Sony HT-CT770 Service Manual ▷ View online
HT-CT770
13
2-10. MAIN BOARD BLOCK-1
• Continued on next page.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
4 connector
(CN1005)
(CN1005)
(See Fig. A, B)
MAIN board
7 connector
(CN3502)
(CN3502)
8 connector
(CN2005)
(CN2005)
2 cover (MAIN PWB)
(See Fig. B)
cover (MAIN PWB)
1 screw
(BVTP3
(BVTP3
u 8)
MAIN board
POWER board
3 Remove the wire from
the coating clip.
(See
Fig.
A)
coating clip
Wire is under the bracket (main).
coating clip
3 Remove the wire from the coating clip.
(See
(See
Fig.
A)
5 flexible flat cable (19 core)
(CN3501)
(CN3501)
6 flexible flat cable (14 core)
(CN2001)
(CN2001)
:LUHsetting
)LJ$!
)LJ%!
Wire is over the bracket (main).
Wire is under the bracket (main).
Arrange the wire, as shown in the
following figure.
Wire is sticking out from the bottom cabinet.
OK
NG
NG
OK
NG
HT-CT770
14
2-11. MAIN BOARD BLOCK-2
2-12. MAIN BOARD
4 connector
(CN3001)
(CN3001)
5 connector
(CN3002)
(CN3002)
1 four screws
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
1 screw
(BVTP3
(BVTP3
u 8)
2 coating clip
3 Remove the MAIN board block
in the direction of the arrow.
6 MAIN board block
1 sheet radiation (T1)
4 MAIN board
IC3001
2 two screws
(BVTP3
(BVTP3
u 8)
3 heatsink (main)
Note: When you install the heatsink (main),
Note: When you install the heatsink (main),
spread the compound referring to “NOTE
OF REPLACING THE IC3001 ON THE
MAIN BOARD AND THE COMPLETE
MAIN BOARD” on servicing notes
(page
4).
HT-CT770
15
2-13. CONNECTION CABLE WITH SPEAKER (L-CH, R-CH) (SPC1, SPC2)
1 acoustic absorbent (B)
2 connection cable with speaker (R-ch)
(SPC2)
(SPC2)
2 connection cable
with speaker (L-ch)
(SPC1)
connection cable with speaker (L-ch)
(SPC1)
(SPC1)
1 acoustic absorbent (B)
acoustic absorbent (B)
ditch
rib
rib
rib
– Top view –
Connection cable with speaker (L-ch) (SPC1) setting
connection cable with speaker (R-ch)
(SPC2)
(SPC2)
acoustic absorbent (B)
– Top view –
Connection cable with speaker (R-ch) (SPC2) setting
rib
rib
rib
ditch
hook
HT-CT770
16
2-14. POWER CORD (AC1)
2-15. POWER BOARD
1 connector
(CN901)
(CN901)
5 Draw out the power cord
from the hole.
6 power cord
(AC1)
(AC1)
2 Remove the cord bushing (FBS001)
in the direction of the arrow.
4 cord bushing (FBS001)
3 claw
1 screw
(BVTT3
(BVTT3
u 6)
1 screw
(BVTT3
(BVTT3
u 6)
1 two screws
(BVTT3
(BVTT3
u 6)
2 Remove the POWER board block
in the direction of the arrow.
4 POWER board
3 cushion (H)
Click on the first or last page to see other HT-CT770 service manuals if exist.