Sony HCD-EC719IP / HCD-EC919IP Service Manual ▷ View online
HCD-EC719iP/EC919iP
9
2-3. POWER CORD (AC1), REAR PANEL BLOCK
5 connector
(XP16)
4 fan connector
(XP14)
7 claw
7 claw
9 rear panel block
8 Remove the rear panel block
in the direction of an arrow.
1 power cord connector
(CN501)
3 power cord
(AC1)
– Rear view –
7 claw
7 claw
(EC919iP)
OK
NG
Note 2: When installing the rear
panel block, check that
jacks are properly secured.
Jacks are fitted to
the surface.
the surface.
Jacks has been
depressed.
depressed.
6 screw
(silver
3
u 8)
6 screw
(silver
3
u 8)
6 screw
(silver
3
u 8)
2
Power cord setting
– Rear view –
Note 1: When installing the power cord (AC1),
check the direction of connector.
HCD-EC719iP/EC919iP
10
2-5. FRONT PANEL BLOCK
2-4. CD DOOR
4 CD door
3 four claws
2 Pull out the disc tray.
– Rear view –
1 Turn the traverse gear in
the direction of an arrow.
bottom side
top side
– Rear view –
4 two claws
4 two claws
5 front panel block
– Rear right view –
3 connector
(XP15)
2 connector
(XP7)
1 connector
(XP19)
Wire setting
Wire from USB board
is upper.
is upper.
Wire from FRONT board
is lower.
is lower.
– Right view –
MAIN board
heatsink
front panel block
resistor
Note: When installing the wire,
be careful not to touch the
resistor.
HCD-EC719iP/EC919iP
11
2-7. MAIN BOARD
2-6. MAIN BOARD BLOCK
5 Solder the short-land.
Note 2: When assembling the MAIN board block,
remove the solder of short-land after
connecting all flexible flat cable
and
connector.
2 connector
(XP4)
6 flexible flat cable
(XP3)
7 MAIN board block
4 Lift the MAIN board block
in the direction of an arrow.
1 connector (XP5)
Note
3: Since the wire is very thin, it is easy to cut.
When disconnecting, do it while holding the
connector
part.
3 two claws
3 two claws
3 four claws
Note 1: Before disconnecting the flexible flat cable of the loader with FFC (TDL-5) (CDM1), solder the short-land.
7 MAIN board
2 connector
(XP2)
1 connector
(XP1)
– Rear right view –
3 screw
(silver
3
u 8)
3 screw
(silver
3
u 8)
3 two screws
(silver
3
u 8)
6 heatsink
5 three heat sink
screws
(3
(3
u 8)
5 heat sink
screw
(3
(3
u 8)
4 Remove the MAIN board block
in the direction of an arrow.
(EC919iP)
HCD-EC719iP/EC919iP
12
2-8. POWER BOARD
– Rear view –
0 POWER board
2 connector
(XP2)
1 connector
(XP1)
9 Draw out the
wires.
8 Remove the power board
in the direction of an arrow.
6 ECL7/9 shield cover
5
– Rear view –
4 six claws
4 claw
3 screw
(silver
3
u 8)
7 screw
(silver
3
u 8)
7 screw
(silver
3
u 8)
7 two screws
(silver
3
u 8)
Click on the first or last page to see other HCD-EC719IP / HCD-EC919IP service manuals if exist.