Sony HT-ST3 Service Manual ▷ View online
HT-ST3
17
9 bluetooth module
(BT1)
bluetooth module
(BT1)
(BT1)
bluetooth module
(BT1)
(BT1)
Terminal face
is below side.
is below side.
8 BT escutcheon
6 flexible flat cable (14 core)
(FFC4)
flexible flat cable (14 core)
(FFC4)
(FFC4)
flexible flat cable
(14 core)
(14 core)
3 connector
(CN786)
5
Remove the bluetooth module block
in the direction of an arrow.
1 core cushion
core cushion
2 saranet cushion
:LUHVHWWLQJ
:LUHVHWWLQJ
saranet cushion
CONNECT board
terminal face
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
flexible flat cable
colored line
connector
4 screw
(BVTP3
u 8)
4 screw (BVTP3 u 8)
7 screw (BVTP2.6)
2-17. BLUETOOTH MODULE (BT1)
HT-ST3
18
2-18. NFC MODULE (NFC1)
2 connector
(CN802)
6 flexible flat cable
(8
core)
(FFC6)
flexible flat
cable (8 core)
(FFC6)
cable (8 core)
(FFC6)
– Front panel block bottom rear view –
:ire VettinJ
NFC module (NFC1) VettinJ
1 saranet cushion
saranet cushion
guide line
5 double adhesive
tape
(NFC)
3 two screws
(BVTP2.6)
4 NFC escutcheon block
7 NFC module
(NFC1)
NFC module (NFC1)
NFC module (NFC1) Terminal face
is below side.
Terminal face is below side.
HT-ST3
19
SECTION 3
TEST MODE
1. TEST MODES OTHER THAN THE TEST MODE MENU
These are executable test mode even if not entering the test mode
menu.
These are executable test mode even if not entering the test mode
menu.
1-1. Cold Reset
It can initialize various backup information.
It can initialize various backup information.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the three buttons of the [INPUT], [VOLUME –] and
[
?/1
] simultaneously.
3. The message “RESET” is displayed on the fl uorescent indica-
tor tube, then turn the power off.
2. TEST MODES IN THE TEST MODE MENU
These are the test modes done in the test mode menu.
These are the test modes done in the test mode menu.
Setting method of the test mode menu:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the two buttons of the [INPUT] and [VOLUME +] si-
multaneously for fi ve seconds.
3. The message “PANEL” blinks on the fl uorescent indicator
tube and enter the test mode menu.
Releasing method of the test mode menu:
Press the [
Press the [
?/1
] button to release the test mode menu.
2-1. Panel Test Mode
It can confi rm the lighting of fl uorescent indicator tube and LEDs,
operation of buttons, display of model name, destination and soft-
ware version.
It can confi rm the lighting of fl uorescent indicator tube and LEDs,
operation of buttons, display of model name, destination and soft-
ware version.
Procedure:
1. Enter the test mode menu.
1. Enter the test mode menu.
(Refer to “Setting method of the test mode menu”)
2. In the state of blinking the “PANEL” on the fl uorescent indica-
tor tube, press the [INPUT] button.
3. All segments in the fl uorescent indicator tube and all LEDs are
lighted up.
4. When pressing the [VOLUME +] button, the display on the
fl uorescent indicator tube repeatedly changes in order from all
lighting
lighting
→ pattern 1 (power indicator LED (white color) is
lighted up)
→ pattern 2 (Bluetooth indicator LED (blue color)
is lighted up).
All ligting
Pattern 1
Pattern 2
5. In the state of step 4, press the [VOLUME –] button and “K 0”
is displayed on the fl uorescent indicator tube.
Each time a button is pressed, “K 0” value increases. However,
once a button is pressed, it is no longer taken into account.
once a button is pressed, it is no longer taken into account.
When pressing the all buttons, “OK” and “K 5” are alternately
displayed on the fl uorescent indicator tube.
displayed on the fl uorescent indicator tube.
HT-ST3
20
6. In the state of step 4, press the [INPUT] button and model
name “HT-ST3” is displayed on the fl uorescent indicator tube.
Each time the [VOLUME +] button is pressed, the display
changes from destination
changes from destination
→ MC (-com) version → SY (sys-
tem) version
→ UI version → TA (AMP) version → DS (DSP)
version
→ BT (Bluetooth) version → NF (NFC) version →
HD (HDMI) version,
→ CE (CEC) version → PF (platform)
version in this order, and returns to the model name display.
NF version
CE version
Model name
Destination
MC version
SY version
PF version
UI version
TA version
HD version
BT version
DS version
(Displayed values in the above fi gure are example)
7. When [INPUT] button is pressed while the each version is dis-
played on the fl uorescent indicator tube, year, month and day
of the software creation is displayed on the fl uorescent indica-
tor tube.
of the software creation is displayed on the fl uorescent indica-
tor tube.
(Displayed values in the above fi gure are example)
When [INPUT] button is pressed again, the display returns to
the each version display.
the each version display.
Releasing method:
Press the [
Press the [
?/1
] button to release the test mode menu.
(When the “K 0” to “K 4” is displayed on the fl uorescent indicator
tube, press the [
tube, press the [
?/1
] button on the remote commander to release
the test mode menu)
2-2. Model Name Display Mode
It can display the model name.
It can display the model name.
Procedure:
1. Enter the test mode menu.
1. Enter the test mode menu.
(Refer to “Setting method of the test mode menu” on page 19)
2. Press the [VOLUME +]/[VOLUME –] buttons to select the
“HT-ST3”.
2-3. Destination Display Mode
It can display the destination.
It can display the destination.
Procedure:
1. Enter the test mode menu.
1. Enter the test mode menu.
(Refer to “Setting method of the test mode menu” on page 19)
2. Press the [VOLUME +]/[VOLUME –] buttons to select the
“CE2”.
2-4. MC Version Display Mode
It can display the MC (
It can display the MC (
-com) version.
Procedure:
1. Enter the test menu.
1. Enter the test menu.
(Refer to “Setting method of the test mode menu” on page 19)
2. Press the [VOLUME +]/[VOLUME –] buttons to select the
“MC.X.XXX” (X.XXX: MC (
-com) version).
(Displayed values in the above fi gure are example)
2-5. Serial Flash Version Display Mode
It can display the SF (serial fl ash) version.
It can display the SF (serial fl ash) version.
Procedure:
1. Enter the test menu.
1. Enter the test menu.
(Refer to “Setting method of the test mode menu” on page 19)
2. Press the [VOLUME +]/[VOLUME –] buttons to select the
“SF.X.XXX” (X.XXX: SF (serial fl ash) version).
(Displayed values in the above fi gure are example)
Click on the first or last page to see other HT-ST3 service manuals if exist.