Sony ICD-UX532 / ICD-UX533 / ICD-UX533F / ICD-UX534F Service Manual ▷ View online
ICD-UX532/UX533/UX533F/UX534F
9
2-6. ELECTRET CAP MICROPHONE BLOCK (L-ch)
2-7. MAIN BOARD
1
Remove two solders.
2
electret cap microphone block (L-ch)
MAIN board
electret cap
microphone
block (L-ch)
microphone
block (L-ch)
blue
white
:LUHVHWWLQJ
–)URQWWRSVLGHYLHZ–
1
Remove two solders.
1
Remove two solders.
1
Remove two solders.
8
sheet
(noise
control)
control)
7
connector
9
MAIN board
2
battery terminal (
−)
3
battery terminal (
+)
4
USB flexible board
5
screw (B1.4)
5
two screws
(B1.4)
(UX533F/
UX534F)
UX534F)
– Front top side view –
6
Remove the MAIN board
in the direction of an arrow.
MAIN board
black
black
red
red
Wire setting
Note 2: When replacing MAIN board, refer to “ABOUT THE
DESTINATION SETTING WHEN REPLACING THE
MAIN BOARD” on page 4.
MAIN BOARD” on page 4.
Note 1: When the MAIN board is replaced, the setup of LCD
backlight is required. Perform the setup of LCD back-
light with reference to “4-2. LCD BackLight” (page 13)
on test mode.
light with reference to “4-2. LCD BackLight” (page 13)
on test mode.
ICD-UX532/UX533/UX533F/UX534F
10
2-9. USB ASSY (USB1)
2-8. ELECTRET CAP MICROPHONE BLOCK (R-ch)
electret cap
microphone
block (R-ch)
microphone
block (R-ch)
loudspeaker (2.0 cm)
boss
claw
1
electret cap
microphone
block
block
(R-ch)
:LUHVHWWLQJ
–6HFWLRQDOYLHZ–
speaker wire
microphone wire
claw
boss
–)URQWWRSVLGHYLHZ–
1 screw
(M1.4)
4 knob (USB)
2 claw
5 USB assy (USB1)
shaft
hole
Note: When installing USB assy, align the shaft of
USB assy and the hole of knob (USB).
– Front top side view –
3
Remove the USB assy
in the direction of an arrow.
ICD-UX532/UX533/UX533F/UX534F
11
2-10. SLOT BOARD
1 two claws
2 SLOT board
– Front top side view –
ICD-UX532/UX533/UX533F/UX534F
12
SECTION 3
TEST MODE
1. SETTING THE TEST MODE
Note: Test mode is impossible when battery voltage is not enough.
Do work using the battery with suffi cient battery level.
Setting method:
1. Equip this unit with battery.
2. Slide the [HOLD•POWER] switch in the direction of “POW-
1. Equip this unit with battery.
2. Slide the [HOLD•POWER] switch in the direction of “POW-
ER” until the window display appears.
HOLD
POWER
3. Slide the [DPC (SPEED CTRL)] switch to OFF.
DPC (SPEED CTRL) OFF
ON
4. While pressing the [STOP/
x
] and [VOL –] keys, slide the
[DPC (SPEED CTRL)] switch to ON.
DPC (SPEED CTRL) OFF
ON
STOP/x
VOL –
5. The test mode menu is displayed, and enter the test mode. Re-
lease the [STOP/
x
] and [VOL –] keys.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
<SERVICE MENU>
ICD-UX532/CN
1.00.01
1.00.01
Destination
Model name
Firmware version
Model name
Firmware version
LCD Display
2. RELEASING THE TEST MODE
Remove battery.
Remove battery.
3. CONFIGURATION OF THE TEST MODE
[
.
] key
[
>
] key
J
j
k
K
Normal mode
Slide the [DPC (SPEED CTRL)] switch to OFF.
While pressing the [STOP/
x
] and [VOL –] keys,
slide the [DPC (SPEED CTRL)] switch to ON.
Release the [STOP/
x
] and [VOL –] keys.
Remove battery.
Initial state of test mode
End of test mode
Determine
using
[
N
]
key
Return using
[STOP/
x
] key
SERVICE MENU
VERSION
LCD BackLight
KEY CHECK
AUDIO LOOP
LCD BL_Manual
SIN
BEEP
LCD CONT
LCD PATTERN
RTC TEST
BATT A/D
ZLOAD
LOW DET
VBUS
FM TEST
KEY COUNT
SLEEP
BATT LIFE
WRITER VER
CHG LOG
LREC LOG
LREC LOG Clear
MENU INIT
SERVICE MENU
Click on the first or last page to see other ICD-UX532 / ICD-UX533 / ICD-UX533F / ICD-UX534F service manuals if exist.