Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual ▷ View online
41
SA-WSLF10/SS-CSL10/TSL10/TSL11
MAIN BOARD IC526
µ
PD703033BYGF-M68-3BA-A (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
DAMP_DATA
O
Serial data output to the HCD-LF10
2
2PIN
-
Not used
3
DIR/ADC_2
O
Selection signal output terminal
4
DIAT_DO
O
Serial data output to the RF modulator
5
DIAT_CLK
O
Serial data transfer clock signal output to the RF modulator
6
DSP_DO
I
Serial data input from the audio DSP
7
DIG_DI
O
Serial data output to the digital audio interface receiver and audio DSP
8
DIG_CLK
O
Serial data transfer clock signal output to the digital audio interface receiver and audio DSP
9
EVDD
-
Power supply terminal (+5V)
10
EVSS
-
Ground terminal
11
P_PWM
O
Voltage control signal output to the switching regulator
12
DSP_RESET
O
Reset signal output to the audio DSP "L": reset
13
DSP_PM
O
PLL initialize signal output to the audio DSP
14
DSP_CS
O
Chip select signal output to the audio DSP
15
DSP_HACN
I
Acknowledge signal input from the audio DSP
16
DSP_BST
O
Boot strap signal output to the audio DSP
17
DSP_GP9
I
Read ready signal input from the system controller
18
DIR_ZERO
I
Audio serial data input from the digital audio interface receiver
19
DIR_ERR
I
PLL lock error and data error flag input from the digital audio interface receiver
20
DIR_CE
O
Chip enable signal output to the digital audio interface receiver
21
VPP
-
Not used
22
DIR_XSTAT
I
Source clock switching monitor input from the digital audio interface receiver
23
DIR_ANADIG
O
Selection signal output terminal
24
DIR-XMODE
O
Reset signal output to the digital audio interface receiver "L": reset
25
DIR_DO
I
Serial data input from the digital audio interface receiver
26
DAMP_RST
O
Reset signal output to the stream processor "L": reset
27
DAMP_SKIP_PP
-
Not used
28
DAMP_MUTS
O
Soft muting on/off control signal output to the stream processor "H": muting on
29
DAMP_CS1
O
Chip select signal output to the stream processor (for front L-ch and R-ch)
30
DAMP_CS2
O
Chip select signal output terminal Not used
31
DAMP_CS3
O
Chip select signal output to the stream processor (for center and sub woofer)
32
DAC_CS
O
Chip select signal output terminal Not used
33
AD_RST
O
Reset signal output terminal Not used
34
RESET
I
System reset signal input from the HCD-LF10 "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
35
XT1
I
Sub system clock input terminal Not used
36
XT2
O
Sub system clock output terminal Not used
37
REGO
-
Not used
38
X2
O
Main system clock output terminal (20 MHz)
39
X1
I
Main system clock input terminal (20 MHz)
40
VSS
-
Ground terminal
41
VDD
-
Power supply terminal (+5V)
42
CLKOUT
O
Clock signal output terminal Not used
43
DRIVE_RST
O
Reset signal output to the power driver "L": reset
44
DIP_OCP
I
Protect signal input from the power driver
45
NO_USE
-
Not used
42
SA-WSLF10/SS-CTL10/TSL10/TSL11
Pin No.
