Sony STR-DA1800ES Service Manual ▷ View online
STR-DA1800ES
21
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
ER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [INPUT MODE] button, press the [
?/1
]
button to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
AM 9k Step
AM10k Step
or
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon comple-
tion of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon comple-
tion of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. Initialize” appears and initialization is per-
formed.
S.F. CLEAR
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [DISPLAY MODE]
The software version is displayed.
Procedure:
1. While pressing the [INPUT MODE] and [DISPLAY MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The model name/destination/system controller version ap-
pears. Each time the [DISPLAY MODE] button is pressed, the
version is switched in order as follows.
version is switched in order as follows.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
A1 UC M1.00
H.Ver 1.00
Model name/Destination/
System controller version
System controller version
Video controller version
S.Ver 1.00
DSP firmware version
F.Ver 1.00
Video system controller
version
version
N.Ver 1.00
Network firmware version
T.Ver 0.15
Tuner firmware version
Releasing method:
Press the [
Press the [
?/1
] button to turn off the main power.
HISTORY MODE
The state that the set is used is memorized.
The state that the set is used is memorized.
Note: Even if “USER INITIALIZE MODE” is performed, the backup
data of “HISTORY MODE” is not cleared.
Initialize by performing “SHIPMENT MODE”.
Procedure:
1. While pressing the [TONE MODE] and [MUSIC] buttons,
1. While pressing the [TONE MODE] and [MUSIC] buttons,
press the [
?/1
] button to turn on the power and “HISTORY” is
displayed.
HISTORY
2. Each time the [M] or [m] buttons of remote commander is
pressed, the item is switched in order as follows.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
COUNT XX
SxxxxxHxxM
Protector count
Total single power on time
SOUNDFIELD
Sound field
FUNCTION
Input function
INPUT MODE
Input mode
DIG SELECT
Digital select
Stream information
Signal configuration
Headphones
Volume
Bass
Treble
Level FL/FR
Level SL/SR
Level CT/SW
Level SBL/SBR
Level LH/RH
Total power on time
Muting
Power on counter
STREAMINFO
CONF xxxxx
HEADPH xxx
VOL xx
BASS xxxdB
TREB xxxdB
FL/Rxxxxxx
SL/Rxxxxxx
C/SWxxxxxx
BL/Rxxxxxx
HL/Rxxxxxx
T 1H25M
MUTING xxx
REBOX 11
Protector status
Temperature status
VACS step
PROT xxxx
TEMP xxxc
VACS xx
Releasing method:
Press the [
Press the [
?/1
] button to turn off the main power.
STR-DA1800ES
22
SHIPMENT MODE
Initialize backup of EEPROM and Network and return to state of
the shipment.
Procedure:
1. While pressing the [INPUT MODE] and [DIMMER] buttons,
Initialize backup of EEPROM and Network and return to state of
the shipment.
Procedure:
1. While pressing the [INPUT MODE] and [DIMMER] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” and “CLEARED !” appears and
return to state of the shipment.
CLEARING
CLEARED !
3. When done, the message “STANDBY” appears and turn off
the main power.
STANDBY
PROTECTOR AUTO OFF MODE
The auto off function after protection generating can be disabled.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
The auto off function after protection generating can be disabled.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “PROTEVER” appears and the auto off function
after protection generating is disabled.
PROTEVER
Releasing method:
Pull out the AC power cord.
Pull out the AC power cord.
USER INITIALIZE MODE
This unit can be returned to the factory default settings.
Procedure:
1. Hold down the [
This unit can be returned to the factory default settings.
Procedure:
1. Hold down the [
?/1
] button for over fi ve second to turn on the
main power.
2. The message “CLEARING” and “CLEARED !” appears and
this unit can be returned to the factory default settings.
CLEARING
CLEARED !
SETTING LOCK ON/OFF CHANGE MODE
All the settings can be locked.
Procedure:
1. While pressing the [SPEAKERS (A/B/A+B/OFF)] and [MU-
All the settings can be locked.
Procedure:
1. While pressing the [SPEAKERS (A/B/A+B/OFF)] and [MU-
SIC] buttons, press the [
?/1
] button to turn on the main power.
2. The message “S. LOCK ON” appears and the all settings is
locked.
S. LOCK ON
Releasing method:
1. While pressing the [SPEAKERS (A/B/A+B/OFF)] and [MU-
1. While pressing the [SPEAKERS (A/B/A+B/OFF)] and [MU-
SIC] buttons, press the [
?/1
] button to turn on the main power.
