Sony STR-DA5700ES Service Manual ▷ View online
STR-DA5700ES
21
2-15. TUNER (FM/AM) (TU1)
2-14. CONTROL BOARD
1
connector
(CN2701)
4
connector
(CN2700)
5
connector
(CN2961)
6
connector
(CN2981)
2
connector
(CN2721)
3
Lift up the CONTROL board
in the direction of an arrow.
9
CONTROL board
7
two screws
(BVTP3
u 8)
8
two brackets
(control)
2
three screws
(BVTP3
u 8)
3
Lift up the tuner block in
the direction of an arrow.
1
wire (flat type)
(US, Canadian: 9 core/AEP, UK: 11 core)
4
bracket (TU-P)
5
tuner (FM/AM)
(TU1)
STR-DA5700ES
22
2-16. A AUDIO BOARD-1
lead pin
lead pin
lead pin
lead pin
lead pin
lead pin
:LUHVHWWLQJ
A AUDIO board
lead pin
A AUDIO board
A AUDIO board
MAIN board
rear side
rear side
rear side
3
connector
(CN602)
4
connector
(CN605)
5
connector
(CN607)
6
connector
(CN608)
7
connector
(CN606)
8
connector
(CN611)
2
Wire is removed from four lead pins.
(See Fig. E, F, G)
2
Wire is removed from two lead pins.
(See Fig. F)
2
Wire is removed from the lead pin.
(See Fig. E)
2
Wire is removed from the lead pin.
(See Fig. E)
1
wire (flat type)
(US, Canadian: 9 core CN604
/AEP, UK: 11 core CN603)
)LJ(!
)LJ)!
)LJ*!
STR-DA5700ES
23
2-18. BRACKET (LARGE) BLOCK, FUSE (F1403, F1404)
• Left front side view
2-17. A AUDIO BOARD-2
3
six screws
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
3
screw
(BVTP3
u 8)
4
screw
(P3
u 6)
2
bracket (PWB)
5
A AUDIO board
(US, Canadian)
1
Wire is removed from
the clamp (L35).
4
fuse (F1403)
5
fuse (F1404)
3
bracket (large) block
2
two screws
(BVTP3
u 8)
clamp (L35)
SPTM board
bracket (large)
:LUHVHWWLQJ
rear side
STR-DA5700ES
24
2-19. DCDC2 BOARD
(AEP, UK)
(AEP, UK)
6
Cut two binding bands (taiton).
(See Fig. J)
1
Cut the binding band (taiton).
(See Fig. I)
binding band
(taiton)
(taiton)
binding band
(taiton)
(taiton)
binding band
(taiton)
(taiton)
binding band
(taiton)
(taiton)
binding band (taiton)
1
Cut the binding band (taiton).
(See Fig. I)
1
Cut two binding bands (taiton).
(See Fig. H, K)
2
two sleeve
ferrite
clamps
sleeve ferrite clamp
7
clamp filter (ferrite core)
clamp filter
(ferrite core)
(ferrite core)
Note: In reassembling, use new binding band (taiton)
to fasten the clamp same as before.
4
two screws
(BVTP3
u 8)
5
Lift up the DCDC2 board in
the direction of an arrow.
0
DCDC2 board
DCDC2 board
8
connector
(CN3702)
9
connector
(CN3701)
:LUHVHWWLQJ
front side
front side
DCDC2 board
MAIN board
DCDC2 board
86&DQDGLDQ
binding band
(taiton)
(taiton)
heat sink
heat sink
clamp (L35)
front side
front side
front side
)LJ+!
)LJ-!
)LJ,!
)LJ,!
)LJ.!
clamp (L35)
3
Wire is removed from the clamp (L35).
(See Fig. I)
Note: Process so that lead wire does not
contact heat sink.
Note: Process so that lead wire or sleeve ferrite clamp
does not contact heat sink.
SAFETY STANDARD
SAFETY STANDARD
Click on the first or last page to see other STR-DA5700ES service manuals if exist.