Sony STR-DA1800ES Service Manual ▷ View online
STR-DA1800ES
13
2-6. STANDBY BOARD
L
7
two screws
(BVTP3
u 8)
8
STANDBY baord
7
two screws
(BVTP3
u 8)
1
connector
(CNP902)
5
connector
(CN906)
6
connector
(CN908)
3
AC inlet 2P connector
(CNP901)
4
Cut the cable tie.
2
Cut the binding band (taiton).
L
cable tie
front side
rear side
power transformer
(T901)
(T901)
STANDBY baord
AC inlet 2P (AC1)
clamp filter
(ferrite core)
(FC2)
(ferrite core)
(FC2)
:LUHsetting
Note: In reassembling, use new cable tie or new binding
band (taiton) to fasten the clamp same as before.
cable tie
power transformer
(T901)
(T901)
STANDBY baord
DCDC2 baord
heat sink
:iUesetting
rear side
front side
STR-DA1800ES
14
2-7. DCDC BOARD, DCDC2 BOARD
6
two screws
(BVTP3
u 8)
7
DCDC2 board
3
connector
4
Cut the cable tie.
5
clamp filter (ferrite core)
(FC1)
Note: In reassembling, use new cable tie
to fasten the clamp same as before.
1
Cut thecable tie.
:LUHsetting
clamp filter
(ferrite core)
(FC1)
(ferrite core)
(FC1)
DCDC2 board
front side
rear side
M
M
2
Remove wire from
the lead pin.
:iUesetting
lead pin
cable tie
AVIDEO board
rear side
9
screw
(BVTP3
u 8)
9
screw
(BVTP3
u 8)
0
DCDC board
DCDC2 board
8
connector
(CN1500)
cable tie
AVIDEO board
rear side
Through the first fin of J6006.
STR-DA1800ES
15
2-9. TUNER1AMF ASSY (TU1)
2-8. HAT BOARD
4
screw
(BVTP3
u 8)
3
two screws
(supplied with J861)
5
HAT board
2
wire (flat type) (11 core)
(CN811)
1
Remove wire from
the lead pin.
Note: When installing the wire (flat type),
ensure the colored line.
No slanting after insertion.
wire (flat type)
wire (flat type)
colored line
colored line
Insert is straight to the interior.
Insert is incline
connector
connector
OK
NG
:LUHsetting
TUNER1AMF assy
(TU1)
HAT board
lead pin
3
two screws
(BVTP3
u 8)
4
TUNER1AMF assy
(TU1)
1
Remove wire from
the lead pin.
:LUHsetting
TUNER1AMF assy
(TU1)
HAT board
lead pin
Note: When installing the wire (flat type),
ensure the colored line.
No slanting after insertion.
2
wire (flat type)
(9
core)
wire (flat type)
wire (flat type)
colored line
colored line
Insert is straight to the interior.
Insert is incline
connector
connector
OK
NG
STR-DA1800ES
16
2-11. CENTER BRACKET BLOCK
2-10. BACK PANEL BLOCK
2
four screws
(BVTP3
u 8)
2
two screws
(BVTP3
u 8)
2
five screws
(BVTP3
u 8)
2
six screws
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
3
back panel block
1
four screws
(BV/ring)
Roll the wire once.
140 ± 5 mm
AC inlet 2P (AC1)
clamp filter (ferrite core)
(FC2)
(FC2)
&ODPSILOWHUIHUULWHFRUH)&
2
screw
(BVTP3
u 8)
1
screw
(BVSP4
u 8)
3
center bracket block
Click on the first or last page to see other STR-DA1800ES service manuals if exist.