Sony SRS-X88 Service Manual ▷ View online
SRS-X88
13
2-6. SPEAKER WIRE (L-ch)
OK
NG
– Baffle block bottom rear view –
2 Cut the binding band (taiton).
3 Remove the wires
from the clamp.
6 speaker wire (L-ch)
5 tweeter terminal (L-ch)
(wide) [brown] and [blue]
(See Note 2)
5 tweeter terminal (L-ch)
(narrow) [black] and [black]
(See Note 2)
4 midrange terminal (L-ch)
(narrow) [black] and [black]
(See Note 2)
4 midrange terminal (L-ch)
(wide) [blue] and [yellow]
(See Note 2)
:ire VettiQJ
binding band
(taiton)
(taiton)
Push the protrusion, and remove
the terminal (wide side).
the terminal (wide side).
Push the protrusion, and remove
the terminal (narrow side).
the terminal (narrow side).
protrusion
protrusion
curved crease
Curved crease is
below side.
below side.
protrusion
Note 2: When remove the terminal,
push the protrusion.
Note 1: During reassembly, use new binding band (taiton) to fasten
the wires back in place as they were before disassembly.
midrange
terminal
(L-ch)
terminal
(L-ch)
tweeter terminal
(L-ch)
(L-ch)
,QVtallatioQ GirectioQ for tKe termiQal
:ire VettiQJ
clamp
speaker wire
(L-ch)
(L-ch)
bottom side
to
CN501
1 filament tape
(sub
(sub
material)
:ire VettiQJ
filament tape
(sub material)
(sub material)
box
(LCH)
(LCH)
guide line
center
SRS-X88
14
2-7. RC/LED BOARD BLOCK, WINDOW (IR)
OK
NG
1 tapping screw
(P2
u 6)
RC board
hole
hole
3 two tapping screws
(P2
u 6)
6 window (IR)
5 O ring (IR)
– Baffle block top rear view –
window (IR)
boss
boss
O ring (IR)
Insert is fully straight.
window (IR)
O ring (IR)
Insert at a slant.
1 two tapping screws
(P2
u 6)
4 Remove the window (IR) block
in the direction of the arrow.
+RZWRLQVWDOOWKH2ULQJ,5
– Side view –
– Side view –
2 RC/LED board block
top side
LED board
Note: When installing the LED board,
Note: When installing the LED board,
align the two bosses and two holes.
SRS-X88
15
2-8. RC BOARD
2-9. LED BOARD
1 sheet (1)
1 sheet (1)
3 RC board
2 Remove the solder.
[black]
[black]
2 Remove the solder.
[red]
[red]
2 Remove the solder.
[white]
[white]
– Right view –
– Left view –
RC board
guide line
guide line
RC board
sheet (1)
sheet (1)
RC board
LED board
[white]
[black]
[red]
:LUHVHWWLQJ
3DVWLQJSRVLWLRQRIWKHVKHHW
guide line
guide line
RC board
:LUHVHWWLQJ
2 LED board
1 Remove the solder.
[black]
[black]
1 Remove the solder.
[white]
[white]
LED board
[black]
[white]
SRS-X88
16
2-10. BOX (LCH, RCH) BLOCK, O RING (LED)
OK
NG
Insert is fully straight.
indicator
Insert at a slant.
1 two tapping screws
(BTTP
(BTTP
M2.6
u 8)
1 two tapping screws
(BTTP
(BTTP
M2.6
u 8)
1 two tapping screws
(BTTP
(BTTP
M2.6
u 8)
1 two tapping screws
(BTTP
(BTTP
M2.6
u 8)
– Baffle block top rear view –
2 box (LCH) block
3 O ring (LED)
boss
hole
O ring (LED)
O ring (LED)
+RZWRLQVWDOOWKH2ULQJ/('
2 box (RCH) block
Note: When installing the box (RCH) block,
Note: When installing the box (RCH) block,
align the boss and hole.
indicator
O ring (LED)
indicator
top side
Click on the first or last page to see other SRS-X88 service manuals if exist.