Sony SA-WGT5D Service Manual ▷ View online
SA-WGT5D
37
2-29. FRONT PANEL BLOCK
7
Remove the front panel block
in the direction of the arrow.
1
LED board cable
connector
(CN901)
(CN901)
2
connector
(CN103)
–
Rear top view
–
3
flexible flat cable
(10P)
(FFC6)
(CN108)
terminal
face
face
ARAGON-MOTHER board
Wire setting
bluetooth module
(BT1)
(BT1)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
How to install the connector
Insert the connector straight into the interior.
There is a possibility that using this unit
without the connector correctly installed will
damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit
without the connector correctly installed will
damage it.
colored line
Insert straight into
the interior.
the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
4
two flat tapping
screws
total sixteen bosses
6
All bosses are removed
while moving jig in the
direction of the arrow,
and front panel block is
removed.
6
All bosses are removed
while moving jig in the
direction of the arrow,
and front panel block is
removed.
5
Insert the jig into a space and raise
front panel block.
Note: When using a jig, please work so
as not to injure front panel and
speaker
cabinet.
5
Insert the jig into a space and raise
front panel block.
Note: When using a jig, please work so
as not to injure front panel and
speaker
cabinet.
8
front panel block
Ver. 1.1
SA-WGT5D
38
2-30. LOUDSPEAKER (35 cm) (SP1)
1
five screws
(TPBV)
1
three screws
(TPBV)
2
Remove the loudspeaker (35 cm) (SP1)
in the direction of the arrow.
3
terminal
(wide
side)
3
terminal
(narrow
side)
4
loudspeaker (35 cm)
(SP1)
OK
NG
Caulking is outside.
Caulking is inside.
,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUZLUH
–%RWWRPYLHZ–
loudspeaker (35 cm)
(SP1)
(SP1)
terminal
(wide side)
(wide side)
:LUHVHWWLQJ
+RZWRLQVWDOOWKHORXGVSHDNHUFP63
–)URQWYLHZ–
loudspeaker (35 cm)
(SP1)
(SP1)
Note 2: When installing the loudspeaker (35 cm) (SP1),
make the position of terminals as shown in the
figure
below.
Note 1: When installing the speaker wire, make the
position of caulking of terminals is outside.
terminals position
terminal
(narrow side)
(narrow side)
SA-WGT5D
39
2-31. SERVICE POSITION
D-AMP board
POWER board
ARAGON-MOTHER board
switching regulator
(SWR1)
(SWR1)
insulating sheet
stand
stand
CDM block
top panel block
SA-WGT5D
40
SECTION 3
TEST MODE
USER RESET
It can clears all data including preset data stored in the memory
to initial conditions (Only the connection history information of
Bluetooth is not initialized).
It can clears all data including preset data stored in the memory
to initial conditions (Only the connection history information of
Bluetooth is not initialized).
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press two buttons of the [ENTER] and [S4 TUNING + >]
simultaneously for three seconds.
3. The message “RESET” is displayed on the fl uorescent indica-
tor tube, then becomes the standby state.
Screen display
TUNER STEP CHANGE
(Except AEP, RU, UK models)
It can change AM step interval into 9 kHz or 10 kHz.
(Except AEP, RU, UK models)
It can change AM step interval into 9 kHz or 10 kHz.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the “TUNER AM”
function.
3. Press the [
?/1
] button to turn the power off.
4. Press two buttons of the [ENTER] and [FOOTBALL] simulta-
neously.
5. The message “9K STEP” or “10K STEP” is displayed on the
fl uorescent indicator tube, and AM step interval changed.
Screen display
or
DISC THEFT PREVENTION
It can be unable to take sample disc out of disc tray in the shop.
It can be unable to take sample disc out of disc tray in the shop.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the “DVD/CD” func-
tion.
3. Press the [
Z
] button to open the disc tray and set the disc.
4. Press the [
Z
] button to close the disc tray.
5. Press two buttons of the [ENTER] and [VOCAL FADER] si-
multaneously for three seconds.
6. The message “LOCKED” is displayed on the fl uorescent indi-
cator tube and the disc tray is locked.
(Even if pressing the [
Z
] button, the message “LOCKED” is
displayed on the fl uorescent indicator tube and the disc tray is
locked)
locked)
Screen display
Releasing method:
1. Press two buttons of the [ENTER] and [VOCAL FADER] si-
1. Press two buttons of the [ENTER] and [VOCAL FADER] si-
multaneously for three seconds.
2. The message “UNLOCKED” is displayed on the fl uorescent
indicator tube and the disc tray is unlocked.
BT PAIRING HISTORY CLEAR
It can clear the pairing history of Bluetooth.
It can clear the pairing history of Bluetooth.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the “BLUETOOTH”
function.
3. Press two buttons of the [ENTER] and [S1 – ] simultane-
ously for three seconds.
4. The message “BT HISTORY”
→ “CLEAR” is displayed on
the fl uorescent indicator tube, and the pairing history of Blue-
tooth is cleared.
tooth is cleared.
Screen display
COLD RESET
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press two buttons of the [
x
] and [S4 TUNING + >] simul-
taneously for three seconds.
3. The
message “COLD RESET” is displayed on the fl uorescent
indicator tube, then becomes the standby state.
Screen display
Ver. 1.1
Click on the first or last page to see other SA-WGT5D service manuals if exist.