DOWNLOAD Sony HT-RT5 Service Manual ↓ Size: 9.96 MB | Pages: 64 in PDF or view online for FREE

NOTE  OF  REPLACING  THE  IC6001  AND  IC6004  ON  
THE  BAR-AMP  BOARD  OR  THE  BAR-AMP  BOARD
When IC6001 and IC6004 on the BAR-AMP board or complete 
BAR-AMP board are replaced, it is necessary to spread the com-
pound between the BAR-AMP board and the heat sink.
Spread the compound referring to the fi gure below.

NOTE  OF  REPLACING  THE  MB-1414  BOARD  OR  
CARD  WLAN/BT  COMBO
When the MB-1414 board or card WLAN/BT combo is replaced, 
you must perform the following item.

When replacing the MB-1414 board:
•  NETWORK INFORMATION WRITING AND CHECKING 

OF NETWORK/NFC OPERATION (refer to this page)

• 

NOTICE OF MAC ADDRESS CHANGE TO CUSTOMERS 
(refer to page 7)

•  NOTES ON THE WIRELESS CONNECTION (LINK) AF-

TER REPAIRS ARE COMPLETE (refer to page 7)

When replacing the card WLAN/BT combo:
•  NETWORK INFORMATION WRITING AND CHECKING 

OF NETWORK/NFC OPERATION (refer to this page)

• 

NOTICE OF MAC ADDRESS CHANGE TO CUSTOMERS 
(refer to page 7)

NETWORK  INFORMATION  WRITING  AND  CHECKING  
OF  NETWORK/NFC  OPERATION
When the MB-1414 board or card WLAN/BT combo are replaced, 
execute the below BD service mode, and check the operation of 
wireless/wired LAN and NFC.

Procedure:
1.  Connect this unit with TV monitor.
2.  Press the [

@

/1

] button to turn the power on.

3.  Press button in order of the [

x

] → [DISPLAY] → [

X

] → [

V] 

on the remote commander.

 

(Make the interval when each button is pressed within one sec-
ond)

4.  Enter the BD service mode. The OSD menu on TV monitor 

can be operated by remote commander.

5. Press the [

v] button on the remote commander to select 

“Diag”, and press the [ ] button on the remote commander.

6. Press 

the 

[

b] button on the remote commander to select “Wire-

less LAN Test”. (Screen 1)

7.  Press the [

v] button on the remote commander to select “[5] 

Write P2P address to Registry”.

8.  Press the [ ] button on the remote commander, wait until the 

display show “Status: Write Successful!” (Screen 2).

9.  Press the [BACK] button on the remote commander to return 

to category select screen, and press the [

b] button on the re-

mote commander to select “Bluetooth Device Test”. (Screen 3)

10. Press the [ ] button on the remote commander to select “(1) 

Bluetooth Enable”.

11. Press the [ ] button on the remote commander, wait until the 

display show “Status: Bluetooth Enable Successful!” (Screen 
4).

12. Press the [

v] button on the remote commander to select “(3) 

Write Bluetooth device address to Registry”.

13. Press the [ ] button on the remote commander, wait until the 

display show “Status: Write Successful!” (Screen 5).

14. Press the [

@

/1

] button to turn the power off.

 Diag

 Diag
Category:            Wireless LAN Test

 Diag

 Diag
Category:            Bluetooth Device Test

– Continued on next page –

Necessary Equipment:
• 

Access point supporting WPS

Procedure:
1.  Connect this unit with TV monitor.
2.  Press the [

@

/1

] button to turn the power on.

3.  Press the [HOME] button on the remote commander, display 

the home screen.

4.  Press the [

V]/[v] buttons on the remote commander to select 

the “Setup”, and press the [ ] button on the remote command-
er.

5.  Press the [

V]/[v] buttons on the remote commander to select 

the “Network Settings”, and press the [ ] button on the remote 
commander.

6.  Press the [

V]/[v] buttons on the remote commander to select 

the “Internet Settings”, and press the [ ] button on the remote 
commander.

7.  Press the [

V]/[v] buttons on the remote commander to select 

the “Wireless Setup(built-in)”, and press the [

b] button on the 

remote commander.

8.  Press the [

V]/[v] buttons on the remote commander to select 

the “Wi-Fi Protected Setup (WPS)”, and press the [

b] button 

on the remote commander.

9.  The “Start” screen is display, and press the [WPS] key on the 

access point.

10. Press the [

b] button on the remote commander, setup is start.

11. The message “Next, check the network connection” is dis-

played, and when wireless LAN connection is completed, 
“Wireless Connection: OK” and “Internet Access: OK” is dis-
played.

Note: Refer to the instruction manual about details of the setting method.

Necessary Equipment:
• Router
• 

Network LAN cable

Procedure:
1.  Connect this unit with TV monitor.
2.  Connect the unit to the router with the network LAN cable.
3.  Press the [

@

/1

] button to turn the power on.

4.  Press the [HOME] button on the remote commander, display 

the home screen.

5.  Press the [

V]/[v] buttons on the remote commander to select 

the “Setup”, and press the [ ] button on the remote command-
er.

6.  Press the [

V]/[v] buttons on the remote commander to select 

the “Network Settings”, and press the [ ] button on the remote 
commander.

7.  Press the [

V]/[v] buttons on the remote commander to select 

the “Internet Settings”, and press the [ ] button on the remote 
commander.

