Sony SRS-X88 Service Manual ▷ View online
SRS-X88
21
2-16. HEAT SINK (UPPER)
:LUHVHWWLQJ
1 screw
(BTTP
(BTTP
M2.6
u 8)
1 two screws
(BTTP
(BTTP
M2.6
u 8)
2 two screws
(BVTT2.6
(BVTT2.6
u 4)
2 two screws
(BVTT2.6
(BVTT2.6
u 4)
3 heat sink (upper)
heat sink (upper)
clamp filter (ferrite core)
(FC2)
(FC2)
clamp filter
(ferrite core)
(FC3)
(ferrite core)
(FC3)
sleeve ferrite clamp
(FC1)
(FC1)
Note 2: Confirm that the connector (CN007)
of the MAIN board is visible.
Note 1: The wire must not touch
the heat sink (upper).
SRS-X88
22
2-17. CARD WLAN/BT COMBO
1 tape
(sub
(sub
material)
tape
(sub material)
(sub material)
tape
(sub material)
(sub material)
1 tape
(sub
(sub
material)
5 antenna
connector
(CON4)
connector
(CON4)
4 card WLAN/BT combo
connector
connector
card WLAN/BT combo
card WLAN/BT
combo
combo
card WLAN/BT
combo
combo
$QWHQQDZLUHVHWWLQJ
:LUHVHWWLQJ
3 Remove the card WLAN/BT combo
block in the direction of the arrow.
A
A
2 screw
(BTTP
(BTTP
M2.6
u 8)
6 screw
(BVTT2.6
(BVTT2.6
u 4)
7 holder (WI-FI)
8 two sheets (1)
sheet (1)
sheet (1)
guide line
guide line
9 card WLAN/BT combo
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
20 mm
sleeve ferrite
clamp (FC1)
clamp (FC1)
heat sink (lower)
guide line
card WLAN/BT
combo
combo
Note 3: When affixing the tape, be careful
that it does not obstruct the hole.
Note 4: The antenna wire must not
touch the shield portion.
antenna wire
3DVWLQJSRVLWLRQRIWKHVKHHW
Note 1: Be sure to replace the complete NETWORK board and card WLAN/
BT combo at the same time. Be sure to also follow “NOTE OF RE-
PLACING THE COMPLETE NETWORK BOARD AND CARD
WLAN/BT COMBO” on page 3 during replacement.
PLACING THE COMPLETE NETWORK BOARD AND CARD
WLAN/BT COMBO” on page 3 during replacement.
Note 2: When replacing the card WLAN/BT combo, refer to “CHECKING
OF NETWORK CONNECTION” on page 3.
SRS-X88
23
2-18. JACK BOARD
Note 1: Lay a soft piece of cloth
under the unit to avoid
damaging the top panel.
2 two screws
(BTTP
(BTTP
M2.6
u 8)
2 screw
(BTTP
(BTTP
M2.6
u 8)
2 screw
(BTTP
(BTTP
M2.6
u 8)
5 Cut the binding band (taiton).
6 MAIN board
CN404
CN404
cable
connector
4pin
(CN1507)
4 MAIN board CN508
cable connector 4pin
(CN1508)
8 MAIN board CN403 cable
connector
connector
6pin
(CN1503)
9 MAIN board CN103 cable
connector 11pin (CN1506)
7 MAIN board
CN100
CN100
cable
connector
3pin
(CN1504)
3pin
(CN1504)
0 MAIN board CN101
cable connector 3pin
(CN1505)
A
A
B
C
B
C
qa four sheets (1)
qs JACK board
JACK board
1 screw
(B3
(B3
u 6)
3 Lift up the JACK board block
in the direction of the arrow.
Note 2: During reassembly, use new binding
band (taiton) to fasten the wires back
in place as they were before
disassembly.
binding band (taiton)
guide line
:LUHVHWWLQJ
:LUHVHWWLQJ
5 mm
NG
0.5 mm
0.5 mm
0.5 mm
0.5 mm
0.5 mm
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
–5HDUERWWRPYLHZ–
3DVWLQJSRVLWLRQRIWKHVKHHW
CN1501
J1503
screw hole
(hexagon support (15))
(hexagon support (15))
Note 3: Pull the wires in the direction
of the arrow so that the screw
hole is not obstruct.
wire
The wires are twisted.
Note 5: Install the JACK board while
bending the wires into an
S
shape.
Note 4: Bend the wires at 5 mm
position from the connector.
SRS-X88
24
2-19. MAIN BOARD BLOCK-1
•
Continued on 2-20 (page 25).
OK
NG
NG
:LUHVHWWLQJ
Note 2: Lay a soft piece of cloth
under the unit to avoid
damaging the top panel.
3 two screws
(BTTP
(BTTP
M2.6
u 8)
5 two screws
(BTTP
(BTTP
M2.6
u 8)
4 plate (wire POW) block
6 plate (wire jack)
7 wedge rubber
OK
NG
:LUHVHWWLQJ
3 mm
3 mm or less.
OK
NG
NG
NG
–5HDUERWWRPYLHZ–
1 screw
(P4
(P4
u 6)
2 ring (screw)
+RZWRLQVWDOOWKHZHGJHUXEEHU
More than 3 mm.
wedge rubber
wedge rubber
More than
3 mm.
3 mm.
wedge rubber
More than 3 mm.
wedge rubber
There is not a gap.
gap
There is a gap.
2 to 3 mm
2 mm or less.
More than 3 mm.
Note 1: For reference, only the 11 pin wire is indicated in the figures.
Click on the first or last page to see other SRS-X88 service manuals if exist.