Sony NW-A1000 Service Manual ▷ View online
NW-A1000
5
Note:
Follow the disassembly procedure in the numerical order given.
3-2. CABINET (LOWER)
•
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3
claw
1
ornament (strap)
2
adhesive sheet (strap)
4
Remove the cabinet (lower)
in the direction of the arrow.
in the direction of the arrow.
Note: Execute the confirmation and the inspection of the correct repair of all parts after it repairs.
And, install ornament (strap) and adhesive sheet (strap) after confirming the repair ended completely.
3-2. CASE (LOWER)
(Page 5)
3-3. LITHIUM ION BATTERY
(Page 6)
3-4. CABINET (INNER)
(Page 6)
3-5. EL BLOCK SUB ASSY
(Page 7)
3-6. MAIN BOARD
(Page 7)
SET
NW-A1000
6
3-3. LITHIUM ION BATTERY
3-4. CABINET (INNER)
3
bracket (HDD)
2
two screws
(B1.4)
(B1.4)
1
two sheets (electrostatic CU)
4
two screws
(B1.4)
(B1.4)
6
connector (CN9001)
7
lithium ion battery
5
Note: Do not close the hole of bracket (HDD) when you paste the sheets (electrostatic CU).
hole
2
two claws
sheet (cabinet inner) (AEP, UK, Tourist, Korean)
2
two claws
3
cabinet (upper)
5
sheet (cabinet)
(Canadian, Singapore,
Australian, Chinese)/
sheet (ESD)
(AEP, UK, Tourist, Korean)
(Canadian, Singapore,
Australian, Chinese)/
sheet (ESD)
(AEP, UK, Tourist, Korean)
4
cabinet (inner) sub assy
button side
cabinet (upper)
ditch
1
sheet (HD)
tweezers
1
sheet (HD)
2
sheet (HD)
3
1
Hang claw and ditch of cabinet (upper) completely.
Note: Do not damage it
when you peel off sheet (ESD)
from sheet (cabinet inner).
from sheet (cabinet inner).
tweezers
claw
-BOTTOM VIEW-
– Installation procedure of sheet (HD) –
Ver. 1.5
NW-A1000
7
3-5. EL BLOCK SUB ASSY
3-6. MAIN BOARD
1
sheet
(electric static G)
(electric static G)
1
sheet
(electric static G)
(electric static G)
3
button assy
4
two step screws
5
two step screws
6
8
connector
(CN8302)
(CN8302)
9
EL block sub assy
7
connector
(CN8301)
(CN8301)
boss
hole
slit
boss
2
Remove sheet
(electrostatic CU)
(electrostatic CU)
2
Remove sheet
(electrostatic CU)
(electrostatic CU)
Note: On installation of EL block sub assy,
adjust the position of two bosses
and slit or hole.
and slit or hole.
Note: On installation of sheet (electrostatic CU),
pass the sheet (electrostatic CU)
through this ditch.
through this ditch.
6
MAIN board
3
insulator (CF1)
3
insulator (CF1)
5
HDD unit
4
connector unit
connector unit
HDD unit
"HITACH" or "Seagate" is printed.
1
connector
(CN5001)
(CN5001)
2
knob (VOL)
S8301
Note: On installation of MAIN board,
adjust the position of switch (S8301)
and knob (VOL).
and knob (VOL).
Note: On installation of connector unit, Take care in the direction of HDD unit.
NW-A1000
8
3-7. POSITION OF FERRITE CORE
2cm
A cable is rolled onece.
clamp filter (ferrite core) (Part No. : 1-500-386-11)
-AC POWER CORD-
Ver. 1.2
Click on the first or last page to see other NW-A1000 service manuals if exist.