Sony STR-DA5600ES Service Manual ▷ View online
STR-DA5600ES
21
2-19. MAIN BOARD
Note: In reassembling, use new binding band (taiton)
to fasten the clamp same as before.
5
connector
(CN1401)
0
connector
(CN1001)
qa
MAIN board
3
Cut two binding bands (taiton).
9
Cut the binding
band
(taiton).
4
clamp filter (ferrite core)
6
screw
(BVTP3
u 8)
7
reinforcement (main)
6
three screws
(BVTP3
u 8)
2
fuse (F1404)
1
fuse (F1403)
8
MAIN board
MAIN board
:LUHVHWWLQJ
rear
rear
STR-DA5600ES
22
SECTION 3
TEST MODE
MEMORY CLEAR MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [HDMI IN] buttons,
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [HDMI IN] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “MEMORY CLEARING***” appears and the
memories are reset to the default values.
3. When done, the message “MEMORY CLEARED *” appears.
FACTORY PRESET MODE
The tuner preset are initialized.
Procedure:
1. While pressing the [TUNING MODE] and [2CH/A.DIRECT]
The tuner preset are initialized.
Procedure:
1. While pressing the [TUNING MODE] and [2CH/A.DIRECT]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “Factory Preset” appears and tuner preset are ini-
tialization is preformed.
TUNER AM STEP CHANGE MODE
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
ER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the [
?/1
]
button to turn on the main power.
5. Either the message “AM9k Step” or “AM10k Step” appears,
select the desired step.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. Initialize” appears and initialization is per-
formed.
FLUORESCENT INDICATOR TUBE DISPLAY TEST
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [HDMI IN] and [MOVIE/HD-D.C.S.] but-
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [HDMI IN] and [MOVIE/HD-D.C.S.] but-
tons, press the [
?/1
] button to turn on the main power.
2. All segments and all LEDs turn on.
3. Each time [DISPLAY] button to change as follows all on, test
3. Each time [DISPLAY] button to change as follows all on, test
pattern 1, test pattern 2, all off, all on in this order.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A. DI-
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A. DI-
RECT] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “SWAP MODE !” appears (No change while dis-
played).
SOUND FIELD LOCK ON/OFF CHANGE MODE
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [HDMI IN] and [MUSIC] buttons, press
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [HDMI IN] and [MUSIC] buttons, press
the [
?/1
] button to turn on the main power.
2. Either the message “SETTINGS LOCK [OFF]” or “SET-
TINGS LOCK [ ON]” appears.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the [
1. While pressing the [2CH/A. DIRECT] button, press the [
?/1
]
button to turn on the main power.
2. Either the message “COMMAND MODE [AV1]” or “COM-
MAND MODE [AV2]” appears. Select the desired mode.
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
The software version is displayed.
Note: In this mode, never press the [
M] and [m] buttons on the remote
commander.
Procedure:
1. While pressing the [2CH/A.DIRECT] and [HDMI IN] buttons,
1. While pressing the [2CH/A.DIRECT] and [HDMI IN] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “MAIN A56ES
∗∗∗ vX.XX” appears.
Each time the [DISPLAY] button is pressed, “SUB COMMON
C vX. XX”, “Video Ucom Ver X. XX”, “FAROUDJA Ver X.
XX”, “FAROUDJA2nd Ver X. XX”, “GUI CGROM Ver X.
XX”, “DSP Ucom Ver X. XX”, “DSP SFLASH Ver X.XX”
and “DSP PFLASH Ver X. XX” this order, and returns to the
“MAIN A56ES
C vX. XX”, “Video Ucom Ver X. XX”, “FAROUDJA Ver X.
XX”, “FAROUDJA2nd Ver X. XX”, “GUI CGROM Ver X.
XX”, “DSP Ucom Ver X. XX”, “DSP SFLASH Ver X.XX”
and “DSP PFLASH Ver X. XX” this order, and returns to the
“MAIN A56ES
∗∗∗ vX.XX” displayed.
SHIPMENT MODE
Initialize backup of EEPROM and Network and return to state of
the shipment.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [A.F.D.]
Initialize backup of EEPROM and Network and return to state of
the shipment.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [A.F.D.]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “MEMORY CLEARING***” appears and return
to state of the shipment.
3. When done, the message “STANDBY” appears and turn off
the main power.
REBOX TEST MODE
Displayed the number of times of the power on after the shipment.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [MUSIC]
Displayed the number of times of the power on after the shipment.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [MUSIC]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “REBOX- XX” appears.
KEY CHECK MODE
Button check.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [MOVIE/
Button check.
