Sony HCD-DZ210D Service Manual ▷ View online
13
HCD-DZ210D
3-2. CASE, FRONT PANEL ASSY
Note:
Follow the disassembly procedure in the numerical order given.
1
The lever is moved in the direction
of the arrow with the thin rod.
2
3
loading panel
4
screw (CASE3 TP2)
5
screw
(CASE3 TP2)
7
case
qj
front panel assy
qf
three screws (+BV 3
×
6)
qs
connector (CN302)
qd
connector (CN3001)
qa
wire (flat type)
23core (CN509)
qh
claw
qg
claw
6
five screws
(+BVTP 3
×
8)
9
two screws
(+BV 3
×
6)
When re-assembling, leave 30 mm between
harnesses A and B for safety.
harnesses A and B for safety.
harnesses A
harnesses B
clamp
30mm
q;
cover (top)
8
two sheets
14
HCD-DZ210D
3-4. JACK BOARD, DDCON BOARD
3-3. FL BOARD
4
shield plate (fs)
0
FL board
9
wire (flat type)
23core (CN801)
7
wire (flat type)
13core (CN805)
3
five screws (+BVTP 2.6
×
8)
1
three rivets
2
retainer K
5
screw (+BVTP 2.6
×
8)
6
connector (CN803)
8
connector (CN811)
1
knob (vol)
2
nut
5
JACK board
qs
DDCON board
6
button (play)
4
wire (flat type)
13core (CNP802)
7
Remove soldering.
3
five screws
(+BVTP 2.6
×
8)
qa
two screws (+BVTP 2.6
×
8)
8
two screws
(+BVTP 2.6
×
8)
q;
button (power)
9
SW board
15
HCD-DZ210D
3-6. MAIN BOARD
3-5. I/O BOARD, SPEAKER BOARD
9
I/O board
qg
SPEAKER board
8
PWB support
qf
two screws (+BV 3
×
6)
7
four screws
(+BVTP 3
×
8)
q;
connector (CN303)
qa
connector (CN302)
6
wire (flat type)
11core (CN303)
1
connector (CN302)
5
wire (flat type)
13core (CN201)
4
wire (flat type)
7core (CN304)
2
wire (flat type)
13core (CN301)
3
wire (flat type)
5core (CN305)
qd
two screws
(+BVTP 3
×
8)
qs
connector (CN301)
screw
lead pin
When assembling,
clamp the three harnesses with
a lead pin or a similar tool so
that they do not touch this screw.
clamp the three harnesses with
a lead pin or a similar tool so
that they do not touch this screw.
three harnesses
8
connector
(CN3000)
2
wire (flat type) 7core (CN1302)
3
wire (flat type) 23core (CN509)
1
wire (flat type) 13core (CN1301)
9
two screws (+BV 3
×
6)
qj
four screws (+BV 3
×
6)
ql
MAIN board
qh
four screws (+BV 3
×
6)
5
connector (CN515)
qk
clamp
When re-assembling, attaching the
two heat radiation sheets on the
IC MAIN board first, and then attach
the heat sink (AMP).
two heat radiation sheets on the
IC MAIN board first, and then attach
the heat sink (AMP).
heatsink (AMP)
radiation
sheets
sheets
IC on the
MAIN board
MAIN board
qa
HEATSINK B board
qf
heatsink (AMP)
0
HEATSINK A board
qd
screw
(+BVTP 3
×
12)
qg
two radiation
sheet
4
wire (flat type) 7core (CN795)
6
connector
(CN3002)
7
connector
(CN3001)
qs
two screws (+BV 3
×
10)
When re-assembling, leave 30 mm between
harnesses A and B for safety.
harnesses A and B for safety.
harnesses A
harnesses B
clamp
30mm
After twist the harness once,
install the connector.
install the connector.
POWER board
MAIN board
16
HCD-DZ210D
3-7. JOINT BOARD
3-8. DC FAN, TUNER UNIT
7
JOINT board
6
MODULE (DAB TUNER)
3
two screws (+BV 3
×
6)
1
wire (flat type)
7core (CN710)
2
wire (flat type)
5core (CN711)
4
nut (DAB)
5
board to board connecter
7
DC fan
3
tuner unit
4
two screws
(+BVTP 3
×
8)
5
cover (fan)
1
two screws (+BVTT 3
×
6)
6
two screws
(+BVTT 4
×
8)
2
wire (flat type)
11core
Click on the first or last page to see other HCD-DZ210D service manuals if exist.