Sony SA-SLRT5 / SA-SRRT5 Service Manual ▷ View online
SA-SLRT5/SRRT5
5
NOTE OF REPLACING THE AMP IC ON THE REAR
MAIN BOARD OR THE REAR MAIN BOARD
When AMP IC (SA-SLRT5: IC8203, SA-SRRT5: IC9203) on the
REAR MAIN board or the REAR MAIN board are replaced, it
is necessary to spread the compound between the REAR MAIN
board and the heat sink.
Spread the compound referring to the fi gure below.
MAIN BOARD OR THE REAR MAIN BOARD
When AMP IC (SA-SLRT5: IC8203, SA-SRRT5: IC9203) on the
REAR MAIN board or the REAR MAIN board are replaced, it
is necessary to spread the compound between the REAR MAIN
board and the heat sink.
Spread the compound referring to the fi gure below.
– REAR MAIN Board (Side A) –
IC8203 (SA-SLRT5)
IC9203 (SA-SRRT5)
IC9203 (SA-SRRT5)
compound
NOTES ON THE WIRELESS CONNECTION (LINK) AF-
TER REPAIRS ARE COMPLETE
When the following replacing repair is performed, the link of the
Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and Surround
speaker (SA-SLRT5/SRRT5) is cut.
Return the Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and
Surround speaker (SA-SLRT5/SRRT5) to the customer after per-
forming the link according to the following procedure.
TER REPAIRS ARE COMPLETE
When the following replacing repair is performed, the link of the
Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and Surround
speaker (SA-SLRT5/SRRT5) is cut.
Return the Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and
Surround speaker (SA-SLRT5/SRRT5) to the customer after per-
forming the link according to the following procedure.
Parts in which the LINK will be disconnected due to re-
placement:
•
placement:
•
Complete REAR MAIN board
Link method:
When you turn on the Bar speaker (SA-RT5), Subwoofer (SA-
WRT5) and Surround speaker (SA-SLRT5/SRRT5), and then au-
tomatically link.
If do not automatically link, there is a possibility that the customer
is perform the secure link. In that case, perform the following pro-
cedure.
When you turn on the Bar speaker (SA-RT5), Subwoofer (SA-
WRT5) and Surround speaker (SA-SLRT5/SRRT5), and then au-
tomatically link.
If do not automatically link, there is a possibility that the customer
is perform the secure link. In that case, perform the following pro-
cedure.
Procedure of secure link:
1
Select [Wireless Sound Connection] in [System Settings].
2
Select [Secure Link].
3
Select [On].
4
Press SECURE LINK on the rear of the subwoofer and the
surround speakers until the indicator turns orange.
Proceed to the next step within a few minutes.
surround speakers until the indicator turns orange.
Proceed to the next step within a few minutes.
5
Select [Start].
To return to the previous display, select [Cancel].
To return to the previous display, select [Cancel].
6
After the message [Secure Link setting is complete.] appears,
press
press
.
If the message [Cannot set Secure Link.] appears, follow the
on-screen instructions.
on-screen instructions.
Note: If customer had perform a secure link, only the Surround speaker
is brought in for repair and the REAR MAIN board is replaced, be
sure to inform the customer when returning the repaired products
that the customer must secure link again the Bar speaker, Subwoofer
and Surround speaker.
sure to inform the customer when returning the repaired products
that the customer must secure link again the Bar speaker, Subwoofer
and Surround speaker.
(Indicate that the secure link procedure is described in the operating
instructions)
THE ON/STANDBY INDICATOR FLASHES IN RED
–Press
(on/standby) of the surround speakers to turn off the
power and check whether the ventilation opening of the
surround speakers is blocked or not.
surround speakers is blocked or not.
BOND FIXATION OF ELECTRIC PARTS
When the following parts are replaced, fi x the parts by using the
bond (SC608Z2) (Refer to the fi gure below).
When the following parts are replaced, fi x the parts by using the
bond (SC608Z2) (Refer to the fi gure below).
Note: If you replaced the switching regulator (3L409W) to new parts,
there are cases where that parts arrives already been bond fi xed.
Only if the arrived new switching regulator (3L409W) is not bond
fi xed, do the bond fi xation operation in the position of fi gure below.
Target parts:
•
•
Switching regulator (3L409W)
C201
– SWITCHING REGULATOR (3L409W)
(Component Side) –
(Component Side) –
L401
C402
C101
NR101
Heat sink
Board
C101
R202
TH101
RC201
SA-SLRT5/SRRT5
6
NOTES WHEN REPLACING THE SPEAKER CABINET
ASSY
The shape of the speaker cabinet assy has been changed in the
middle of production. When replacing the speaker cabinet assy,
make sure to refer to the fi gure below and check its type before
replacement.
ASSY
The shape of the speaker cabinet assy has been changed in the
middle of production. When replacing the speaker cabinet assy,
make sure to refer to the fi gure below and check its type before
replacement.
– Side view –
Former type: 5 mm
New type: 7 mm
speaker cabinet assy
(Rear view)
Ver. 1.2
SA-SLRT5/SRRT5
7
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. GRILLE
FRAME
ASSY
(Page
8)
2-3. BAFFLE BOARD BLOCK
(Page
(Page
9)
2-5. POWER
CORD
(Page
11)
2-6. BUTTON,
SPEAKER
CABINET
ASSY
(Page
11)
2-9. REAR MAIN BOARD
(Page
(Page
13)
2-10. SPEAKER (57 mm)
(Page
(Page
14)
2-4. AMP
BLOCK
(Page
10)
2-7. SWITCHING
REGULATOR
(Page
12)
2-8. RF MODULATOR
(Page
(Page
13)
•
JIG
When disassembling the unit, use the following
jig for speaker removal.
jig for speaker removal.
Part No.
Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
Note 1: L-ch and R-ch can be similarly disassembled.
soft cloth, etc.
bottom side
top side
soft cloth, etc.
top side
bottom side
soft cloth, etc.
left side
right side
soft cloth, etc.
right side
left side
Note 2: When placing the top, bottom, left, or right side of the unit face down
for assembly/disassembly, lay down a soft cloth, etc. under the unit to
avoid damaging it before proceeding.
SA-SLRT5/SRRT5
8
Note: Follow the disassembly procedure in the numerical order given.
2-2. GRILLE FRAME ASSY
3 Remove the grille frame assy
in the direction of the arrow.
total ten bosses
soft cloth, etc.
4 grille frame assy
Note
2: When installing the grille frame assy,
remove the attached bond, apply a new
bond to the six bosses, and then fix the
grille frame assy.
2 While moving the jig in the
direction of the arrow,
remove all bosses.
2 While moving the jig in the
direction of the arrow,
remove all bosses.
1 Insert the jig into the space and slowly
remove the grille frame assy.
Note
1: When using a jig, please work
carefully so as not to damage the
grille frame assy and speaker cabinet.
1 Insert the jig into the space and slowly
remove the grille frame assy.
Note
1: When using a jig, please work
carefully so as not to damage the
grille frame assy and speaker cabinet.
Where a bond is to be applied.
(total six bosses)
(total six bosses)
speaker
cabinet
cabinet
grille frame assy
Click on the first or last page to see other SA-SLRT5 / SA-SRRT5 service manuals if exist.