Sony HCD-SHAKE33 / HCD-SHAKE44 / HCD-SHAKE55 / HCD-SHAKE66 / HCD-SHAKE77 / HCD-SHAKE88 Service Manual ▷ View online
HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
5
NOTE OF REPLACING THE IC001, IC002, IC105, IC106
AND IC302 (SHAKE44/SHAKE66/SHAKE88) ON THE
AND IC302 (SHAKE44/SHAKE66/SHAKE88) ON THE
MOTHERBOARD BOARD
IC001, IC002, IC105, IC106 and IC302 (SHAKE44/SHAKE66/
SHAKE88) on the MOTHERBOARD board cannot exchange
with single. When these parts on the MOTHERBOARD board are
damaged, exchange the entire mounted board.
IC001, IC002, IC105, IC106 and IC302 (SHAKE44/SHAKE66/
SHAKE88) on the MOTHERBOARD board cannot exchange
with single. When these parts on the MOTHERBOARD board are
damaged, exchange the entire mounted board.
NOTE OF REPLACEMENT OF THE MS-476 BOARD
When the MS-476 board is defective, exchange the entire
LOADING COMPLETE ASSY (T).
When the MS-476 board is defective, exchange the entire
LOADING COMPLETE ASSY (T).
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press
1. Press
[
\/1
] button to turn the power on.
2. Press the [CD] (SHAKE33/SHAKE55/SHAKE77) / [DVD/
CD] (SHAKE44/SHAKE66/SHAKE88)] button to select CD/
DVD function.
DVD function.
3. Press the [
x
] button and [
/+] button simultaneously and
hold down for around 5 seconds.
4. The message “UNLOCKED” is displayed and the disc tray is
unlocked.
Note: When
“
LOCKED
”
is displayed, the slot lock is not released by
turning power on/off with the
[
\/1
]
button.
NOTE OF DISASSEMBLE THE CASE, OVERALL
To disassemble the CASE, OVERALL, hexagon key is required to
unscrew the SCREW, TAPPING (HEX).
To disassemble the CASE, OVERALL, hexagon key is required to
unscrew the SCREW, TAPPING (HEX).
NOTE OF REPLACING MOTHERBOARD BOARD OR
BLUETOOTH MODULE OR RC-S801/A (WW) BOARD
When the MOTHERBOARD board or BLUETOOTH module or
RC-S801/A (WW) board are replaced, please execute the below
service mode.
BLUETOOTH MODULE OR RC-S801/A (WW) BOARD
When the MOTHERBOARD board or BLUETOOTH module or
RC-S801/A (WW) board are replaced, please execute the below
service mode.
Pairing this system with a
Bluetooth device
1. Press the [
\
/1
] button to turn the power on.
2. Place the Bluetooth device within 1 meter (3 feet) from the
system.
3. Press BLUETOOTH on the unit to select Bluetooth function.
“BLUETOOTH” appears in the display panel.
4. Hold down BLUETOOTH on the unit for 2 seconds or more.
“PAIRING”
“PAIRING”
fl ashes in the display panel.
5. Perform the pairing procedure on the Bluetooth device.
6. Select the model number of the unit on the display of the
6. Select the model number of the unit on the display of the
Bluetooth device.
For example, select “SONY:SHAKE-88D” (or SHAKE-33/
SHAKE-44D/SHAKE-55/SHAKE-66D/SHAKE-77). If
passkey is required on the Bluetooth device, enter “0000”.
SHAKE-44D/SHAKE-55/SHAKE-66D/SHAKE-77). If
passkey is required on the Bluetooth device, enter “0000”.
7. Perform
the
Bluetooth connection on the Bluetooth device.
8. When pairing is completed and the Bluetooth connection is
established, the Bluetooth device name appears in the display
panel.
panel.
9. To cancel pairing operation, hold down BLUETOOTH on the
unit for 2 seconds or more until “BLUETOOTH” appears in
the display panel.
the display panel.
Connecting with a smartphone by one touch (NFC)
Note: The operation in this mode must use a NFC-compatible smartphone
(Smartphones with a built-in NFC function [OS: Android 2.3.3 or
later, excluding Android 3.x])
later, excluding Android 3.x])
1. Press the [
\
/1
] button to turn the power on.
2. Download and install the app “NFC Easy Connect”.
Download the free Android app from Google Play by searching
for “NFC Easy Connect”.
for “NFC Easy Connect”.
3. Start the app “NFC Easy Connect” on the smartphone.
Make sure that the application screen is displayed.
4. Touch the smartphone to the N-Mark on the system until the
smartphone vibrates.
Complete the connection by following the instructions
displayed on the smartphone.
5. When pairing is completed and the Bluetooth connection is
established, the Bluetooth device name appears in the display
panel.
panel.
hexagon key
hexagon key
Ver. 1.4
HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
6
Playing music from a
Bluetooth device
For a Bluetooth device
1. Press the [
1. Press the [
\
/1
] button to turn the power on.
