DOWNLOAD Sony HCD-RG55 / HCD-RG55S / MHC-RG55 / MHC-RG55S Service Manual ↓ Size: 4.49 MB | Pages: 71 in PDF or view online for FREE

16

base unit

qs

6

two screws (+PTPWH M2.6)

7

two springs (insulator), coil

0

two springs (insulator), coil

2

shild cover

3

screw (+PTPWH M2.6)

5

screw (DIA. 12)

8

two screws (+BVTP 2.6

 

×

 8)

qs

two insulators

4

holder (BU) assy

qa

two insulators

9

two stoppers (BU)

1

screw (+BVTP 2.6

 

×

 8)

qa

 Pull-out the disc tray.

6

two

 screws (+BVTP 2.6 

×

 8)

qs

screw (+PTPWH 2.6

 

×

 8)

qd

tray

4

screw (+BVTP 2.6

 

×

 8)

1

screw 
(+BVTP 2.6

 

×

 8)

qf

screw 
(+BVTP 2.6

 

×

 8)

5

plate

3

CN702 (flat type)

8

CN721(flat type)

0

MOTOR board

qg

SENSOR (CD) board

2

DRIVER board

7

Remove the two solderings of motor.

9

CN722

17

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning the
set to the customer.

Procedure:
1. Press three buttons  x  ,  GROOVE  , and  ?/1  simultaneously.
2. The fluorescent indicator tube displays “COLD RESET” and

the set is reset.

• This mode moves the pickup to the position durable to vibration.

Use this mode when returning the set to the customer after repair.

Procedure:
1. Press  ?/1  button to turn the set ON until “STANDBY”

appears.

2. Press  CD  button and  ?/1  button simultaneously.
3. When you releaset he buttons, a message “LOCK” is displayed

on the fluorescent indicator tube, and the CD ship mode is set.

• This mode resets the set with the preset data kept stored in the

memory. The hot reset mode functions same as if the power cord
is plugged in and out.

Procedure:
1. Press three buttons  x  ,  GAME EQ  , and  DISPLAY

simultaneously.

2. The fluorescent indicator tube becomes blank instantaneously,

and the set is reset.

• This mode can run the CD sled motor freely. Use this mode, for

instance, when cleaning the pickup.

Procedure:
1. Press  ?/1  button to turn the set ON.
2. Select the function “CD”.
3. Press three buttons  x  ,  GAME EQ  , and  OPEN/CLOSE

simultaneously.

4. The CD service mode is selected.
5. With the CD in stop status, press the > key to move the pickup

to outside track, or turn the shuttle knob counter-clockwise to
inside track.

6. To exit from this mode, perform as follows:

1) Move the pickup to the most inside track.
2) Cold reset.

 • Always move the pickup to most inside track when exiting

from this mode. Otherwise, a disc will not be unloaded.

• Do not run the sled motor excessively, otherwise the gear

can be chipped.

• A step of AM channels can be changed over between 9 kHz and

10 kHz.

Procedure:
1. Press  ?/1  button to turn the set ON.
2. Select the function “TUNER”, and press  TUNER/BAND

button to select the BAND “MW”.

3. Press  ?/1  button to turn the set OFF.
4. Press  ENTER  and  ?/1  buttons simultaneously, and the

display of fluorescent indicator tube changes to “AM 9 k STEP”
or “AM 10 k STEP”, and thus the channel step is changed over.

• This mode is used to check the software version, FL tube, LED,

keyboard, headphone and volume.

Procedure:
1. Press three buttons  x  ,  GAME EQ  and  DISC2

simultaneously.

2. LEDs and fluorescent indicator tube are all turned on.
3. When  GAME EQ  and  DISC2  are pressed at the same time,

the key number check mode starts up. In this mode, the key
numbers of each key series are displayed.

4. In the key check mode, the fluorescent indicator tube displays

“KEY 000”. Each time a button is pressed.

5. When  GAME EQ  and  DISC2  are pressed at the same time,

the key count check mode starts up. In this mode, the message
“KEY CNT @@” is displayed on the FL display tube. When
each button is pressed, the key row number is incremented first.
Then the key value is then incremented. However, one the
button is pressed, the key value cannot be counted.

6. When  GAME EQ  and  DISC2  are pressed at the same time,

the headphones check mode starts up. In this mode, the
message “H_P ON” is displayed when the headphones are in-
serted. When the headphones are not inserted, the message “H_P
OFF” is displayed.

7. When  GAME EQ  and  DISC2  are pressed at the same time,

the volume check mode starts up. In this mode, the message
“VOLUME STOP” is displayed on the FL display tube. When
the volume control knob is rotated in the positive (+) direction,
the message “VOLUME UP” is displayed. When the volume
control knob is rotated in the negative (–) direction, the
message “VOLUME DOWN” is displayed.

