICAL  DISCHARGE  PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitors (C905 on 
the ACDC board) to discharge the capacitors (C905 on the ACD-
Cboard).

:/2 W

1

2.00_12_M

J-2501-357-A

2.0

12

For E-VOL Board (CN1201)

2.00_12_M

For A-CLASS_AMP Board (CN1504)

PH cable 12P

J-2501-352-A

Length 300 mm

2

2.00_16_M

J-2501-358-A

2.0

16

For E-VOL Board (CN1202)

2.00_16_M

For A-CLASS_AMP Board (CN1505)

PH cable 7P

J-2501-353-A

Length 300 mm

PH cable 9P

POWER  AMP  BLOCK  SERVICE  POSITION
• 

Please connect following extension jig.

Connect extension jig 2 to the 
A-CLASS_AMP board (CN1505) 
and E-VOL board (CN1202).

Connect extension jig 1 to the 
A-CLASS_AMP board (CN1504) 
and E-VOL board (CN1201).

3

1.25_14_F

J-2501-354-A

1.25

14

For CONTROL Board (CN2921)

1.25_14_F

For D-AUDIO Board (CN2201)

FFC cable 14P

J-2501-361-A

Length 300 mm

4

1.25_26_F

J-2501-356-A

1.25

26

For CONTROL Board (CN2891)

1.25_26_F

For D-AUDIO Board (CN2202)

FFC cable 26P

J-2501-365-A

Length 300 mm

5

1.25_14_M

J-2501-344-A

1.25

14

For MAIN Board (CN1006)

1.25_14_F

For CONTROL Board (CN2701)

FFC cable 14P

J-2501-361-A

Length 300 mm

6

1.25_20_M

J-2501-345-A

1.25

20

For MAIN Board (CN1005)

1.25_20_F

For CONTROL Board (CN2721)

FFC cable 20P

J-2501-363-A

Length 300 mm

CONTROL  BOARD  SERVICE  POSITION
• 

Please connect following extension jig.

Connect extension jig 6
to the CONTROL board (CN2721) 
and MAIN board (CN1005).

Connect extension jig 5
to the CONTROL board (CN2701) 
and MAIN board (CN1006).

Connect extension jig 3
to the CONTROL board (CN2921) 
and D-AUDIO board (CN2201).

Connect extension jig 4
to the CONTROL board (CN2891) 
and D-AUDIO board (CN2202).

Note: Connect altogether the metal part
 

on the boards connected with the

 

chassis using the alligator clip.