2. The message “S. LOCK OFF” appears and the all settings is
unlocked.
S. LOCK OFF
USB UPDATE MODE
This mode is guided by the technical news, when update occurs.
This mode is guided by the technical news, when update occurs.
USB UPDATE VERSION
This mode is guided by the technical news, when update occurs.
This mode is guided by the technical news, when update occurs.
SOFTWARE VERSION DISPLAY MODE (IN SPECIAL
MENU MODE)
The software version is displayed.
Procedure:
1. Press the [
MENU MODE)
The software version is displayed.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “SPECIALIZE” appears.
order, the message “SPECIALIZE” appears.
SPECIALIZE
3. Press the [AMP MENU] button of the remote commander, the
message “< SPECIAL >” appears.
< SPECIAL >
4. Press the [
,
] button of the remote commander, the item is
appears.
VERSION
5. Confi rm that the “VERSION” is displayed, and press the [
,
]
button of the remote commander.
6. The model name/destination/system controller version ap-
pears. Each time the [M]/[m] buttons are pressed, the version
is switched in order as follows.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
A1 UC M1.00
H.Ver 1.00
Model name/Destination/
System controller version
System controller version
Video controller version
S.Ver 1.00
DSP firmware version
F.Ver 1.00
Video system controller
version
version
N.Ver 1.00
Network firmware version
T.Ver 0.15
Tuner firmware version
Releasing method:
1. Press the [
1. Press the [
<
] button of the remote commander, the item is
appears.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “OFF” appears.
order, the message “OFF” appears.
OFF
STR-DA1800ES
23
AUTO CAL MIC TEST MODE (IN SPECIAL MENU
MODE)
MODE)
The auto calibration microphone input can be outputted from the speaker.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the main power.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “SPECIALIZE” appears.
order, the message “SPECIALIZE” appears.
SPECIALIZE
3. Press the [AMP MENU] button of the remote commander, the
message “< SPECIAL >” appears.
< SPECIAL >
4. Press the [
,
] button of the remote commander, the item is
appears.
VERSION
5. Press the [M]/[m] buttons to select the “SP OUT”, and press
the [
,
] button of the remote commander.
SP OUT
6. The output source from a speaker is displayed. Each time the
[M]/[m] buttons are pressed, the output source is switched as
follows.
SOURCE
MIC
Speaker output from
normal audio input
normal audio input
Speaker output from
auto calibration
microphone input
auto calibration
microphone input
Releasing method:
1. Press the [
1. Press the [
<
] button of the remote commander, the item is
appears.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “OFF” appears.
order, the message “OFF” appears.
OFF
FL FONT CHECK MODE (IN SPECIAL MENU MODE)
All the fonts which can be displayed can be checked.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the main power.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “SPECIALIZE” appears.
order, the message “SPECIALIZE” appears.
SPECIALIZE
3. Press the [AMP MENU] button of the remote commander, the
message “< SPECIAL >” appears.
< SPECIAL >
4. Press the [
,
] button of the remote commander, the item is
appears.
VERSION
5. Press the [M]/[m] buttons to select the “FL FONT”, and press
the [
,
] button of the remote commander.
FL FONT
6. The font is displayed. Each time the [M]/[m] buttons are
pressed, the font is switched.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
0x21 = !
Releasing method:
1. Press the [
1. Press the [
<
] button of the remote commander, the item is
appears.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “OFF” appears.
order, the message “OFF” appears.
OFF
STR-DA1800ES
24
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Adjustment to decide the standard of the video input signal.
Note: After replacing the D-VIDEO NW board, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
2. Preparation
In order to perform adjustment, you must perform the super reset
in special menu mode.
Refer to the following procedure.
Procedure:
1. Press the [
In order to perform adjustment, you must perform the super reset
in special menu mode.
Refer to the following procedure.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. While pressing the [TONE MODE] button, press the [A.F.D.],
[2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in
order, the message “SPECIALIZE” appears.
order, the message “SPECIALIZE” appears.
SPECIALIZE
3. Press the [AMP MENU] button of the remote commander, the
message “< SPECIAL >” appears.
< SPECIAL >
4. Press the [
,
] button of the remote commander, the item is
appears.