8. In order to quit the mode, either press  GAME EQ  and  DISC2

at the same time or press the three buttons at the same time as in
step 1.

9. To exit from this mode, cold reset or disconnect the power cord.

18

• This mode is used to check operations of the respective sections

of Amplifier, TUNER, CD and Tape.

Procedure:
1. Press the  ?/1  button to turn on the set.
2. Press the three buttons of  x  ,  GAME EQ  and  DISC 3

simultaneously.

3. A message “TEST MODE” appears on the FL display tube.

• The messages VACS1 to VACS5 are displayed when the VACS

is changed in this mode.

• The number of repeats of TAPE and CD is set to the infinite

number as the default setting.

4. When  MUSIC EQ  button is pressed, GEQ increases to its

maximum and a message “GEQ MAX” appears.

5. When  MUSIC EQ  button is pressed, GEQ decreases to its

minimum and a message “GEQ MIN” appears.

6. When  EFFECT ON/OFF  button is pressed, GEQ is set to flat

and a message “GEQ FLAT” appears.

7. In the test mode, the default-preset channel is called even when

the TUNER is selected and an attempt is made to call the preset
channel that has beeen stored in memory, by operating the
Shuttle knob. (It means that the memory is cleared.)

8. When a tape is inserted in the Deck B and the TAPE B function

is selected, and when the  REC PAUSE/START  buttton is
pressed twice, recording starts.
The VIDEO function is selected automatically as the input
source.

9. Select the desired loop by pressing the  PLAY MODE  button

in the TAPE B function. Insert a test tape AMS-110A or AMS-
RO to Deck A.

10. Press the  SPECTRUM  button to enter the AMS test mode.
11. After a tape is rewound first, the FF AMS is checked, and the

mechanism is shut off after detecting the AMS signal twice.

12. Then the REW AMS is checked and the mechanism is shut off

after detecting the AMS signal twice.

13. When the check is complete, a message of either OK or NG

appears.

14. When the two buttons of  SPECTRUM  and  DISC1  are pressed

at the same time in any function modes, either the “VACS ON”
display to enable the VACS function or the “VACS OFF”
display to disable the VACS function can be selected.

15. When you want to exit this mode, press the  ?/1  button twice.

The cold reset is enforced at the same time.

• If the following operation is performed during the POWER OFF

in the modes other than the POWER SAVE mode (i.e., while the
Demo display shows the watch time).

1. When three buttons of  STOP  ,  GAME EQ  ,  MOVIE EQ  are

pressed at the same time, the model name and destination are
displayed as “GYO AS1A3”.

2. When three buttons of  STOP  ,  GROOVE  are pressed at the

same time, the MC and the GC microprocessor version
numbers are displayed as “V01.02:01.12.24”.

19

This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:

The aging operation stops and display status.

• If no error occurs:

The aging operation continues repeatedly.

1. Operating method of Aging Mode
Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray. Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons  x  ,  GAME EQ  , and

 DISC SKIP EX-CHANGE  simultaneously.

4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [Cold Reset].

2. Aging Mode in CD section
1) Display state
• No error occurs

Display

: Number of aging operations

E ** s ## $$ %%

1 2 3 4 5

*

*

*

*

AGING

*

*

*

*

1

 

**

The error No. 00 indicates the newest error. As the error No. increases, it means the older error.

When you want to retrieve the error history, press the  PLAY MODE  button in the case of mechanism error.

Or press the  REPEAT  button in the case of NO DISC error.

2

 s

M: Mechanism error

D: No disc error

3

 

##

Don’t care

01: FOCUS ERROR

02: GFS ERROR

03: SETUP ERROR

4

 

$$

High order digits only

01: NO DISC judgment without chucking retry

D: Stopped during closing due to problems other than mechanism.

02: NO DISC judgment after chucking retry

E: Stopped during opening due to problems other than mechanism.

C: Stopped during chucking due to problems other than mechanism.

F: Stopped during EX-opening due to problems other than mechanism.

5

 

%%

Emergency related errors (High order digits only)

Status at the time of NO DISC judgment

1: Stopped during chuck-up

(High order digits only)

2: Stopped during chuck-down

1: STOP

3: Time out by EX-OPEN

2: SETUP

5: Time out by EX-CLOSE

3: TOC READ

4: ACCESS

5: PLAY BACK

6: PAUSE

7: MANUAL SEARCH (PLAY)

8: MANUAL SEARCH (PAUSE)

•

When the buttons  x  ,  ENTER  and  DISC 1  are pressed simultaneously, number of time of the mechanism error and the NO DISC error
can be checked.
Display: 

EMC**EDC**

**

: Number of times of error (Maximum three times)

EMC : Mechanism error
EDC : No DISC error

• When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.