DOWNLOAD Sony ICD-AX412 / ICD-AX412F Service Manual ↓ Size: 1.36 MB | Pages: 44 in PDF or view online for FREE

4.  Sin test
•  A sine wave output is produced.

 

LCD DISPLAY

B 

ENTER

<SIN>
Please Enter

10

/

<SIN>

•  A sine wave is outputted.
 

Initial Value: Play VOL = 20/fs = 44.1 kHz/Stereo

•  During operation, change the setting by using the following 

key inputs: 

 

[VOL +]: Volume up

 

[VOL –]: Volume down

•  Other operation by the headphone jack insert/extract signal is 

based on the operation of the set.

•  Press the [

x

] button to return to the test mode screen.

5.  Beep test
•  Beep sound of 1.3 kHz is output.

 

LCD DISPLAY

B 

ENTER

<BEEP>
Please Enter

VOL value

[ VOL+ ] : UP

[ VOL

–  

] : DOWN

10

/

<BEEP>

1.3KHz ON

•  When “Beep Test” is entered, a beep sound of 1.3 kHz is out-

putted from the speaker or the headphone jack. (The destina-
tion where the sound is sent to and the output level are based 
on the operation of the set.)

•  Press the [

x

] button to return to the test mode screen.

6.  LCD Contrast test
•  Adjust the LCD contrast.

 

LCD DISPLAY

B 

ENTER

<LCD CONT>
Please Enter

<LCD CONT>

Vol : 32

•  During operation, change the setting by using the following 

key inputs: 

 

[FF]: The contrast value is increased by 1. 

 

 

(Immediately refl ected)

 

[REW]: The contrast value is decreased by 1. 

 

 

(Immediately refl ected)

 

[PLAY]: The current value is written to the eMMC.

 

 

(The default value is updated.)

•  Press the [

x

] button to return to the test mode screen.

7.  LCD Pattern test
•  LCD and LED on/off checks and LCD contrast adjustment are 

performed.

LCD DISPLAY

B 

ENTER

<LCD PATTERN>
Please Enter

88

188

188

,

DXLOCAL

SCAN HL

.>

REC

NEW

c

VOR

/

B

B

b

> 

+

> 

+

> 

+

> 

+

> 

+

EASY-S

LCF

m

STSPLP

FULL

e

u

b

88

188

188

,

DXLOCAL

SCAN HL

.>

REC

NEW

c

VOR

EASY-S

LCF

m

STSPLP

FULL

e

u

/

B

B

b

b

The LED is 

illuminated orange.

The LED is 

illuminated red.

The LED is 

illuminated red.

The LED is 

illuminated red.

The LED is 

illuminated green.

•  Press the [

x

] button to return the test mode screen.

8.  RTC test
•  Perform the self test of the RTC module.

 

LCD DISPLAY

B 

ENTER

<RTC TEST>
Please Enter

<RTC TEST>

Please wait.....

0.9~1.1 sec

<RTC TEST>

OK

•  At power-on, optionally an R/W test on the clock register is set 

and either an interrupt updated by the second or a 1-sec fi xed-
cycle interrupt to the RTC module is set. And it is verifi ed that 
the interrupt signal is produced.

•  If an interrupt occurs in between 0.9 and 1.1 second after the 

interrupt is enabled to the timer on the main side, it is deter-
mined to be OK.

•  If no interrupt occurs after the elapse of 2 seconds, a timeout is 

set and it is determined to be NG.

•  Press the [

x

] button to return to the test mode screen.

9.  BATT A/D
•  The A/D values related to voltage and temperature are ob-

tained.

 

> 

+

LCD DISPLAY

B 

ENTER

<BATT A/D>
Please Enter

AC : 66
BC : 65

2AC : 00
4BC : 00

TEMP : 71

AC     :Voltage of 2 sell

BC     :Voltage of 1 sell for battery

2AC   :Charge X2 amplifier output value

2BC   :Charge X4 amplifier output value

TEMP :Temperature

•  At power-on the relevant A/D value is obtained and indicated.
 

The indicated value is in 8-bit format (2 bits are cut off on the 
LSB side and then the bits are shifted.)

•  The indicated value is continually updated.
•  Press the [

x

] button to return to the test mode screen.

10. ZLOAD test
•  A battery load check is forcedly executed.

 

LCD DISPLAY

B 

ENTER

<ZLOAD>
Please Enter

<ZLOAD>

ZLOAD : ON

•  The OFF state is set at power-on.
 

