DOWNLOAD Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual ↓ Size: 6.74 MB | Pages: 60 in PDF or view online for FREE

Model
SA-WSLF10 SS-CTL10 SS-TSL10 SS-TSL11
Pages
60
Size
6.74 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
sa-wslf10-ss-ctl10-ss-tsl10-ss-tsl11.pdf
Date

Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual ▷ View online

SERVICE MANUAL
SPEAKER SYSTEM
US Model
E Model
Australian Model
SA-WSLF10/
SS-CTL10/TSL10/TSL11
Ver. 1.1  2006.08
SPECIFICATIONS
9-879-563-02
2006H05-1
© 2006.08
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
– Continued on next page –
SA-WSLF10 is the subwoofer in DAV-LF10.
SS-CTL10 is the center speaker in DAV-LF10.
SS-TSL10 is the front speaker in DAV-LF10.
SS-TSL11 is the surround speaker in DAV-LF10.
This system incorporates with Dolby* Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS** Digital Surround
System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of
Dolby Laboratories.
**Manufactured under license from Digital Theater Systems, Inc.
“DTS”, “DTS-ES”, and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc.
Tuner section SA-WSLF10
System
PLL quartz-locked digital 
synthesizer system
FM tuner section
Tuning range
North American models:
87.5 – 108.0 MHz 
(100 kHz step)
Other models:
87.5 – 108.0 MHz
(50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
North American models:
530 – 1,710 kHz (with the 
interval set at 10 kHz)
531 – 1,710 kHz (with the 
interval set at 9 kHz)
Other models:
530 – 1,710 kHz (with the 
interval set at 10 kHz)
531 – 1,602 kHz (with the 
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section SA-WSLF10
Outputs
Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p 
75 ohms
Inputs
Video: 1 Vp-p 75 ohms
Speakers
Fro
For the US model
nt SS-TSL10
Speaker system
Two-way bass reflex, 
magnetically shielded
Speaker unit
50 mm (2 inches) dia. cone 
type 
×
 2, 25 mm (1 inch) 
dia. balance-dome-type 
tweeter
Rated impedance
4 ohms
Dimensions (approx.)
68 
×
380 
×
 53 mm (2 
3
/
4
 
×
 
15 
×
 2 
1
/
8
 inches) (w/h/d)
220 
×
 (398 – 530) 
×
 220 
mm (8 
3
/
4
 
×
 (15 
3
/
4
 – 20 
7
/
8
×
 8 
3
/
4
 inches) (w/h/d) with 
stand
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND 
TOTAL HARMONIC 
DISTORTION:
With 4 ohm loads, both 
channels driven, from 
200 – 20,000 Hz; rated
65 watts per channel 
minimum RMS power, 
with no more than 0.7 % 
total harmonic distortion 
from 250 milli watts to 
rated output.
Amplifier section SA-WSLF10
Stereo mode (rated)
86 W + 86 W (4 ohms at 
1 kHz, THD 10 %)
Surround mode (reference) music power output
Front: 
86 W (each)
(with SS-TSL10)
Center*: 
86 W
(with SS-CTL10)
Surround*: 
86 W
(with SS-TSL11)
Subwoofer*: 
85 W 
×
 2 
(with SA-WSLF10)
* Depending on the sound field settings and the source, 
there may be no sound output.
Inputs
VIDEO/SAT:
Sensitivity: 300 mV
Impedance: 50 kilohms
Phones
Accepts low-and high-
impedance headphones.
SA-WSLF10
SS-CTL10
SS-TSL10 SS-TSL11 STAND ASSY
2
SA-WSLF10/SS-CTL10/TSL10/TSL11
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK 
 0
  OR  DOTTED  LINE
WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
Mass (approx.)
1.3 kg (2 lb 14 oz)
2.7 kg (6 lb) with stand
Center SS-CTL10
Speaker system
Two-way bass reflex, 
magnetically shielded
Speaker unit
50 mm (2 inches) dia. cone 
type 
×
2, 25 mm (1 inch) 
dia. balance-dome-type 
tweeter
Rated impedance
4 ohms
Dimensions (approx.)
68 
×
 380 
×
 53 mm (2 
3
/
4
 
×
 
15 
×
 2 
1
/
8
 inches) (w/h/d)
Mass (approx.)
1.3 kg (2 lb 14 oz)
Surround SS-TSL11
Speaker system
Two-way bass reflex, 
magnetically shielded
Speaker unit
50 mm (2 inches) dia. cone 
type 
×
2, 25 mm (1 inch) 
dia. balance-dome-type 
tweeter
Rated impedance
4 ohms
Dimensions (approx.)
68 
×
 240 
×
 53 mm (2 
3
/
4
 
×
 
1
/
2
 
×
 2 
1
/
8
 inches) (w/h/d)
Mass (approx.)
1.0 kg (2 lb 4 oz)
Subwoofer SA-WSLF10
Speaker system
Bass reflex
Speaker unit
180 mm (7 
1
/
8
 inches) dia. 
cone type
Rated impedance
4 ohms 
×
 2
Dimensions (approx.)
241 
×
 606 
×
 241 mm 
(9 
1
/
2
 