VERSION
5. Press the [M]/[m] buttons to select the “RESET”, and press the
[
,
] button of the remote commander.
RESET
6. Press the [M]/[m] buttons to select the “YES”, and press the
[ ] button of the remote commander.
YES
7. The message “ROM INIT” and “CLEAERD
” appears.
ROM INIT
CLEARED *
8. The super reset is completed.
SECTION 4
ELECTRICAL ADJUSTMENTS
3. Video calibration adjustment
3-1. Connection
3-1. Connection
color pattern
generator
or
Blu-ray
Disc player
STR-DA1800ES
TV
monitor
AVIDEO board
SAT/CATV VIDEO IN jack (J6002)
SAT/CATV VIDEO IN jack (J6002)
AVIDEO board
MONITOR VIDEO OUT jack (J6003) or
D-VIDEO NW board
HDMI OUT A ARC connector (CN3706)
MONITOR VIDEO OUT jack (J6003) or
D-VIDEO NW board
HDMI OUT A ARC connector (CN3706)
VIDEO cable or
HDMI cable
HDMI cable
3-2. Procedure for color pattern generator
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on the fl uorescent indicator tube.
Procedure:
1. It connects of step 3-1, and the turn on the main power.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on the fl uorescent indicator tube.
Procedure:
1. It connects of step 3-1, and the turn on the main power.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [
\/1
] button to turn off the main power.
5. While pressing the [MOVIE (HD-D.C.S.)] and [SPEAKERS
(OFF/A/B/A+B)] buttons, press the [
\/1
] button to turn on
the main power. When correctly entering the test mode “FIN
_:_:_” and “N:MWx_ _ _ _ _” are displayed in 1 second inter-
val (alternating display).
_:_:_” and “N:MWx_ _ _ _ _” are displayed in 1 second inter-
val (alternating display).
6. The NTSC signal adjustment is begun when press the [ ] but-
ton of the remote commander, and the display changes from
“N:MWx_ _ _ _ _” to “N:MWoCDV_ _” little by little. Fi-
nally, “FIN N:_:_” and “N: MWoCDV_ _” are displayed in 1
second interval (alternating display).
“N:MWx_ _ _ _ _” to “N:MWoCDV_ _” little by little. Fi-
nally, “FIN N:_:_” and “N: MWoCDV_ _” are displayed in 1
second interval (alternating display).
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
tern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. Turn off the main power.
11. Turn off the main power.
3-3. Procedure for Blu-ray Disc player
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on the fl uorescent indicator tube.
Procedure:
1. It connects of step 3-1, and the turn on the main power of set
Ensure GUI mode is turned off. Press GUI mode on remote until
GUI OFF is shown on the fl uorescent indicator tube.
Procedure:
1. It connects of step 3-1, and the turn on the main power of set
and Blu-ray Disc player.
2. “SAT/CATV” is selected by using [INPUT SELECTOR] dial.
3. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
3. Press the OPEN/CLOSE button of the Blu-ray Disc player, and
DVD test disc “HLX-504 (Part No. J-6090-088-A)” or “HLX-
513 (Part No. J-2501-305-A)” is insert. The disc playback au-
tomatically becomes start “Main Menu” is display.
513 (Part No. J-2501-305-A)” is insert. The disc playback au-
tomatically becomes start “Main Menu” is display.
4. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
5. Press the [
\/1
] button to turn off the main power.
6. While pressing the [MOVIE (HD-D.C.S.)] and [SPEAKERS
(OFF/A/B/A+B)] buttons, press the [
\/1
] button to turn on
the main power. When correctly entering the test mode “FIN
_:_:_” and “N:MWx_ _ _ _ _” are displayed in 1 second inter-
val (alternating display).
_:_:_” and “N:MWx_ _ _ _ _” are displayed in 1 second inter-
val (alternating display).
7. The NTSC signal adjustment is begun when press the [ ] but-
ton of the remote commander, and the display changes from
“N:MWx_ _ _ _ _” to “N:MWoCDV_ _” little by little. Fi-
nally, “FIN N:_:_” and “N: MWoCDV_ _” are displayed in 1
second interval (alternating display).
“N:MWx_ _ _ _ _” to “N:MWoCDV_ _” little by little. Fi-
nally, “FIN N:_:_” and “N: MWoCDV_ _” are displayed in 1
second interval (alternating display).
Click on the first or last page to see other STR-DA1800ES service manuals if exist.