[FF]:  Each time the key is pressed, ZLOAD_CTL switches 

between ON and OFF.

•  Press the [

x

] button to return to the test mode screen.

11. LOW DET test
•  The H/W low battery level detection signal LOWBATT_

XDET is checked.

 

LCD DISPLAY

B 

ENTER

<LOW DET>
Please Enter

<LOW DET>

LOW DET : OFF

•  This set is normally off.
•  Press the [

x

] button to return to the test mode screen.

12. VBUS test
•  The VBUS signal is checked.

 

LCD DISPLAY

B 

ENTER

<VBUS>
Please Enter

<VBUS>

OFF

OFF : VBUS_XDET=1(H)

ON   : VBUS_XDET=0(L)

•  At power-on, the acquired value of VBUS_XDET is indicated.  

(Constantly updated)

•  Press the [

x

] button to return to the test mode screen.

13. FM test
•  Operation of the FM tuner is checked.

 

LCD DISPLAY

B 

ENTER

<FM TEST>
Please Enter

FM : OK DX
076.00  Lv : 00.50

•  At power-on, optionally the 00h (DeviceID) value of the FM 

IC register is obtained and compared.

 

OK: DeviceID, the acquired value is OK.

 

NG: DeviceID, the acquired value is NG.

•  If OK, a transition to the FM receiving mode is made and the 

receiver sensitivity is indicated.

 

Receiver sensitivity: Register 0 Ah bit [7:0] 

 

 

(Value of RSS [7:0] )

 

Initial value: 80.0 MHz/DX mode

 

[FF]: The receive step value is increased by 1.

 

[REW]: The receive step value is decreased by 1.

 

[PLAY]:  Each time the key is pressed, change of receive 

sensitivity. (DX t LOCAL t DX t......)

•  Press the [

x

] button to return to the test mode screen.

14. Key Count test
•  The count value is indicated for the key slide switch endurance 

test.

 

LCD DISPLAY

B 

ENTER

<KEY COUNT>
Please Enter

<KEY COUNT>

00000

•  The count value is increased by 1 each time the following sig-

nal change is detected after power-on. The type of a key slide 
switch pressed is not discriminated.

•  All buttons (Also the production of the WakeUP signal is 

checked.)

•  Operate all the slide switches from ON to OFF and then OFF 

to ON.

•  Card insertion signal (Plus 1 only when the card is inserted.)
•  HP/MIC jack detection signal (Plus 1 only when the jack is 

inserted.)

 

Initial value: 00000

 

Upper limit value: 99999

•  If a key is pressed when the counter arrives at the upper limit 

of 99999, it is get back to 00000 and continues the count-up 
operation.

•  Press the [

x

] button to return to the test mode screen.

15. Sleep test
•  A transition to the sleep state is made for measurement of the 

standby current.

 

LCD DISPLAY

B 

ENTER

<SLEEP>
Please Enter

B 

ENTER

SET UP

<SLEEP>

SLEEP : NORMAL

•  A transition to SLEEP state selection is made after power-on.
 

[PLAY]:  The mode is determined. A transition to SLEEP is 

made.

•  The transition from this mode to other mode is inhibited.
•  To exit this mode, disconnect power (unplug the battery.)
•  When the WakeUP signal is detected, the system is rebooted.

16. BATT Lift test
•  A result of measurement made through the battery life mea-

surement F/W is indicated on the LCD.

•  It is impossible to check this in service because the measure-

ment FW is required.

17. CHG LOG test
•  A log for charging held in the SRAM is copied to the eMMC.

 

LCD DISPLAY

B 

ENTER

<CHG LOG>
Please Enter

<CHG LOG>

Success

•  After power-on, a log for charging is copied to the eMMC.
•  An OK/NG result is displayed.
•  Press the [

x

] button to return to the test mode screen.

18. MENU INIT lnit
•  The menu setting is reset to the factory setting.

 

LCD DISPLAY

B 

ENTER

<MENU INIT>
Please Enter

<MENU INIT>

Formatting...

Formatting...

<MENU INIT>

Succes

•  A transition to the initialization wait state is made after MENU 

INIT.

 

[PLAY]: The mode is determined.

 

 

The initialization is executed.

•  An OK/NG result is displayed.
•  Press the [

x

] button to return to the test mode screen.