Sony NWZ-E463 / NWZ-E463HK / NWZ-E463K / NWZ-E464 / NWZ-E464K / NWZ-E465 Service Manual ▷ View online
NWZ-E463/E463HK/E463K/E464/E464K/E465
9
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE (FRONT) ASSY
panel (rear) assy block
case (front) assy
case (front) assy
Right side:
Left side:
1
two screws
(P2
M1.4)
3
six claws
4
two claws
5
case (front) assy
2
Insert your nail in the gap between case
(front) assy and panel (rear) assy block.
Then slide it to arrow direction to remove
claws of panel (rear) assy block.
2
Insert your nail in the gap between case
(front) assy and panel (rear) assy block.
Then slide it to arrow direction to remove
claws of panel (rear) assy block.
– Rear side view (bottom side) –
panel (rear) assy block
NWZ-E463/E463HK/E463K/E464/E464K/E465
10
2-3. CASE (REAR) ASSY BLOCK
guide (hold)
switch
Note: When installing panel (rear) assy
block, the position of switch and
guide (hold) is set and installed.
1
screw
(B1.4)
3 guide (hold)
4 case (rear) assy block
2
2-4. OPEN THE SHORT-LAND
Note 1: This illustration sees the mechanical commonness block from LCD assy side.
Note 2: Make sure to remove one solder to become an open state before disassembling the mechanical commonness block.
Note 3: Solder the short-land after all wirings are connected when you exchanged some mounted board.
Note 2: Make sure to remove one solder to become an open state before disassembling the mechanical commonness block.
Note 3: Solder the short-land after all wirings are connected when you exchanged some mounted board.
1 Remove the solder of short-land (SL9501).
NWZ-E463/E463HK/E463K/E464/E464K/E465
11
2-5. EMMC BOARD
2-6. VOL KEY ASSY
3
1 cushion (NAND)
4 spacer (NAND)
– Rear side view –
2 connector
Note: Lift vertically the EMMC board
when you remove the connector.
5 EMMC board
VOL key wire
VOL key wire
:LUHSURFHVVLQJRI92/NH\ZLUH
red
green
4 sheet (wire)
7 sheet (chassis)
8 VOL key assy
VOL key assy
5
3 sheet (PWB)
6 Remove two solders of
VOL key wire.
–5HDUVLGHYLHZ–
1 cushion (NAND)
2 Peel the copper leaf (coral).
NWZ-E463/E463HK/E463K/E464/E464K/E465
12
2-7. SUPPORT
(M)
2-8. 3PIN HP JACK BLOCK
2 sheet (PWB)
2 sheet (PWB)
1 Peel the copper leaf (coral).
3 Lift wires of battery assy (BAT1).
4 boss
4 boss
7 support (M)
support (M)
– Rear side view –
5
6 marking label
Note: When you exchanged the support (M), peel off the marking
label from the old support (M) before it exchanges it, and
try to paste it to the new support (M).
(NWZ-E463K/E464K)
Wire SrRFessiQJ RI EaWWer\ ass\ (%$7)
wire of battery
assy (BAT1)
assy (BAT1)
1 two claws
5 three claws
6
4 screw (M1.4)
3 3pin HP jack assy flexible board
7 3pin HP jack block
2 escutcheon
– Rear top side view –
Click on the first or last page to see other NWZ-E463 / NWZ-E463HK / NWZ-E463K / NWZ-E464 / NWZ-E464K / NWZ-E465 service manuals if exist.