DOWNLOAD Sony HBD-EF1100 Service Manual ↓ Size: 5.77 MB | Pages: 88 in PDF or view online for FREE

NOTE  OF  REPLACING  MB1002  BOARD  OR  WLAN/
BT  COMBO  CARD 
When the MB1002 board or WLAN/BT COMBO card are re-
placed, please execute the below service mode.
1.  Please update FW to M16.R.157
2.  Whenever replace MB1002 board or WLAN/BT COMBO 

CARD please execute “Reset to Factory Default Settings” 
from XMB.

[Home menu 

 Setup  Resetting  Reset to Factory Default 

Settings 

 All Settings]

Next, go to service menu and execute “(1) Bluetooth Enable” and 
“(3) Write Bluetooth device address to Registry”.
Finally check one touch NFC listening function at normal power 
on.

Note: The operation in this mode must use a remote commander 
and TV monitor.

1. Connect this unit with TV monitor.
2. Press the 

(\/1)

 button to turn the power on.

3. Press button in order of the [DISPLAY] 

 [0]  [2]  [1]  

  [SUBTITLE] on the remote commander.
  (Make the interval when each button is pressed within two 
 seconds)
4. Enter the BD service mode. The OSD menu on TV monitor can
   be operated by remote commander.
5. Press 

 and Enter Diag.

6. Press 

 and Enter Bluetooth Device Test (Screen 1).

7. Enter (1) Bluetooth Enable, wait until the display show 
  “ Status : Bluetooth Enable Successful ” (Screen 2).
8. Enter (3) Write Bluetooth device address to Registry, wait until 
  the display show “Bluetooth Device Address” and “Status : 
  Write Successfull” (Screen 3).
9. Enter [RETURN] to the selection of test category.

 Diag

 Diag

Diag

NOTE  THE  BD  DRIVE (BPX-7)  PARTS  REPLACING
The mechanism blocks except optical device of BD drive (BPX-7) 
are chiefl y composed of the following parts.
• HOLDER, 

CHUCK 

ASSY

• LOADING 

ASSY

• COVER, 

DRIVE

These parts are produced by two venders, it is not compatible. 
Therefore, HOLDER, CHUCK ASSY and LOADING ASSY 
are supplied by one pair as repair parts. Please exchange both 
HOLDER, CHUCK ASSY and LOADING ASSY at the same 
time.

COVER, DRIVE need not be exchanged at the same time.

Note 1: The laser caution label is not pasted to LOADING FOR SER-

VICE. Please peel off an original laser caution label, and paste 
it to LOADING FOR SERVICE when you use LOADING FOR 
SERVICE.

Note 2: If laser caution label is a condition of the figure below, 
 

it is acceptable.

EF1100

4-438-896-4[]

CAPACITOR  ELECTRICAL  DISCHARGE  PROCESSING
When checking the board, the electrical discharge is necessary for 
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.

• Switching 

regulator

 

C201, C402, C503, C504

:/2 W

NOTE  OF  REPLACING  THE  IC3102  ON  THE  AMP  
BOARD  AND  THE  COMPLETE  AMP  BOARD
When IC3102 on the AMP board and the complete AMP 
board are replaced, it is necessary to spread the compound
(GREASE (G-747) 1KG) (Part No. 7-640-004-33 ) between parts 
and heat sink.
Spread the compound referring to the fi gure below.

CHECKING  METHOD  OF  NETWORK  OPERATION
It is necessary to check the network operation, when replacing the 
MB1002 board. Check the operation of wireless and wired LAN, 
according to the following method.

1.  Checking Method of Wireless LAN Operation
Check that access point is recognized surely.

Necessary Equipment:
Wireless access point with router function (AP)

1.  Press the [HOME] button on the remote commander to enter 

the home menu.

2.  Press the [m]/[M]/[<]/[,] buttons on the remote command-

er to select “Network Settings”

“Internet Settings”, and press 

the [ ] button on the remote commander.

3.  Press the [m]/[M] buttons on the remote commander to select 

“Wireless Setup (built-in)”, and press the [ ] button on the 
remote commander.

4.  The system starts searching for access points, and displays a 

list of up available network name (SSID).

5.  Check that access point (SSID) is displayed on the searching 

result.

Note: Refer to the instruction manual about details of the setting method.

2.  Checking method of wired LAN operation
Check that access point is recognized surely.

1.  Connect the main unit to the router or the hub, etc. with the 

LAN cable.

2.  Press the [HOME] button on the remote commander to enter 

the home menu.

3. Press 

the 

[m]/[M]/[<]/[,] buttons on the remote command-

er to select “Network Settings”

“Internet Settings”, and press 

the [ ] button on the remote commander.

4.  Press the [m]/[M] buttons on the remote commander to select 

“Wired Setup”, and press the [ ] button on the remote com-
mander.

5.  Press the [m]/[M] buttons on the remote commander to select 

“Auto”, and press the [ ] button on the remote commander.

6.  Press the [,] button on the remote commander.

7.  Press the [m]/[M] buttons on the remote commander to select 

“Save & Connect”, and press the [ ] button on the remote 
commander.

8.  When “Internet Settings is now complete.” appears, then press 

the [ ] button on the remote commander.

9.  Press the [HOME] button on the remote commander to enter 

the home menu.

10. Press the [m]/[M]/[<]/[,] buttons on the remote command-

er to select “Network Settings”

“Network Connection Diag-

nostics”, and press the [ ] button on the remote commander.

11. Press the [<]/[,] buttons on the remote commander to 

select “IPV4” or “IPV6”, and press the [ ] button on the 
remote commander. 

12. Check that IP address can be acquired.

Note: Refer to the instruction manual about details of the setting method.

Note 1: After the case is removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).

1 Remove the case.
 

2 Insert the clip etc.

3

Note: Push after it inserts it in this hole well.