Sony SA-NS410 Service Manual ▷ View online
SA-NS410
5
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-3. BOTTOM PANEL BLOCK
(Page
(Page
6)
2-4. ANTENNA
CONNECTOR
(Page
7)
2-5. MAIN BOARD BLOCK
(Page
(Page
8)
2-7. WIRELESS LAN MODULE
(12SA-NS410)
(12SA-NS410)
(MOD1),
MAIN
BOARD
(Page
9)
2-6. SHIELD T, SHIELD B BLOCK
(Page
(Page
8)
2-2. HOW TO BEND FLEXIBLE FLAT CABLE
(Page
(Page
5)
2-8. FERRITE CORE (FC1)
(Page
(Page
9)
2-11. FRONT GRILL ASSY,
REAR
REAR
GRILL
ASSY
(Page
11)
2-9. E-BOX
BLOCK
(Page
10)
2-12. ANTENNA BLOCK
(Page
(Page
12)
2-14. TOP PANEL BLOCK
(Page
(Page
13)
2-15. TWEETER BLOCK
(Page
(Page
14)
2-13. ANTENNA (ANT1)
(Page
(Page
12)
2-10. LOUDSPEAKER
(11 cm) (SP5)
(Page
10)
2-16. LOUDSPEAKER (3 cm)
(SP1, SP2, SP3, SP4)
(Page
15)
2-2. HOW TO BEND FLEXIBLE FLAT CABLE
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R))&
MAIN board
(CN101)
PANEL board
(CN900)
: Mountain fold
: Valley fold
: Valley fold
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
45 mm
45 mm
45°
90°
25 mm
SA-NS410
6
Note: Follow the disassembly procedure in the numerical order given.
2-3. BOTTOM PANEL BLOCK
– Rear bottom side view –
2 tapping screw
(3.5
u 20)
2 tapping screw
(3.5
u 20)
2 tapping screw
(3.5
u 20)
2 tapping screw
(3.5
u 20)
2 tapping screw
(3.5
u 20)
2 tapping screw
(3.5
u 20)
1 foot
1 foot
1 foot
4 bottom panel block
Jacks has fitted in correctly.
The bottom panel has run
aground to the jack.
aground to the jack.
Note 3: When installing the bottom
panel block, check that each
jack has fitted in certainly.
Note 1: Please spread a sheet under the unit
not to injure top panel.
OK
NG
button PWR
switch (S100)
MAIN board
Note 2: When installing the bottom panel block,
match the position of the button PWR
and the switch (S100).
3 Remove the bottom panel block
in the direction of an arrow.
Switch (S100) position
is “OFF”.
is “OFF”.
Switch (S100) position
is “ON”.
is “ON”.
Button PWR position is
“STANDBY”.
“STANDBY”.
Button PWR position is
“NETWORK STANDBY”.
“NETWORK STANDBY”.
1 foot
OK
NG
SA-NS410
7
2-4. ANTENNA CONNECTOR
4
cushion (fix)
4
cushion (fix)
3
flexible flat cable (11 core)
(CN101)
2
cushion (fix)
1 connector
(CN109)
5
antenna connector
(CON2)
connector
Insert is incline
connector
connector
connector
connector
connector
NG
Note 3: When you install the flexible flat cable, please install them correctly. There
is a possibility that this machine damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
Insert is incline
OK
– Bottom side view –
Note 1: Please spread a sheet under the unit
not to injure top panel.
coloured line
coloured line
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
NG
coloured line
flexible flat
cable
cable
connector
NG
flexible flat cable (11 core)
shield T
Note 4: Put the flexible flat cable in order
under the shield T.
Flexible flat cable (11 core) setting
cushion (fix)
MAIN board
Note 2: When you install the connector, please install them correctly. There is a
possibility that this machine damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
NG
OK
antenna wire
cushion (fix)
antenna wire
wireless LAN module
(12SA-NS410)
(12SA-NS410)
OK
NG
Note 6: Check the thing to which the wire is not slanting,
which have not floated and from which it has not
disconnected.
connector
connector
antenna wire
antenna wire
OK
NG
Note 5: There are two terminals for
antenna wire in a module.
When connecting the antenna
wire, connect with the right
terminal.
SA-NS410
8
2-6. SHIELD T, SHIELD B BLOCK
2-5. MAIN BOARD BLOCK
3 two screws
(BVTP3
u 12)
3 two screws
(BVTP3
u 12)
4 MAIN board block
– Bottom side view –
Note 1: Please spread a sheet under the unit
not to injure top panel.
MAIN board
MAIN board
The boss has come out.
The boss has not come out.
Note 3: When installing the MAIN board block,
match the position of hole and boss.
OK
NG
Note 3: When installing the MAIN board block,
match the position of hole and boss.
MAIN board
MAIN board
The boss has come out.
The boss has not come out.
OK
NG
2 connector
(CN108)
1 connector
(CN107)
Note 2: Arrange a wire inside a board.
Wire setting
MAIN board
2 shield T
1 three screws
(BV3)
1 screw
(BV3)
3
Remove the shield B block
in the direction of an arrow.
4
shield B block
CN100
J100
J101
– MAIN board block rear bottom side view –
Note: When installing the shield B block,
insert CN100, J100 and J101 in each
hole.
Click on the first or last page to see other SA-NS410 service manuals if exist.