Sony HCD-IS10 Service Manual ▷ View online
9
HCD-IS10
Remote control
A
TV
[
/
1
(on/standby)
B
TV button/TV mode indicator
C Z
(eject)
D
SLEEP
E
Number buttons
2) 3)
F
CLEAR
-/--
-/--
3)
G
TONE
H
FUNCTION
I
DVD TOP MENU
J C
/
X
/
x
/
c
,
(ENTER)
3)
K O
RETURN
3)
L .
/
>
PRESET –/+
M
c
/
C
STEP
N m
/
M
/
TUNING –/+
O
REPEAT
P
VOLUME +/–
3)
Q
MUTING
R
AUDIO
2)
S
PICTURE NAVI
T
MOVIE/MUSIC
U
RESOLUTION
V
DIRECT TUNING
W
TUNER MENU
X [
/
1
(on/standby)
Y
DISPLAY
Z
TV INPUT
wj
ENTER
1) 3)
wk
SOUND FIELD
wl
DVD MENU
TOOLS
TOOLS
3)
e;
DISPLAY
TV MENU
3)
ea
H
(play)
2)
es
x
(stop)
ed
X
(pause)
ef
TV CH +/–
2)
eg
SUBTITLE
eh
ANGLE
ej
NIGHT
ek
DIMMER
el
SYSTEM MENU
1)
The ENTER wj button is the same function as the
(ENTER) 0 button.
2)
The 5, H, TV CH +, and AUDIO buttons have
tactile dots. Use the tactile dots as references
when operating the system.
tactile dots. Use the tactile dots as references
when operating the system.
3)
These buttons change to the TV operation buttons
when the remote is in TV mode. The remote is in
TV mode when the TV mode indicator 2 lights
up by pressing the TV button 2.
when the remote is in TV mode. The remote is in
TV mode when the TV mode indicator 2 lights
up by pressing the TV button 2.
With the cover opened.
HCD-IS10
10
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note 1: The process described in
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
SECTION 3
DISASSEMBLY
3-2. COVER (BOTTOM) ASSY
(Page 11)
3-3. OPTICAL PICK-UP BLOCK
(KHM-313CAB)
(Page 11)
(Page 11)
3-6. MAIN BOARD
(Page 13)
3-7. IO BOARD
(Page 13)
3-8. REG BOARD
(Page 14)
3-9. DMB-IVHD BOARD
(Page 14)
3-11. MECHANISM DECK SECTION (CDM86A-DVBU101)
(Page 15)
3-10. FRONT PANEL BLOCK
(Page 15)
3-4. PANEL (SIDE-L/R) ASSY
(Page 12)
3-5. PANEL (TOP) BLOCK, SHIELD PLATE (TOP)
(Page 12)
3-12. MD (86A) ASSY
(Page 16)
3-13. MOTOR (PULLEY) ASSY
(LOADING) (M001)
(Page 16)
(Page 16)
3-14. HOLDER (BU) ASSY
(Page 17)
3-15. LEVER (BU LOCK)
(Page 17)
3-16. CLOSE LEVER
(Page 18)
3-17. LEVER (DIR),
GEAR (IDL-B)
(Page 18)
(Page 18)
3-18. CHASSIS (TOP)
(Page 19)
3-19. LEVER (LOADING-L/R)
(Page 20)
3-20. LEVER (DISC SENSOR)/
(DISC STOP)
(Page 21)
(Page 21)
3-21. GEAR (IDL-C)
(Page 21)
SET
HCD-IS10
11
3-3. OPTICAL PICK-UP BLOCK (KHM-313CAB)
Note:
Follow the disassembly procedure in the numerical order given.
3-2. COVER (BOTTOM) ASSY
1
four screws
(BVTP3
(BVTP3
×
8)
2
cover (bottom) assy
sheet
Note: Please spread a seat under a set
not to injure panel (top) assy.
– bottom view –
1
two screws
(BVTP3
(BVTP3
×
8)
2
cover (chassis)
5
four insulator screws
9
insulator
9
three insulators
3
two claws
6
Lift up the
optical pick-up block.
optical pick-up block.
8
Be sure to bridge here, and then disconnect the
wire (flat type) (24 core).
(optical pick-up block will be destroyed without bridging.)
On the contrary at the installation, connect the
wire (flat type) (24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
wire (flat type) (24 core).
(optical pick-up block will be destroyed without bridging.)
On the contrary at the installation, connect the
wire (flat type) (24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
PRECAUTION WHEN REMOVING GOOD OPTICAL PICK-UP BLOCK
4
Lift up the FFC holder.
7
connector
0
optical pick-up block
(KHM-313CAB)
(KHM-313CAB)
Note: A screw hole of this screw tends to be damaged,
so please be careful about the installation time
and the time of removal.
and the time of removal.
HCD-IS10
12
3-4. PANEL (SIDE-L/R) ASSY
3
screws
(BVTP3
(BVTP3
×
8)
4
panel (side-R) assy
5
screws
(BVTP3
(BVTP3
×
8)
6
panel (side-L) assy
1
three screws
(BVTP3
(BVTP3
×
8)
2
cover (rear) assy
– back view –
3-5. PANEL (TOP) BLOCK, SHIELD PLATE (TOP)
2
screws
(BVTP3
(BVTP3
×
8)
2
screws
(BVTP3
(BVTP3
×
8)
5
three screws
(BVTP3
(BVTP3
×
8)
6
three screws
(BVTP3
(BVTP3
×
8)
4
two screws
(BVTP3
(BVTP3
×
8)
4
two screws
(BVTP3
(BVTP3
×
8)
7
shield plate (top)
1
wire (flat type) (11 core)
(CN108)
(CN108)
3
panel (top) block
– back view –
Click on the first or last page to see other HCD-IS10 service manuals if exist.