×
 23 
7
/
8
 
×
 9 
1
/
2
 
inches) (w/h/d)
Mass (approx.)
14 kg (30 lb 14 oz)
Power requirements
North American models:
120 V AC, 60 Hz
Taiwan model:
120 V AC, 50/60 Hz
Other models:
220-240 V AC, 50/60 Hz
Power consumption
120 W
0.3 W (at the Power Saving 
mode) 
Design and specifications are subject to change 
without notice.
Notes on chip component replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable.  (See
Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15 
µ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
3
SA-WSLF10/SS-CTL10/TSL10/TSL11
TABLE  OF  CONTENTS
1.
SERVICING  NOTES
...............................................
3
2.
GENERAL
...................................................................
6
3.
DISASSEMBLY
.........................................................
7
4.
ELECTRICAL  ADJUSTMENT
............................
8
5.
DIAGRAMS
5-1.
Block Diagram – AUDIO DSP Section – ........................
9
5-2.
Block Diagram – AUDIO Section – ................................ 10
5-3.
Block Diagram
– VIDEO/POWER SUPPLY Section – ........................... 11
5-4.
Printed Wiring Board
– MAIN Board (Component Side) – ............................... 14
5-5.
Printed Wiring Board
– MAIN Board (Conductor Side) – ................................. 15
5-6.
Schematic Diagram – MAIN Board (1/4) – .................... 16
5-7.
Schematic Diagram – MAIN Board (2/4) – .................... 17
5-8.
Schematic Diagram – MAIN Board (3/4) – .................... 18
5-9.
Schematic Diagram – MAIN Board (4/4) – .................... 19
5-10. Printed Wiring Board
– S-MASTER Board (Component Side) – ...................... 20
5-11. Printed Wiring Board
– S-MASTER Board (Conductor Side) – ........................ 21
5-12. Schematic Diagram – S-MASTER Board (1/4) – ........... 22
5-13. Schematic Diagram – S-MASTER Board (2/4) – ........... 23
5-14. Schematic Diagram – S-MASTER Board (3/4) – ........... 24
5-15. Schematic Diagram – S-MASTER Board (4/4) – ........... 25
5-16. Printed Wiring Board – TX Board – ................................ 26
5-17. Schematic Diagram – TX Board – .................................. 27
5-18. Printed Wiring Board – VIDEO I/O Board – .................. 28
5-19. Schematic Diagram – VIDEO I/O Board – ..................... 29
5-20. Printed Wiring Boards
– COMPONENT/SPK-OUT Boards – ............................ 30
5-21. Schematic Diagram
– COMPONENT/SPK-OUT Boards – ............................ 31
5-22. Printed Wiring Boards – POWER SUPPLY Section – .... 32
5-23. Schematic Diagram – POWER SUPPLY Section – ........ 33
6.
EXPLODED  VIEWS
6-1.
Overall Section (SA-WSLF10) ....................................... 44
6-2.
AMP Assy Section (SA-WSLF10) .................................. 45
6-3.
MAIN Board Section (SA-WSLF10) .............................. 46
6-4.
SS-CTL10/TSL10/TSL11 Section .................................. 47
6-5.
Stand Section ................................................................... 48
7.
ELECTRICAL  PARTS  LIST
................................ 49
SECTION  1
SERVICING  NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 ˚C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MODEL  IDENTIFICATION
MODEL
PART No.
US model
2-590-864-0[]
Taiwan model
2-590-866-0[]
Singapore model
2-590-867-0[]
Australian model
2-591-603-0[]
Part No.
– Rear View –
4
SA-WSLF10/SS-CTL10/TSL10/TSL11
THE  CHECK  METHOD  OF  THE  OUTPUT  SIGNAL  FROM  TX  BOARD
Procedure:
1. A spectrum analyzer is connected to pin 1 and pin 2 of the output connector (CN803) of TX board.
2. Confirm that it is spectrum as shown in a figure with the spectrum analyzer. It is normal if the signal of a 3MHz to 6MHz zone (a center
is 4.5MHz) can be checked.
digital 
voltmeter 
10 
 (0.5%)
TX board
CN803 pin 
1
pin 
2
3. When the output signal from TX board is normal, pin 8 (SDATA), pin 4 (LRCKO) and pin 5 (BCKO) of the input signal connector
(CN801) are investigated.
Super audio CD/
DVD player :
HCD-LF10
Units required for
operation
check
Super audio CD/
DVD player : HCD-LF10
Sub woofer : 
SA-WSLF10
Front speaker : 
SS-TSL10
Center speaker : 
SS-CTL10
Surround speaker : 
SS-TSL11
Remote commander : 
RM-SP320
Unit. 
need to 
checking
a
a
a
Center 
speaker :
SS-CTL10
a
a
Sub woofer :
SA-WSLF10
a
a
a
a
Remote 
commander :
RM-SP320
IR transmitter :
DIR-T1
Remote
sensor :
DIR-R4
Surround 
amplifier :
TA-SB500WR
IR receiver :
DIR-R1
a
a
a
a
a
a
a
a
a
a
a
a
Surround 
speaker :
SS-TSL11
a*
1
Front speaker :
SS-TSL10
a*
1
a*
2
*
1  Only the defective unit.  
*
2  Either one of them.
Units with 
a
 mark: The units that are required for the system operation check during repair service
However, there can be a case that some units of the system need to not be brought into repair shop depending on the unit. that became defective. 
• The units that are required for the system operation check during repair service
Page of 60
Display

Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual ▷ Download

  • DOWNLOAD Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual ↓ Size: 6.74 MB | Pages: 60 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 in PDF for free, which will help you to disassemble, recover, fix and repair Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Audio. Information contained in Sony SA-WSLF10 / SS-CTL10 / SS-TSL10 / SS-TSL11 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.