2. Press BLUETOOTH on the unit to select Bluetooth function.
“BLUETOOTH” appears in the display panel.
3. Establish connection with the Bluetooth device.
Press BLUETOOTH on the unit to connect to the last
connected Bluetooth device.
connected Bluetooth device.
Perform
the
Bluetooth connection from the Bluetooth device if
the device is not connected.
Once the connection is established, the Bluetooth device name
appears in the display panel.
appears in the display panel.
4. Press
N
.
Depending on the Bluetooth device,
– you may have to press N twice.
– you may need to start playback of an audio source on the
Bluetooth device.
Bluetooth device.
For an NFC-compatible smartphone
1. Press the [
1. Press the [
\
/1
] button to turn the power on.
Touch the smartphone to the N-Mark on the system to establish
the Bluetooth connection.
the Bluetooth connection.
Start playback of an audio source on the smartphone. For
details on playback, refer to the operating instructions of your
smartphone.
smartphone.
To disconnect the Bluetooth device
For a Bluetooth device
Press BLUETOOTH on the unit.
“BLUETOOTH” appears in the display panel.
For a Bluetooth device
Press BLUETOOTH on the unit.
“BLUETOOTH” appears in the display panel.
For an NFC-compatible smartphone
Touch the smartphone to the N-Mark on the system again.
Touch the smartphone to the N-Mark on the system again.
To erase all the pairing registration information perform
COLD RESET test mode (Refer page 17).
COLD RESET test mode (Refer page 17).
Ver. 1.3
NOTE OF REPLACING THE COMPLETE MOTHERBOARD
BOARD (SHAKE55: US / SHAKE66: MY / SHAKE88: EA)
The COMPLETE MOTHERBOARD BOARD for this unit has
been changed in the midway of production.
When the COMPLETE MOTHERBOARD BOARD is defective,
check the label model number before repair.
Please order the related type of COMPLETE MOTHERBOARD
BOARD in part list.
BOARD (SHAKE55: US / SHAKE66: MY / SHAKE88: EA)
The COMPLETE MOTHERBOARD BOARD for this unit has
been changed in the midway of production.
When the COMPLETE MOTHERBOARD BOARD is defective,
check the label model number before repair.
Please order the related type of COMPLETE MOTHERBOARD
BOARD in part list.
Label Model Number
Type
4-487-772-1[]
Type A
4-487-772-2[]
Type B
4-529-214-1[]
Type C
4-529-214-2[]
Type D
4-529-215-2[]
Type E
4-529-215-3[]
Type F
AC 120V ~ 60Hz 500W
Contains FCC ID: PPQ-WB115C
Contains FCC ID: PPQ-WB115C
R
Label Model Number
HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
7
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note 1: After the case overall is removed, this word is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
2 Insert the clip etc.
3
tray
tray
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
8 cm or more
hole
– Side view –
– Top view –
Note: Push after it inserts it in this hole well.
CD/DVD drive
1 Remove the case, overall.
(Illustration of disassembly is omitted.)
CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION
Switching Regulator Board (Conductor side view) (HCD-SHAKE33/SHAKE44)
In checking the Switching Regulator board, make 3 capacitors discharge of C221, C602 and C618 for eletrical shock prevention.
In checking the Switching Regulator board, make 3 capacitors discharge of C221, C602 and C618 for eletrical shock prevention.
800
:/5 W
800
:/5 W
800
:/5 W
C602
C618
C221
Ver. 1.1
HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
8
Switching Regulator Board (Conductor side view) (HCD-SHAKE55/SHAKE66/SHAKE77/SHAKE88)
In checking the Switching Regulator board, make 3 capacitors discharge of C20, C28 and C18 for eletrical shock prevention.
In checking the Switching Regulator board, make 3 capacitors discharge of C20, C28 and C18 for eletrical shock prevention.
800
:/5 W
C20
C28
C18
800
:/5 W
800
:/5 W
PRECAUTION WHEN INSTALLING A NEW OP UNIT/PRECAUTION BEFORE UNSOLDERING THE STATIC
ELECTRICITY PREVENTION SOLDER BRIDGE (CDM90-DVBU202//M)
ELECTRICITY PREVENTION SOLDER BRIDGE (CDM90-DVBU202//M)
When installing a new OP unit, be sure to connect the fl exible printed circuit board fi rst of all before removing the static electricity
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsoldering after the fl exible printed circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsoldering after the fl exible printed circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)
Ver. 1.1
Click on the first or last page to see other HCD-SHAKE33 / HCD-SHAKE44 / HCD-SHAKE55 / HCD-SHAKE66 / HCD-SHAKE77 / HCD-SHAKE88 service manuals if exist.