Sony HCD-IS10 Service Manual ▷ View online
HCD-IS10
13
3-7. IO BOARD
3-6. MAIN BOARD
qd
four screws
(BVTP3
(BVTP3
×
8)
5
wire (flat type)
(CN102) (9 core: except AEP, UK, Russian models)/
(CN101) (11 core: AEP, UK, Russian models)
(CN102) (9 core: except AEP, UK, Russian models)/
(CN101) (11 core: AEP, UK, Russian models)
6
wire (flat type) (21 core)
(CN103)
(CN103)
1
screw
(BVTP3
(BVTP3
×
8)
2
insulating sheet
(motor)
(motor)
US, Canadian
8
connector (CN107)
9
connector (CN111)
3
two screws
(BVTP3
(BVTP3
×
8)
4
shield plate (side-L)
7
wire (flat type) (19 core)
(CN105)
(CN105)
0
wire (flat type) (9 core)
(CN110)
(CN110)
qs
wire (flat type) (13 core)
(CN106)
(CN106)
qf
MAIN board
qa
wire (flat type) (11 core)
(CN109)
(CN109)
– back view –
1
wire (flat type) (21 core)
(CN103)
(CN103)
3
two screws
(BVTP3
(BVTP3
×
8)
6
five screws
(BVTP3
(BVTP3
×
8)
4
screw
(BVTT3
(BVTT3
×
8)
5
2
screw
(BVTP3
(BVTP3
×
8)
7
back panel (HCD)
8
IO board
– back view –
HCD-IS10
14
3-8. REG BOARD
5
connector (CN702)
8
0
connector (CN710)
9
connector (CN708)
qa
REG board
6
connector (CN111)
7
two screws
(BVTP3
(BVTP3
×
8)
– back view –
1
screw
(BVTP3
(BVTP3
×
8)
2
insulating sheet
(motor)
(motor)
US, Canadian
3
two screws
(BVTP3
(BVTP3
×
8)
4
shield plate (side-L)
3-9. DMB-IVHD BOARD
6
eight screws
(BVTP3
(BVTP3
×
8)
3
connector (CN201)
7
DMB-IVHD board
4
connector (CN105)
5
connector (CN601)
1
wire (flat type) (7 core)
(CN202)
(CN202)
2
wire (flat type) (24 core)
(CN101)
(CN101)
Perform work with this wire (flat type) (24 core) connected, or make a bridge as mentioned above and then disconnect the wire
(flat type) (24 core). (Optical pick-up will be destroyed without bridging.) On the contrary at the installation, connect the wire (flat type)
(24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire. (Refer to DISASSEMBLY 3-2. OPTICAL PICK-UP BLOCK (KHM-313CAB))
(flat type) (24 core). (Optical pick-up will be destroyed without bridging.) On the contrary at the installation, connect the wire (flat type)
(24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire. (Refer to DISASSEMBLY 3-2. OPTICAL PICK-UP BLOCK (KHM-313CAB))
PRECAUTION WHEN REMOVING WIRE (FLAT TYPE) (24 CORE)
– back view –
HCD-IS10
15
3-10. FRONT PANEL BLOCK
1
screw
(BVTP3
(BVTP3
×
8)
3
two screws
(BVTP3
(BVTP3
×
8)
6
three screws
(BVTP3
(BVTP3
×
8)
4
shield plate (side-L)
5
wire (flat type) (11 core)
(CN109)
(CN109)
7
front panel block
2
insulating sheet
(motor)
(motor)
US, Canadian
3-11. MECHANISM DECK SECTION (CDM86A-DVBU101)
3
ql
mechanism deck section
(CDM86A-DVBU101)
(CDM86A-DVBU101)
5
shield plate (side-R)
1
two screws
(BVTP3
(BVTP3
×
8)
8
two screws (BVTP3
×
8)
9
bracket (SYS)
4
two screws
(BVTT2.6
(BVTT2.6
×
6)
2
screw
(BVTP3
(BVTP3
×
8)
7
tuner (FM/AM)
qa
two screws
(BVTP2.6)
(BVTP2.6)
qs
two ground
plates (panel)
plates (panel)
qd
bracket (CDM)
0
system cable
qf
three screws
(BVTP3
(BVTP3
×
8)
qg
shield plate (front)
qh
two screws
(BVTP3
(BVTP3
×
8)
qj
sub chassis (HCD)
qk
screw
(BVTP3
(BVTP3
×
8)
6
wire (flat type)
(9 core: except AEP, UK, Russian models)/
(11 core: AEP, UK, Russian models)
(9 core: except AEP, UK, Russian models)/
(11 core: AEP, UK, Russian models)
HCD-IS10
16
3-12. MD (86A) ASSY
3-13. MOTOR (PULLEY) ASSY (LOADING) (M001)
3
wire (flat type) (24 core)
4
two insulator screws
5
two insulators
5
two insulators
6
optical pick-up block
(KHM-313CAB)
(KHM-313CAB)
4
two insulator screws
1
two claws
2
FFC holder
7
MD (86A) assy
3
Remove two solders.
2
two screws
(B2.6
(B2.6
×
8)
5
MS-214 board
4
motor (pully) assy (loading)
(M001)
(M001)
1
belt (MOT)
Click on the first or last page to see other HCD-IS10 service manuals if exist.