Sony ICD-AX412 / ICD-AX412F Service Manual ▷ View online
ICD-AX412/AX412F
5
1-2. CASE FRONT ASSY, SPEAKER (SP101)
1 two screws
2 screw
red
black
qa Remove the two solders.
qs speaker (SP101)
3 claw
4 claw
7 claw
5 claw
6 claw
8 two claws
9 case front assy
case front assy
0 two tapping screws
(B 2.0)
ICD-AX412/AX412F
6
1-3. COMPLETE MAIN BOARD
1-4. LIQUID CRYSTAL DISPLAY PANEL (LCD101), MAIN BOARD
7
Remove the two solders.
9
Remove the two solders.
3
Remove the solder.
1
Remove the solder.
2
5
liquid crystal display panel
(LCD101)
qa
MAIN board
6
holder (LCD)
4
connector
8
electret condenser microphone
(MIC102)
0
electret condenser microphone
(MIC101)
blue
claw
claw
blue
white
white
1 screw
2
Remove the two solders.
case (rear) assy
3
COMPLETE MAIN board
ICD-AX412/AX412F
7
SECTION 2
TEST MODE
[Test Mode]
The following checks can be implemented using the Test Mode.
The following checks can be implemented using the Test Mode.
How to Enter the Test Mode
1. Turn the power on. (by inserting batteries)
2. Slide for HOLD to the [HOLD/POWER] switch while press-
1. Turn the power on. (by inserting batteries)
2. Slide for HOLD to the [HOLD/POWER] switch while press-
ing the [VOL –] button and [x] button at the same time.
How to Exit the Test Mode
Exit the test mode by turning OFF the power. (by removing the
batteries)
Exit the test mode by turning OFF the power. (by removing the
batteries)
Operation of the Test Mode
Select the desired item by using the [
Select the desired item by using the [
>
]/[
.
] button, and press
the [
N
/ ENT] button to set the selection.
.
>
Pressing the [VOL-] and
[x] button at the same time.
Center to the
[HOLD/POWER ON/OFF]switch.
Hold to the
[HOLD/POWER ON/OFF]switch.
Release the [VOL-] and
[x] button at the same time.
SERVICE MODE start
MENU display
START
After turn on power
stop or sleep condition
(NORMAL MODE)
END
TEST MODE
Turn off the power
(Remove the batteries)
VERSION
<SERVICE MENU>
KEY CHECK
J
j
SIN
LCD CONT
AUDIO LOOP
BEEP
LCD PATTERN
RTC TEST
ZLOAD
VBUS
BATT A/D
LOW DET
FM TEST
KEY COUNT
BATT LIFE
MENU INIT
SLEEP
CHG LOG
<SERVICE MENU>
ICD-AX412/AX412F
8
1. Version test
• Version of the respective modules are verifi ed.
• Version of the respective modules are verifi ed.
<VERSION>
LCD DISPLAY
Please Eenter
B
ENTER
>
+
ICD-AX412/U
Model Name
Destination
FW Version
Initial Ward
Charge:
C0(Without)/C1(With)
M0(Without)/M1(With)
R0(Without)/R1(With)
Memory Slot:
FM(AM) Radio:
eMMC Marker Code
eMMC Capacity
IPL2 Version
CPU Version
MAINFW : 1.00.00
L : US C1M1R0
eMMC 15 02GB
eMMC 15 02GB
>
+
>
+
IPL2FW:0.08.10
LSI 4252
LSI 4252
• Press the [
x
] button to return to the test mode screen.
2. Key Check test
• Perform the key check by pressing the keys.
• Perform the key check by pressing the keys.
LCD DISPLAY
B
ENTER
<KEY CHECK>
Please Enter
Please Enter
22
/
<KEY CHECK>
21
/
<KEY CHECK>
KEY : ERASE
The number of keys and slide
switches that are not pressed
after the transition to KEY
CHECK is indicated.
switches that are not pressed
after the transition to KEY
CHECK is indicated.
The last key that has been pressed
is indicated.
is indicated.
The counter is decreased by 1 since
the ERASE key is pressed for the
first time. Thereafter , it will not be
decreased even when the ERASE key
is pressed.
Where 22 is counted down to 0 by
pressing of other keys. The setting is
formatted to the factory setting.
the ERASE key is pressed for the
first time. Thereafter , it will not be
decreased even when the ERASE key
is pressed.
Where 22 is counted down to 0 by
pressing of other keys. The setting is
formatted to the factory setting.
• [
x
]/[–
.
]/[
>
+]/[
N
ENTER]/[
z
]/[ A-B]/
[ERASE]/[VOL –]/[VOL +]/[DISP/MENU]/
[FOLDER]/[T-MARK]/[SPEED +]/[SPEED –]/
[DPC (SPECIAL CTRL) ON/OFF]/[HOLD ON/OFF]/
[POWER ON/OFF]/[NOISE CUT ON/OFF]
• Key inputs may be done in any desired order.
When a key input is confi rmed, the name of the key and the
number of undetected keys are indicated.
number of undetected keys are indicated.
• Once all the key inputs are confi rmed, “ACCESS” is displayed
starting initialization. After the initialization has been complet-
ed, the system is rebooted. (The POWER ON state is held.)
ed, the system is rebooted. (The POWER ON state is held.)
• The status is held with the message “ERROR” displayed. (The
system is not rebooted.)
• The transition from this mode to other mode is inhibited.
• To exit this mode, disconnect power (unplug the battery).
• To exit this mode, disconnect power (unplug the battery).
3. Audio Loop test
• Execute the AUDIO LOOP BACK.
• Execute the AUDIO LOOP BACK.
LCD DISPLAY
B
ENTER
<AUDIO LOOP>
Please Enter
Please Enter
AGC : ON
AGC
00:MIC IN
01:AUDIO IN
H
VOR Level
VOR value
External microphone:
Internal microphone:
VOR:00000000
10
/00
M
L
• The Audio Loop Back operation is executed.
Initial Value: Play VOL = 20/fs = 44.1 kHz/Stereo
Microphone Sensitivity: H
External microphone: MIC IN
• When the set is operating, the recording level for VOR is con-
stantly acquired and indicated.
(The level is sampled and held at intervals of 1 second.)
The red LED illuminates when the level is greater than the
VOR set value.
VOR set value.
• During operation, change the setting by using the following
key inputs:
[VOL +]: Volume up
[VOL –]: Volume down
[REC]: Change microphone sencitivity
(M
t L t H t.......)
[PLAY]: External microphone sencitivity
(MIC IN t AUDIO IN t MIC IN t.......)
[REW]: ALC operation (ONtOFFtONt.......)
• Other operation by the external microphone jack and head-
phone jack insert/extract signals is based on the operation of
the set.
the set.
• Press the [
x
] button to return to the test mode screen.
Click on the first or last page to see other ICD-AX412 / ICD-AX412F service manuals if exist.