Procedure:
1. While pressing the [HDMI IN], [TONE MODE] and [MOVIE/
HD-D.C.S.] buttons, press the [
?/1
] button to turn on the main
power.
2. Either the message “REST 15” appears.
Every pressing of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
appears.
not counted again. When all buttons are pressed “REST 00”
appears.
STR-DA5600ES
23
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [MEMORY/ENTER] and [MUSIC] but-
The state that the set is used is memorized.
Procedure:
1. While pressing the [MEMORY/ENTER] and [MUSIC] but-
tons, press the [
?/1
] button to turn on the power and “HIS-
TORY” is displayed.
2. Each time the [
M] and [m] buttons of remote commander is
pressed, the item is switched in order as follows.
Items
Display
Protector generation total count
PRCT_COUNT: xxxx
Operating time until generating fi rst
time protector (active standby is
contained)
time protector (active standby is
contained)
TTL_TIME:xxxxH xxM
Main on time until generating fi rst
time protector
time protector
TTL_MAIN:xxxxH xxM
Factor of generating fi rst time protec-
tor
tor
PROTECT:xxxx
Sound fi eld in fi rst time protector
SF xxxx
Input selector in fi rst time protector
INPUT:xxxx
Input mode in fi rst time protector
INMODE:xxxx
Input under lock in fi rst time protector
DSEL:xxxx
Stream under input in fi rst time
protector
protector
STREAM:xxxx
Channel information in fi rst time
protector
protector
CONFIG:xxxx
State of headphone in fi rst time
protector
protector
HEADPHONE:xxxx
Volume in fi rst time protector
VOL:xxxx.xxdB
Muting in fi rst time protector
MUTING:xxxx
EQ setting value in fi rst time protector
FRT BASS:xxxx.xxdB
FRT TREB:xxxx.xxdB
FRT TREB:xxxx.xxdB
CNT BASS:xxxx.xxdB
CNT TREB:xxxx.xxdB
CNT TREB:xxxx.xxdB
SUR BASS:xxxx.xxdB
SUR TREB:xxxx.xxdB
SUR TREB:xxxx.xxdB
FH BASS:xxxx.xxdB
FH TREB:xxxx.xxdB
FH TREB:xxxx.xxdB
Level collection value each channel
in fi rst time protector
in fi rst time protector
Lv FL/FR:xx.xx/xx.xx
Lv CT/SW:xx.xx/xx.xx
Lv SL/SR:xx.xx/xx.xx
Lv BL/BR:xx.xx/xx.xx
Lv LF/RH:xx.xx/xx.xx
Lv BL/BR:xx.xx/xx.xx
Lv LF/RH:xx.xx/xx.xx
Total operation time after the ship-
ment
ment
TTL_P_ON:xxxxHxxM
Main zone power on time after the
shipment
shipment
TTL_M_ON:xxxxHxxM
Number of times of the power on
after the shipment
after the shipment
REBOX: xxxx
3. The backup data of the history mode are not initialized with
the “MEMORY CLEAR MODE”. Initialize it with a “SHIP
MODE”.
MODE”.
DMPORT TEST MODE
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN6701) on the NETWORK board.
2. While pressing the [HDMI IN] and [A.F.D.] buttons, press the
[
?/1
] button to turn on the main power.
3. The message “DMPORT OK”appears on the fl uorescent indi-
cator tube and enter the DMPORT test mode (Confi rmation of
communication line).
communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [
>] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [
.] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
x] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
NETWORK board
CN6701
MAIN board
TM4002
A VIDEO board
J6002
SIRIUS FACTORY TEST MODE
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [
?/1
] but-
ton to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the Module ver-
sion, SSP version, Security processor version, Audio processor
version, Firmware product ID, Firmware product sequence ID,
Sirius ID are displayed, next the output of the audio signal of
1 kHz L/R, 20 Hz L/R, 10 Hz L/R, noise L, noise R and stop
tone are switched.
version, Firmware product ID, Firmware product sequence ID,
Sirius ID are displayed, next the output of the audio signal of
1 kHz L/R, 20 Hz L/R, 10 Hz L/R, noise L, noise R and stop
tone are switched.
STR-DA5600ES
24
SPECIAL MENU MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT],
[MUSIC], [MOVIE/HD-D.C.S.] button in order, the message “MENU SPECIALIZED!” appears.
2. Press the [
M
]/[
m
] buttons of the remote commander, the message “<<< SPECIAL >>>” appears.
3. Press the [
,
] button of the remote commander, the item is appears.
