Sony SA-WGT5D Service Manual ▷ View online
SA-WGT5D
29
2-20. AC INLET (AC1)
:LUHVHWWLQJ
pipe cover
2
two screws
(BVTP3
u 10)
5
AC inlet
(AC1)
4
himelon
(05)
clamp
clamp
clamp
clamp
clamp
$&LQOHW$&VHWWLQJ
AC inlet
(AC1)
(AC1)
white
black
30 ± 5 mm
75 ± 5 mm
himelon (05)
AC inlet (AC1)
3DVWLQJSRVLWLRQRI
WKHKLPHORQ
WKHKLPHORQ
bottom side
1
Remove the wire
from the clamp.
1
Remove the wire
from the clamp.
1
Remove the wire
from the clamp.
1
Remove the wire
from the clamp.
1
Remove the wire
from the clamp.
3
Remove the AC inlet
block in the direction
of the arrow.
–
3LSHFRYHUEORFNIURQWWRSYLHZ–
pipe cover block
SA-WGT5D
30
2-21. HANDLE BLOCK, BACK PANEL (OUTER) ASSY
3
handle block
– Rear top view –
1
three screws
(BVTP4
u 20)
4
five screws
(BVTP3
u 10)
5
back panel (outer) assy
1
three screws
(BVTP4
u 20)
2
boss
2
boss
SA-WGT5D
31
2-22. TUNER BLOCK, JACK BOARD
3
connector
(CN3301)
2
tuner block
6
JACK board
– Rear top view –
5
Remove the JACK board
in the direction of the arrow.
1
two screws
(BVTP3
u 8)
4
two screws
(BVTP3
u 8)
4
screw
(BVTP3
u 8)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
How to install the connector
Insert the connector straight into the interior.
There is a possibility that using this unit
without the connector correctly installed will
damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit
without the connector correctly installed will
damage it.
3
connector
(CN503)
2
tuner block
6
JACK board
– Rear top view –
5
Remove the JACK board
in the direction of the arrow.
1
two screws
(BVTP3
u 8)
4
two screws
(BVTP3
u 8)
4
screw
(BVTP3
u 8)
(New type)
(Former type)
Ver. 1.1
SA-WGT5D
32
2-23. D-AMP BOARD BLOCK
–
Rear top view
–
2
switching
regulator
cable
connector
(CN2001)
cable
connector
(CN2001)
1
speaker connector
(CN2002)
)OH[LEOHIODWFDEOH))&VHWWLQJ
4
two screws
(BVTP3
u 8)
4
four screws
(BVTP3
u 8)
4
screw
(BVTP3
u 8)
D-AMP board
CN2502
terminal
face
face
3
flexible flat cable (21P) (FFC4)
(CN2502)
A
A
B
B
4
screw
(BVTP3
u 8)
6
D-AMP board block
5
Remove the D-AMP board block
in the direction of the arrow.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
2-24. D-AMP BOARD
4
heat sink (M3)
3
two thermal sheets
1
three screws
(PTPWH2.6
u L)
5
D-AMP board
2
heat sink bracket
Click on the first or last page to see other SA-WGT5D service manuals if exist.