8.  Press the [

V]/[v] buttons on the remote commander to select 

the “Wired Setup”, and press the [

b] button on the remote 

commander.

9.  Press the [

V]/[v] buttons on the remote commander to select 

the “Auto”, and press the [

b] button on the remote command-

er.

10. The “The network will be confi gured with the following set-

tings” screen is display, and press the [

b] button on the remote 

commander.

11. Press the [

V]/[v] buttons on the remote commander to select 

the “Save & Connect”, and press the [ ] button on the remote 
commander.

12.  When wired LAN connection is completed, “Physical Connec-

tion: OK” and “Internet Access: OK” is displayed.

Note: Refer to the instruction manual about details of the setting method.

Necessary Equipment:
Smartphones, tablets, or music players with the NFC function 
built-in
(OS: Android™ 2.3.3 or later, excluding Android 3.x)

Procedure:
1.  Press the [

@

/1

] button to turn the power on.

2.  Touch the N mark of the Bar Speaker with the Bluetooth de-

vice.

Bluetooth indicator (blue)

3.  Make sure that the indicator (blue) of the Bar Speaker lights 

up. (This indicates that a connection has been established)

4.  Start playback of an audio source on the Bluetooth device.

Note: After checking of NFC operation, be sure to delete the pairing infor-

mation before returning this unit to the customer.

5. Factory initialize
It returns all settings to the initial state of factory shipment.

Note 1: Disconnect the following connections when you use this mode.
 

   

 USB

 

   

 LAN

 

   

 HDMI IN 1

 

   

 HDMI IN 2

 

   

 HDMI IN 3

Note 2: The operation in this mode must use a remote commander and TV 

monitor.

Procedure:
1.  Connect this unit with TV monitor.
2.  Press the [

?/1

] button to turn the power on. 

3.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

4.  Press the [

V]/[v] buttons on the remote commander to select 

the “Setup”, and press the [ ] button on the remote command-
er.

5.  Press the [

V]/[v] buttons on the remote commander to select 

the “Resetting”, and press the [ ] button on the remote com-
mander.

Setup

Resetting

Easy Network Settings

Easy Setup

Input Skip Setting

– Continued on next page –

6.  Select “Reset to Factory Default Settings”, and press the [

] 

button on the remote commander.

Setup

Reset to Factory Default Settings

Restor each setting to the factory setting.

Initialize Personal Information

7. Press 

the 

[

V]/[v] buttons on the remote commander to select 

the “All Settings”, and press the [ ] button on the remote com-
mander.

Reset to Factory Default Settings

Audio Settings
Bluetooth Settings
System Settings
Input Skip Settings
Network Settings
All Settings

8. Press 

the 

[

B]/[b] buttons on the remote commander to select 

the “Start”, and press the [ ] button on the remote commander.

All Settings

Restore all settings to the factory default
settings. The system will turn off after
reset.

Start

Cancel

9.  Turn the power off automatically, and initialization ends.

NOTICE  OF  MAC  ADDRESS  CHANGE  TO  CUSTOM-
ERS
When the complete MB-1414 board or card WLAN/BT combo is 
replaced, the MAC address has been changed.
Print the following explanations, and pass it to the customer with 
the repaired unit when you return the customer repaired unit.

Note of the MAC address change:
The MAC address of this unit was changed along with this repair.
Please set it again if you are using the MAC address fi ltering function 
of access point device of connection destination.
MAC address can be confi rmed from the settings menu screen of this 
unit. Please refer to the “Settings and Adjustment” of Operating In-
structions for details.

NOTES  ON  THE  WIRELESS  CONNECTION (LINK)  AF-
TER   REPAIRS  ARE  COMPLETE
When the following replacing repair is performed, the link of the 
Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and Surround 
speaker (SA-SLRT5/SRRT5) is cut.
Return the Bar speaker (SA-RT5), Subwoofer (SA-WRT5) and 
Surround speaker (SA-SLRT5/SRRT5) to the customer after per-
forming the link according to the following procedure.

Parts in which the LINK will be disconnected due to replacement:
• 

Complete MB-1414 board

Link method:
When you turn on the Bar speaker (SA-RT5), Subwoofer (SA-
WRT5) and Surround speaker (SA-SLRT5/SRRT5), and then au-
tomatically link.
If do not automatically link, there is a possibility that the customer 
is perform the secure link. In that case, perform the following pro-
cedure.

Press SECURE LINK on the rear of 
the subwoofer and the surround 
speakers until the indicator turns 
orange.
Proceed to the next step within a few 
minutes.

Select [Start].
To return to the previous display, 
select [Cancel].

If the message [Cannot set Secure 
Link.] appears, follow the on-screen 
instructions.

Note: If customer had perform a secure link, only the Bar speaker is 

brought in for repair and the complete MB-1414 board is replaced, 
be sure to inform the customer when returning the repaired products 
that the customer must secure link again the Bar speaker, Subwoofer 
and Surround speaker.

 

  (Indicate that the secure link procedure is described in the operating 

instructions)

BOND  FIXATION  OF  ELECTRIC  PARTS
When the following parts are replaced, fi x the parts by using the 
bond (SC608Z2) (Refer to the fi gure below).

Target parts:
• 

Switching regulator (3L408W)

Press 

 (on/standby) to turn off the system. After the indicator 

disappears, disconnect the AC power cord (mains lead) and make 
sure nothing is obstructing the ventilation holes of the system.