Sony ICD-MX20DR9 Service Manual ▷ View online
7
ICD-MX20DR9
2-5. SPEAKER (SP3001) ASSEMBLY
2-6. CASE (REAR), ORNAMENTAL BELT (L), ORNAMENTAL BELT (R)
1
screw
3
screw
2
bracket (speaker)
5
speaker (SP3001)
4
bracket (speaker)
4
ornamental belt (L) assembly
7
case (rear)
(Being attached by adhesive sheet)
3
button (side)
6
screw (M1.4
×
1.6)
5
screw (M1.4
×
1.6)
2
ornamental belt (R)
1
lid (connector)
8
ICD-MX20DR9
2-7. SWITCH BOARD
2-8. MAIN BOARD, SWITCH UNIT
5
SWITCH board
1
connector (CN9502)
4
connector (CN9902)
3
two claws
2
spacer (pc board A)
2
connector (CN9101)
3
connector (CN9904)
5
connector (CN4103)
6
four claws
4
MAIN board, switch unit
1
Peel off the adhesive sheet
on the back of the switch unit.
qs
switch unit
qh
MAIN board
qf
Peel off the adhesive part.
qg
guide (connector)
qd
two dowels
qa
LCD holder
q;
two dowels
7
Peel off the adhesive part.
9
liquid crystal display panel
8
light guide plate
9
ICD-MX20DR9
2-9. AUDIO BOARD, MEMORY BOARD
2
screw
3
AUDIO board
7
MEMORY board
1
cover (chassis)
6
battery terminal (+)
5
battery terminal (–)
4
Remove the
two solderings.
10
ICD-MX20DR9
[Test Mode]
The following checks can be implemented using the Test Mode.
How to Enter the Test Mode
To enter the test mode, turn ON the HOLD switch while pressing
the MENU key and VOLUME + key at the same time with the
power on.
To enter the test mode, turn ON the HOLD switch while pressing
the MENU key and VOLUME + key at the same time with the
power on.
How to Exit the Test Mode
Exit the test mode by turning OFF the power.
Exit the test mode by turning OFF the power.
Initial Status of the Test Mode
When the machine enters the test mode, the LCD display appears
as shown below.
When the machine enters the test mode, the LCD display appears
as shown below.
Select the desired item by using the > / . key, and press the
Nx button to set the selection.
Nx button to set the selection.
1. Version test
•
Version of the respective modules are verified.
2. Key Chk + Format test
•
Perform the key check by pressing the keys. The NAND
formatting (deleting all events) and the default settings of the
menus (default language and LCD contrast remain unchanged)
are executed at the same time.
formatting (deleting all events) and the default settings of the
menus (default language and LCD contrast remain unchanged)
are executed at the same time.
*
Nx / > / . / MENU /
/ REC/PAUSE zX /
STOP x / VOLUME + / VOLUME – / DIVIDE / A-B
/
DPC (ON/OFF) / VOICE UP (ON/OFF) /
DIRECTNT (ON/OFF) / HOLD
DIRECTNT (ON/OFF) / HOLD
3. Language test
•
Check the language and select the language. (Default language
is Japanese.)
is Japanese.)
•
Press VOLUME + button for English (ENG).
•
Press A-B
button for Japanese (JPN).
4. Loop Back test
Execute the DSP LOOP BACK.
5. Beep test
•
Beep sound of 1.3 kHz or 2 kHz is output.
•
Press the Nx key to start outputting and press the x button
to stop.
to stop.
6. LCD Cont test
•
Adjust the LCD contrast.
Default value is 07.
Default value is 07.
•
Adjust the LCD contrast using the > / . key.
7. RTC Int test
•
Perform the self test of the RTC..
8. Battery test
•
The detected A/D value of the battery remaining power is
checked.
checked.
Selecting items.
setting by the
button
F/W version of
CPU (ARM block)
CPU (ARM block)
F/W version of
CPU (DSP block)
CPU (DSP block)
F/W version of
SUB-SPU
SUB-SPU
The checked key is display.
When all checks are completed,
the back-Light turns on for 0.5
seconds
the back-Light turns on for 0.5
seconds
The NAND formatting
(deleting all events)
and the befault settings
of the menus are completed.
(deleting all events)
and the befault settings
of the menus are completed.
Total of 15 keys* are counted.
SECTION 3
TEST MODE
Click on the first or last page to see other ICD-MX20DR9 service manuals if exist.