Pin Name
I/O
Description
46
AU_MUTE
O
Audio muting on/off control signal output terminal Not used
47, 48
AV_SEL0,
AV_SEL1
O
Audio input selection signal output terminal
49
AV_SEL2
O
Audio input selection signal output terminal Not used
50
AV_SEL3
O
Video input selection signal output terminal
51
TUNED
I
Tuning detection signal input from the tuner unit "L": tuned
52
TUN_DI
I
Serial data input from the tuner unit
53
TUN_CE
O
Chip enable signal output to the tuner unit
54
TUN_DO
O
Serial data output to the tuner unit
55
TUN_CLK
O
Serial data transfer clock signal output to the tuner unit
56
TU_STEREO
I
FM stereo detection signal input from the tuner unit "L": stereo
57
TU_MUTE
O
Muting request control signal output to the tuner unit
58
BVDD
-
Power supply terminal (+5V) (for bus interface)
59
BVSS
-
Ground terminal (for bus interface)
60
DAMP_HP_MUTE
O
Headphone muting on/off control signal output "H": muting on
61
AV_SEL4
O
Video input selection signal output terminal
62
VS/WIDE
O
Wide control signal output to the video amplifier
63
I/P_SEL
O
Interlace/progressive selection signal output to the video amplifier
"L": interlace, "H": progressive
"L": interlace, "H": progressive
64
NO_USE
-
Not used
65
HP_SW
I
Headphone detection signal input terminal "H": headphone is connected
66
ADC_PDOWN
O
Power down signal output to the A/D converter
67
NO_USE
-
Not used
68
VOUT_ENE
O
Not used
69
YC-MIX
O
Y/chroma mix signal control signal output to the video amplifier
70
DVD_SEL
O
Not used
71
IP_SW
I
SCAN SELECT switch input terminal "L": selectable, "H": interlace
72
AV_SEL5
O
Video input selection signal output terminal
73
RGB_SEL
O
Not used
74
AVDD
-
Power supply terminal (+5V) (analog system)
75
AVSS
-
Ground terminal (analog system)
76
AVREF
I
Reference voltage (+5V) input terminal (analog system)
77 to 79
NO_USE
-
Not used
80
AREA
I
Destination setting terminal Not used
81 to 84
NO_USE
-
Not used
85
OVERFLOW_1
I
Overflow status signal input from the stream processor (for front L-ch and R-ch)
86
OVERFLOW_2
I
Overflow status signal input from the stream processor (for center and sub woofer)
87
NO_USE
-
Not used
88
RDS-DATA
I
RDS serial data input terminal Not used
89
IF_POWER
O
Not used
90
STOP_IN
I
System stop signal input from the HCD-LF10
91
UNMUTE
O
Muting control signal output terminal
92, 93
NO_USE
-
Not used
94
RDS_CLK
I
RDS serial data transfer clock signal input terminal Not used
95
DIAT_CSOD
I
Captor start delay signal input from the RF modulator
96
DIAT_CS
O
Chip select signal output to the RF modulator
97
DIAT_XRST
O
Reset signal output to the RF modulator "L": reset
98
DAMP_DATA
O
Serial data output to the stream processor
43
SA-WSLF10/SS-CSL10/TSL10/TSL11
Pin No.
Pin Name
I/O
Description
99
DAMPCLK
O
Serial data transfer clock signal output to the stream processor
100
IF_DATA_IN
I
Serial data input from the HCD-LF10
44
SA-WSLF10/SS-CTL10/TSL10/TSL11
SECTION 6
EXPLODED VIEWS
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
2-108-334-11 FOOT (AMP BOX)
2
X-2050-983-1 ASSY, PANEL (R) U (US)
2
X-2050-986-1 ASSY, PANEL (R) (SP, TW, AUS)
3
X-2050-981-1 ASSY, PANEL (F) U (US)
3
X-2050-984-1 ASSY, PANEL (F) (SP, TW, AUS)
4
X-2050-982-1 ASSY, PANEL (L) U (US)
4
X-2050-985-1 ASSY, PANEL (L) (SP, TW, AUS)
5
2-102-667-01 BASE
6
4-229-966-12 SCREW (4X16), +BV TAPPING
7
4-238-407-02 SCREW (1) (4X20), +BV TAPPING
8
A-1066-000-A SPEAKER CABINET ASSY (TW, AUS)
8
A-1105-799-A SPEAKER CABINET ASSY (US, SP)
SP901
1-825-965-11 SPEAKER (18cm)
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
6-1.
OVERALL SECTION (SA-WSLF10)
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
•
The mechanical parts with no reference
number in the exploded views are not supplied.
number in the exploded views are not supplied.
NOTE:
•
-XX and -X mean standardized parts, so they
may have some difference from the original
one.
may have some difference from the original
one.
•
Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color
Cabinet's Color
•
Abbreviation
AUS : Australian model
SP
AUS : Australian model
SP
: Singapore model
TW : Taiwan model
1
5
2
6
6
3
7
7
4
8
not supplied
not supplied
not supplied
not supplied
SP901
AMP assy section
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Click on the first or last page to see other SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 service manuals if exist.