Sony SS-AC5 Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-AC5
SPECIFICATIONS
SPEAKER SYSTEM
9-893-981-01
2014C33-1
©
2014.03
AEP Model
UK Model
Ver. 1.0 2014.03
Speaker system
2-way 4-driver speaker system, Bass reflex
Speaker unit
Woofer: 130 mm (5.25 in), cone type (1)
Tweeter: Main tweeter, 25 mm (1 in), dome type (1)
Assist tweeter, 19 mm (0.75 in), dome type (2)
Tweeter: Main tweeter, 25 mm (1 in), dome type (1)
Assist tweeter, 19 mm (0.75 in), dome type (2)
Rated impedance
6 ohms
Maximum input power 65 watts
Sensitivity
Sensitivity
84 dB (2.83 V, 1 m)
Frequency response
45 Hz - 40,000 Hz
Dimensions (w/h/d)
Approx. 186 × 350 × 295 mm (7
3
/
8
× 13
5
/
8
× 11
5
/
8
in)
Mass
Approx. 7.6 kg (16 lb 11 oz)
Supplied accessories
Operating Instructions (1)
Design and specifications are subject to change without notice.
SS-AC5
2
SECTION 1
SERVICING NOTES
ABOUT HANDLING OF A SPEAKER UNIT (WOOFER)
Do not put the corn side of a speaker unit (woofer) on a fl oor etc.
When placing a corn side, put on a fl oor etc. after making into a
stand the parts supplied to a new speaker unit. (Refer to the fol-
lowing fi gure.)
Do not put the corn side of a speaker unit (woofer) on a fl oor etc.
When placing a corn side, put on a fl oor etc. after making into a
stand the parts supplied to a new speaker unit. (Refer to the fol-
lowing fi gure.)
ABOUT REPAIRING THE BOARD
The mounted parts of this unit that have each board cannot replace
with single. When each board is defective, replace the complete
mounted board.
The mounted parts of this unit that have each board cannot replace
with single. When each board is defective, replace the complete
mounted board.
NOTE THE SPEAKER UNITS REPLACING
Refer to “2. DISASSEMBLY” (page 3 or subsequent) for the re-
placement procedure of each speaker unit.
Refer to “2. DISASSEMBLY” (page 3 or subsequent) for the re-
placement procedure of each speaker unit.
1. Main tweeter (SP3)
1
1
Main tweeter (2.5 cm) is replaced in the form attached to face
plate. When replacing main tweeter (2.5 cm), please replace
for speaker (2.5 cm) assy including face plate.
for speaker (2.5 cm) assy including face plate.
(Assist tweeter of the upper and lower is not included.)
face plate
SPEAKER (2.5 cm) ASSY
main tweeter
(2.5 cm)
(2.5 cm)
2
Packing (C) is not reused. When assist tweeter is removed,
please be sure to replace packing (C).
assist tweeter
SPEAKER (2.5 cm) ASSY
packing (C)
not reused
not reused
assist tweeter
packing (C)
not reused
not reused
2. Assist tweeter (SP1, SP2)
1
1
When replacing assist tweeter (1.9 cm), in order to guarantee
performance, please be sure to replace upper side and lower
side simultaneously.
side simultaneously.
main tweeter
assist tweeter
Note: Be sure to replace upper side and
Note: Be sure to replace upper side and
lower side simultaneously.
assist tweeter
Note: Be sure to replace upper side and
Note: Be sure to replace upper side and
lower side simultaneously.
2
Packing (C) is not reused. When assist tweeter is removed,
please be sure to replace packing (C).
assist tweeter
SPEAKER (2.5 cm) ASSY
assist tweeter
packing (C)
not reused
not reused
packing (C)
not reused
not reused
SS-AC5
3
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. TWEETER
ASSY-1
• Continued on 2-3 (page 4).
SET
2-2. TWEETER ASSY-1
(Page
(Page
3)
2-3. TWEETER ASSY-2
(Page
(Page
4)
2-4. LOUDSPEAKER 1.9 cm
(ASSIST
(ASSIST
TWEETER)
(SP1,
SP2),
SPEAKER (2.5 cm) ASSY
(MAIN TWEETER) (SP3)
(Page
5)
2-7. TW BOARD BLOCK,
WO BOARD BLOCK
(Page
8)
2-5. TERMINAL BOARD
ASSY
ASSY
(TB1)
(Page
6)
2-6. SPEAKER (13 cm)
(WOOFER)
(WOOFER)
(SP4)
(Page
7)
Note: Please remove grille frame assy.
1 six screws (3.5 u 20)
Note: WLJKWHQLQJWRUTXH1P
SS-AC5
4
2-3. TWEETER
ASSY-2
speaker cabinet
1 Pull out the tweeter assy.
Speaker cabinet
concave portion
concave portion
TW board (MT1)
“AT+” wire [orange]
“AT+” wire [orange]
TW board (MT1)
“TW–” wire [yellow/black]
“TW–” wire [yellow/black]
TW board (MT1)
“TW+” wire [yellow]
“TW+” wire [yellow]
loudspeaker 1.9 cm (assist tweeter)
(SP2) “–” wire [black]
(SP2) “–” wire [black]
loudspeaker 1.9 cm
(assist tweeter)
(SP1) “+” wire [gray]
(assist tweeter)
(SP1) “+” wire [gray]
speaker (2.5 cm) assy (main tweeter)
(SP3) “–” terminal
(SP3) “–” terminal
speaker (2.5 cm) assy (main tweeter)
(SP3) “+” terminal
(SP3) “+” terminal
2 terminal [gray]
2 terminal [yellow]
3 packing (A)
packing (A)
screw hole (six places)
-0.5 mm from a speaker cabinet upper surface.
2 terminal
[yellow/
black]
black]
2 terminal [orange]
Note 1: When installing the tweeter assy, after each screw
holes of the tweeter assy and packing (A) are aligned,
attach it to the speaker cabinet.
Note 2: Check not having overflowed a speaker
cabinet
cabinet
upper surface.
Note 3: Check that there is neither a riding raising
to the speaker cabinet concave portion nor
a position gap of screw holes.
Note 4: Check that packing (A) is not turned over.
Note 9: Be careful not to attach a crack to a
speaker cabinet using the terminal of
a
wire.
Note 10: Check that the connection mistake
or insertion of a wire are not imperfect.
Note 11: Insert the terminal straightly.
Note 12: After terminal insertion, should check
Note 12: After terminal insertion, should check
acting as lock of the terminal completely.
4 tweeter assy
Note
5: When installing the tweeter assy,
be careful not to put wires.
Note
6: Be careful not to attach a crack to
the edge of a speaker cabinet.
Note
7: Do not touch the convex part
(three places) of a tweeter assy.
Note
8: Check that packing (A) has not
overflowed from a upper surface.
:LUHVHWWLQJ
–
8SSHUYLHZ–
Note 13: Check that the caulking
portion of a terminal is
inside suitable (speaker side).
terminal
&DXWLRQVZKHQLQVWDOOLQJWKHSDFNLQJ$
convex part
(three places)
(three places)
TW board (MT1)
“AT–” wire [gray]
“AT–” wire [gray]
Note 13: Check that the caulking
portion of a terminal is
inside suitable (speaker side).
terminal