4. Each time the [
M
]/[
m
] buttons of the remote commander is pressed, the item is switched in order as follows.
Some items can change the content. Display the cursor by pressing the [
,
] button of the remote commander, and changing the content
by pressing the [
M
]/[
m
] buttons of the remote commander, and fi x the content by pressing the [
<
] button of the remote commander
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE/HD-
D.C.S.] button in order again, the message “MENU SPECIALIZE OFF” appears.
Items
Display
Remark
SYSTEM version display
SYSTEM VERSION X.XXX
X.XXX: System software version
MAIN Ucom version display
MAIN A56ES
∗∗∗ vX. XX
∗∗∗: Destination
X.XX: Main system controller software version
X.XX: Main system controller software version
SUB Ucom version display
SUB COMMON C vX.XX
X.XX: Sub system controller software version
Video Ucom version display
Video Ucom Ver X. XX
X.XX: Video system controller software version
FAROUDJA version display
FAROUDJA Ver X. XX
X.XX: Video processor software version (main)
FAROUDJA (2nd) version display
FAROUDJA2nd Ver X.XX
X.XX: Video processor software version (2nd)
GUI CG-ROM version display
GUI CGROM Ver X. XX
X.XX: CG-ROM software version
DSP Ucom version display
DSP Ucom Ver X. XX
X.XX: DSP controller version
DSP serial fl ash version display
DSP SFLASH Ver X. XX
X.XX: DSP serial fl ash software version
DSP parallel fl ash version display
DSP PFLASH Ver X. XX
X.XX: DSP parallel fl ash version
IR learning Ucom version display
IR LEARNING Ver X. XX
X.XX: IR learning fi rmware version
Network processor version
NET 10A56COM Ver X. XX
X.XX: Network processor fi rmware version
DSP debug menu
< DSP DEBUG MENU >
Not used for the servicing
Network debug menu
< NETWORK DEBUG MENU >
Menu mode to enter MAC address display. If the [ENTER] but-
ton of the remote commander is pressed, entering the menu,
and operating the following menu become possible.
ton of the remote commander is pressed, entering the menu,
and operating the following menu become possible.
MAC address display
(Network debug menu)
(Network debug menu)
MACXX:XX:XX:XX:XX:XX
XX:XX:XX:XX:XX:XX: MAC address
Network update check
(Network debug menu)
(Network debug menu)
NET UPDATE CHECK?
If the [Enter] button of the remote commander is pressed, the
checking result is displayed without connecting to network.
“NET UPDATE CHK OK”: OK, “NET UPDATE CHK NG D”:
DSP Ucom NG, “NET UPDATE CHK NG F1”: Faroudja1 NG,
“NET UPDATE CHK NG F2”: Faroudja2 NG, “NET UPDATE
CHK NG V”: Video Ucom NG, “NET UPDATE CHK NG L”:
Learning Ucom NG, “NET UPDATE CHK NG M”: Main Ucom
NG, “NET UPDATE CHK NG S”: Sub Ucom NG
checking result is displayed without connecting to network.
“NET UPDATE CHK OK”: OK, “NET UPDATE CHK NG D”:
DSP Ucom NG, “NET UPDATE CHK NG F1”: Faroudja1 NG,
“NET UPDATE CHK NG F2”: Faroudja2 NG, “NET UPDATE
CHK NG V”: Video Ucom NG, “NET UPDATE CHK NG L”:
Learning Ucom NG, “NET UPDATE CHK NG M”: Main Ucom
NG, “NET UPDATE CHK NG S”: Sub Ucom NG
PNX JTAG Update mode (Network
debug menu)
debug menu)
JTAG UPDATE: XXX
XXX: ON or OFF
PNX polling and reset function
(Network debug menu)
(Network debug menu)
PNX POLL&RESET XXX
XXX: ON or OFF
Send a command regularly, and it is a function to reset when
there is not reaction.
Send a command regularly, and it is a function to reset when
there is not reaction.
DMS on/off (Network debug menu)
DMS(ZONE4) XXX
Not used for the servicing
ZONE4 power and input (Network
debug menu)
debug menu)
ZONE4:XXX INPUT:##
Not used for the servicing
DMR on/off (Network debug menu)
DMR XXX
XXX: ON or OFF
External control on/off (Network
debug menu)
debug menu)
EXTERNAL CTRL XXX
XXX: ON or OFF
Network standby on/off (Network
debug menu)
debug menu)
NETWORK STANDBY XXX
XXX: ON or OFF
Click on the first or last page to see other STR-DA5600ES service manuals if exist.