Sony SA-NS410 Service Manual ▷ View online
SA-NS410
9
2-7. WIRELESS LAN MODULE (12SA-NS410) (MOD1), MAIN BOARD
1 screw (BV3)
1 screw (BV3)
6 MAIN board
4 BCO cushion
5 cushion (LED)
cushion (LED)
D107
MAIN board
3 wireless LAN module
(12SA-NS410)
(MOD1)
2 connector
(CN104)
– MAIN board rear bottom side view –
Note 2: When installing the cushion (LED),
do not overlap on D107.
2-8. FERRITE CORE (FC1)
– Bottom side view –
Note 1: Please spread a sheet under the unit
not to injure top panel.
Note 2: PEF (ferrite) is bent on the reverse side and
keep ferrite core (FC1) from overflowing.
1
cushion (FIX)
4
PEF (ferrite)
PEF (ferrite)
5
ferrite core (FC1)
ferrite core (FC1)
2 floating screw
(PTPWHM2.6)
3
Remove the antenna wire
in the direction of an arrow.
Ferrite core (FC1) setting
cushion (FIX)
ferrite core
(FC1)
(FC1)
floating screw
(PTPWHM2.6)
(PTPWHM2.6)
antenna wire
Antenna wire setting
Note 1: When replacing the wireless LAN module (12SA-NS410) (Ref. No.
MOD1), refer to “NOTE OF REPLACING THE WIRELESS LAN
MODULE (12SA-NS410)” and “PROCESSING OF REPLACING
THE WIRELESS LAN MODULE (12SA-NS410)” (page 3)
MODULE (12SA-NS410)” and “PROCESSING OF REPLACING
THE WIRELESS LAN MODULE (12SA-NS410)” (page 3)
SA-NS410
10
2-9. E-BOX BLOCK
2-10. LOUDSPEAKER (11 cm) (SP5)
4 E-box block
3
Remove the antenna wire
in the direction of an arrow.
1
Remove the E-box block
in the direction of an arrow.
2
Remove two speaker wires
in the direction of an arrow.
– Rear bottom side view –
antenna wire
antenna wire
The cushion (D) has
come out.
come out.
The cushion (D) has
not come out.
not come out.
OK
NG
Antenna wire setting
Note: Please spread a sheet under the unit
not to injure top panel.
1 two screws (3.5)
1 two screws (3.5)
terminal position
2
Remove the loudspeaker (11 cm)
(SP5) in the direction of an arrow.
4
loudspeaker (11 cm) (SP5)
loudspeaker (11 cm) (SP5)
3
terminal
(black)
terminal (black)
terminal (black)
3
terminal
(red)
terminal (red)
terminal (red)
Note 3: When installing two terminals, check
being inserted completely.
Note 4: When installing the loudspeaker (11 cm) (SP5),
check that terminals are on right side.
OK
loudspeaker
Inserted completely
NG
loudspeaker
Inserted shallowly.
Note 1: Please spread a sheet under the unit
not to injure top panel.
Note 2: Do not touch speaker cone area.
– Rear bottom side view –
Front
Rear
Left
Right
SA-NS410
11
2-11. FRONT GRILL ASSY, REAR GRILL ASSY
L
3 front grill assy
Note
2: When installing the front grill assy,
remove the used bond and use a new
bond to fix the front grill assy.
(No specific bond is designated for
this
purpose)
4 rear grill assy
Note 2: When installing the rear grill assy,
remove the used bond and use a new
bond to fix the rear grill assy.
(No specific bond is designated for
this
purpose)
1 Insert the jig into a space and raise
front grill assy and rear grill assy.
Note
1: When using a jig, please work
so as not to injure front grill
assy and rear grill assy.
1 Insert the jig into a space and raise
front grill assy and rear grill assy.
Note
1: When using a jig, please work
so as not to injure front grill
assy and rear grill assy.
2
2
All bosses are removed while
moving jig in the direction of
the arrow, and front grill assy
is
removed.
total eighteen bosses
– Left side view –
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
SA-NS410
12
2-12. ANTENNA BLOCK
Note: In order to remove the antenna block, it is necessary to remove the rear grill assy.
L
2 screw (3.5)
1 cushion
(T0.5)
3 antenna block
antenna
$QWHQQDZLUHVHWWLQJ
cushion (T0.5)
guide line
guide line
–/HIWVLGHYLHZ–
2-13. ANTENNA (ANT1)
2 cushion (ANT)
5 antenna
(ANT1)
antenna (ANT1)
antenna (ANT1)
4 conductive tape
(ANT
cable)
conductive tape
(ANT cable)
(ANT cable)
The terminal side is a top.
3 cushion (D)
cushion (D)
cushion (D)
conductive tape
(ANT cable)
(ANT cable)
The terminal side is a bottom.
The soldering side
is a bottom.
is a bottom.
It has pasted
together firmly.
together firmly.
The soldering side
is a top.
is a top.
1 ANT holder
OK
NG
$QWHQQDZLUHVHWWLQJ
There is a crevice.
The portion cut
off is the direction
of a terminal.
off is the direction
of a terminal.
terminal
cushion (D)
OK
NG
OK
NG
Note: The antenna must not touch
empty-handed.
empty-handed.
Be careful of the portion
enclosed with especially a
dotted
line.
Click on the first or last page to see other SA-NS410 service manuals if exist.