Sony ICD-PX333 / ICD-PX333D / ICD-PX333F / ICD-PX333M Service Manual ▷ View online
ICD-PX333/PX333D/PX333F/PX333M
9
2-5. SPEAKER
(SP1)
2-6. LCD HOLDER
Note: When installing the speaker (SP1),
align the speake wire with the ditch .
– Case (front) block rear bottom view –
1
tapping screw
(B2.0)
1
tapping screw
(B2.0)
2
speaker
(SP1)
1
claw
1
claw
1
claw
boss
boss
hole
hole
1
claw
– MAIN board block front top view –
2
LCD holder
Note: When installing the LCD holder,
Note: When installing the LCD holder,
align two bosses with two holes.
Speaker wire is
in the groove.
in the groove.
Speaker wire is run
aground to the MAIN
board.
aground to the MAIN
board.
Microphone wire setting
OK
NG
ICD-PX333/PX333D/PX333F/PX333M
10
2-7. ELECTRET CAP MICROPHONE (MIC1), MAIN BOARD
1
Remove two solders.
3
electret cap microphone
(MIC1)
4
sheet
(insulating)
sheet (insulating)
6
MAIN board
2
cushion (MIC)
MAIN board
Speaker wire is
in the groove.
in the groove.
Speaker wire is run
aground to the MAIN
board.
aground to the MAIN
board.
electret cap microphone block
[red]
[black]
MAIN board
MAIN board
0LFURSKRQHZLUHVHWWLQJ
6KHHWLQVXODWLQJVHWWLQJ
5
sheet
(noise
control)
sheet
(noise control)
(noise control)
–0$,1ERDUGEORFNIURQWWRSYLHZ–
3;)
OK
1*
guide line
C318
guide line
land
guide line
IC104
6KHHWQRLVHFRQWUROVHWWLQJ
ICD-PX333/PX333D/PX333F/PX333M
11
SECTION 3
TEST MODE
1. SETTING THE TEST MODE
Note: Test mode is impossible when battery voltage is not enough.
Do work using the battery with suffi cient battery level.
Setting method:
1. Equip this unit with battery.
2. Slide the [HOLD•POWER ON/OFF] switch in the direction of
1. Equip this unit with battery.
2. Slide the [HOLD•POWER ON/OFF] switch in the direction of
“POWER” until the window display appears.
3. Slide the [HOLD•POWER ON/OFF] switch to “HOLD OFF”
(center).
4. While pressing the [
x
] and [VOL –] keys, slide the [HOLD•POWER
ON/OFF] switch in the direction of “HOLD”.
VOL –
x
5. The test mode menu is displayed, and enter the test mode. Re-
lease the [
x
] and [VOL –] keys.
<SERVICE MENU>
LCD Display
2. RELEASING THE TEST MODE
Remove battery.
Remove battery.
3. CONFIGURATION OF THE TEST MODE
[
.
] key
[
>
] key
J
j
k
K
Normal mode
6lLde WKe [+2/'32:(5 2N2))] VZLWFK
Wo ³+2/' 2))´ FeQWer
:KLle SreVVLQJ WKe [
x
] aQd [92/ ±] keyV
VlLde WKe [+2/'32:(5 2N2))] VZLWFK
LQ WKe dLreFWLoQ oI ³+2/'´
5eleaVe WKe [
x
] aQd [92/ ±] keyV
5emoYe EaWWery
,QLWLal VWaWe oI WeVW mode
(Qd oI WeVW mode
'eWermLQe
XVLQJ
[3/$<6723
N
(N7(5]
key
5eWXrQ XVLQJ
[
x
] key
6(59,&( 0(N8!
9(56,2N!
.(< &+(&.!
$8',2 /223!
6,N!
%((3!
/&' &2N7!
/&' 3$77(5N!
57& 7(67!
%$77 $'!
=/2$'!
/2: '(7!
9%86!
)0 7(67!
.(< &28N7!
6/((3!
%$77 /,)(!
&+* /2*!
0(N8 ,N,7!
6(59,&( 0(N8!
ICD-PX333/PX333D/PX333F/PX333M
12
4. OPERATION OF THE TEST MODE
4-1. VERSION
Model name, destination, fi rmware version, initial language,
charge function, card function, radio function, eMMC maker code
eMMC capacity, IPL2 version and CPU version, can be confi rmed.
4-1. VERSION
Model name, destination, fi rmware version, initial language,
charge function, card function, radio function, eMMC maker code
eMMC capacity, IPL2 version and CPU version, can be confi rmed.
Procedure:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
>
] or [
.
] keys to select the “VERSION”, and
press the [PLAY/STOP
N
ENTER] key.
3. Model name, destination and fi rmware version are displayed
on page 1/3 of LCD display. Press the [
>
] key, initial lan-
guage, charge function, card function, radio function, eMMC
maker code and eMMC capacity are displayed on page 2/3 of
LCD display. Press the [
maker code and eMMC capacity are displayed on page 2/3 of
LCD display. Press the [
>
] key, IPL2 version and CPU ver-
sion are displayed on page 3/3 of LCD display.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
ICD-PX333 /U
MAINFW:1.00.00
MAINFW:1.00.00
LCD of Display (page 1/3)
LCD of Display (page 2/3)
LCD of Display (page 3/3)
Firmware version
Model name/Destination
L:US C0M1R0
eMMC 15 04GB
eMMC 15 04GB
eMMC capacity
IPL2FW:1.00.00
LSI 4252
LSI 4252
CPU version
IPL2 version
Initial language
Charge function
Memory card function
Radio function
eMMC maker code
C/M/R : 1 = function exists
0 = function non-exists
Releasing method:
Press the [
Press the [
x
] key, return to test mode menu.
4-2. KEY CHECK
Operation of keys and switches can be checked, and this unit can
return to the factory shipment settings.
Operation of keys and switches can be checked, and this unit can
return to the factory shipment settings.
Note 1: It cannot move to other modes from this mode.
Procedure:
1. Enter the test mode.
2. Press
1. Enter the test mode.
2. Press
the
[
>
] or [
.
] keys to select the “KEY CHECK”,
and press the [PLAY/STOP
N
ENTER] key.
3. Whenever any keys of this unit are pressed or any switches of
this unit are slid, the button count decreases.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
LCD Display
KEY:PLAY
16
/
Confirmed key name
Button count
<KEY CHECK>
Target keys:
[
x
], [>], [.], [PLAY/STOP
N
ENTER], [REC/PAUSE
z
],
[
A
-B], [ERASE], [VOL +], [VOL –], [ MENU DISP] [
],
[T-MARK], [SCENE]
Target switches:
[NOISE CUT] (ON, OFF), [HOLD•POWER ON/OFF] (“POW-
ER” direction, return from “POWER” direction, “HOLD” di-
rection, return from “HOLD” direction)
ER” direction, return from “POWER” direction, “HOLD” di-
rection, return from “HOLD” direction)
4. After all the keys and switches are decided, initialization is
performed.
5. “Success” is displayed, and this unit reboots.
LCD Display
Success
SHQ
01
/
Note 2: This unit is not initialized when “ERROR” is displayed.
Releasing method:
Remove battery.
Remove battery.
Click on the first or last page to see other ICD-PX333 / ICD-PX333D / ICD-PX333F / ICD-PX333M service manuals if exist.