Sony HCD-FX900KW Service Manual ▷ View online
25
HCD-FX900KW
3
1
Remove five solders.
– bottom view –
RELAY board
2
four screws
(+BVTP2.6)
4
connector
(CN710)
(CN710)
5
connector
(CN703)
(CN703)
6
RELAY board
4
5
stocker motor board
3
two screws
(+BVTP2.6)
2
Remove two solders.
6
motor (stocker) assy
(stocker) (M761)
(stocker) (M761)
1
belt (stocker)
3-16. RELAY BOARD
3-17. MOTOR (STOCKER) ASSY (STOCKER)(M761)
26
HCD-FX900KW
1
belt (roller V)
4
ROLLER MOTOR board
2
Remove two solders.
5
motor (roller) assy
(roller)(M781)
3
two screws
(+BVTP2.6)
1
Remove five solders
of rotary encoder.
of rotary encoder.
2
Remove two solders
of motor (M771).
of motor (M771).
MODE MOTOR
board
board
4
MODE MOTOR board
5
belt (mode V)
6
motor (mode) assy
(mode) (M771)
(mode) (M771)
3
two screws
(+BVTP2.6)
3-18. MOTOR (ROLLER) ASSY (ROLLER)(M781)
3-19. MOTOR (MODE) ASSY (MODE)(M771)
27
HCD-FX900KW
3-20. RUBBER ROLLER (SLIDER) ASSY
3-21. TIMING BELT (FRONT/REAR)
qg
sub chassis
qf
screw
(+BVTP2.6
×
8)
8
step screw
qs
step screw
5
step screw
9
tension
spring
(slider 2)
spring
(slider 2)
6
tension spring
(slider 4)
(slider 4)
0
rubber roller
(slider 4) assy
(slider 4) assy
7
rubber roller
(slider 1) assy
(slider 1) assy
qa
rubber roller
(slider 2) assy
(slider 2) assy
qd
rubber roller
(slider 1) assy
(slider 1) assy
3
tension spring
(base slider 5)
(base slider 5)
1
step screw
4
rubber roller
(slider 5) assy
(slider 5) assy
2
rubber roller
(slider S) assy
(slider S) assy
bracket (top) assy
Note: Refer to assembly (Section 4)
2
gear (mode cam)
: Note
: Note
1
screw
(+PTPWH2.6
×
8)
3
slider (mode cam) assy
5
two gears
(center)
(center)
7
two gears (center)
8
timing belt (rear)
9
timing belt (rear)
4
gear
(timing)
(timing)
6
timing belt
(front)
(front)
timing belt
(rear)
(rear)
When install three timing belts,
its pass under each claws.
its pass under each claws.
timing belt
(rear)
(rear)
timing belt (front)
claw
claw
claw
claw
28
HCD-FX900KW
3-22. CAM (GEAR)
3-23. SENSOR BOARD
qf
cam (gear)
: Note
: Note
qs
gear(mode cam)
0
gear (mode C)
:Note
:Note
4
gear (mode 5)
8
gear (mode D)
6
gear (mode 5)
1
screw(+PTPWH2.6
×
8)
7
screw (+PTPWH2.6
×
8)
9
screw
(+PTPWH2.6
×
8)
qa
screw
(+PTPWH2.6
×
8)
3
screw (+PTPWH2.6
×
8)
5
screw (+PTPWH2.6
×
8)
2
pulley
(mode deceleration)
(mode deceleration)
qd
screw
Note: Refer to assembly
(Section 4).
(Section 4).
ql
harness
qd
gear (eject lock)
q;
cam (eject lock)
: Note
qh
two claws
qj
rotary encoder
(S771)
(S771)
qf
gear
(mode B)
(mode B)
w;
screw
(+BVTP2.6
×
8)
qg
screw
(+PWH 2
(+PWH 2
×
6)
wa
SENSOR board
8
shaft
(shutter)
(shutter)
7
compression spring
(shutter)
(shutter)
qs
cam (BU U/D)
qa
screw
(+PTPWH2.6
(+PTPWH2.6
×
8)
3
screw
(+BVTP2.6
(+BVTP2.6
×
8)
1
screw
(+PTPWH2.6
(+PTPWH2.6
×
8)
4
two screws
(+BVTP2.6
(+BVTP2.6
×
8)
2
lever shutter (A)
5
base (shutter) block
6
gear (mode A)
9
screw
(+PTPWH2.6
(+PTPWH2.6
×
8)
qk
claw
Note: Refer to assembly (Section 4).
Click on the first or last page to see other HCD-FX900KW service manuals if exist.