DOWNLOAD Sony HBD-EF1100 Service Manual ↓ Size: 5.77 MB | Pages: 88 in PDF or view online for FREE

6.  Diag (Audio Input Test)
This screen performs audio input test.

Screen 1: Select Audio Input Test Category
Operation:
[<]/[,]  Selects the category

[m]/[ ] 

Activate the selected category

[RETURN] Returns to the service top menu

Screen 2: Select Input Device
After “Audio Input Test” selects in Screen 1, the device to test is 
chosen.
Operation:
[M]/[m] Selects 

Device

[ ] 

Activate and Start Test/Stop

[RETURN] Returns to the selection of test category

•  Device Test 

: Device List

Digital Input1 

: CXD90019R-BA is inputted from Optical

Digital Input2 

: CXD90019R-BA is inputted from ARC

Analog Input 

: CXD90019R-BA is inputted from AUDIO

• Audio 

Input 

Test

CXD90019R-BA is inputted from DIR/analog and outputs 
LineOut (8ch) L and R.
Check tone sound by speaker connected with LineOut (8ch) L and 
R.
(Input; LPCM 48kHz 2ch)

7.  Diag (Wireless LAN Test)
This screen performs wireless LAN test.

Screen 1: Selects the Wireless LAN test category
Operation:
[

<

]/[

,

]  Selects the category

[

m

]/[ ] 

Moves to the selected category

[RETURN]  Returns to the service top menu

Screen 2: Wireless LAN test
[1] Show WLAN Hwinfo
[2] Connect to AccessPoint
[3] Start display RSSI value.
[4] Start Ping Test
Operation:
[M]/[

m

] 

Selects the test

[ ] 

Executes the test

[RETURN]  Returns to selection of test category

Screen 2 : Select [1] Show WLAN HwInfo
• Viewing the display
Serial : Serial Number
Hard  : Hardware Version
Mac   : Mac Address

Screen 3 : Select [2] Connect to AccessPoint
Connect Access Point only with the following AP settings.
CERT: NO-ENCRYPT
WEPKEY: abcdef1234
PMK: ABCDE12345
SSID: SONY-Test-R
IPADDR: 192.168.1.100
NETMASK: 255.255.255.0
BROADCAST: 192.168.1.10
When connect to AP, Status is “Connected!”
When cannot connect to AP, Status is “can’t Connect!”

Screen 4 : Select [3] Start Display RSSI Value
Display RSSI value.

Screen 5 : Select [4 ] Start Ping Test
Ping Test.
IP address use the value of “192.168.1.10”.

 Diag

 Diag

 Diag

8.  Diag (MIC Input Test)
This screen performs MIC input test.

Note: Not used for the servicing.

9.  Diag (HDMI Input Test)
This screen performs HDMI input test.

Note: Not used for the servicing.

Note: Not used for the servicing.

11. Diag (Bluetooth Device Test)
This screen performs Bluetooth Device Test.

Screen 1: Select Bluetooth Device Test Category
Operation:
[<]/[,]  Selects the category

[m]/[ ] 

Activate the selected category

[RETURN] Returns to the service top menu

Screen 2: Select Bluetooth Device Test
Operation:
[1] Bluetooth Enable
[2] Bluetooth Disable
[3] Write Bluetooth device address to Registry.
[4] Bluetooth Inquiry Test
[M]/[m] Selects 

Device

[ ] 

Activate and Start Test

[RETURN] Returns to the selection of test category

Screen 2: Select [1] Bluetooth Enable
• Viewing the Status display, if
  Successful: “Bluetooth Enable Successful!”
  Fail: “Bluetooth Enable Fail!”

Screen 3 : Select [2] Bluetooth Disable
• Viewing the Status display, if
  Successful: “Bluetooth Disable Successful!”
  Fail: “Bluetooth Disable Fail!”

Screen 4 : Select [3] Store Bluetooth device address to 
Registry
Display will show : Bluetooth device address : “xx:xx:xx:xx:xx:xx”
• Viewing the Status display, if
  Successful: “Write Successful!”
  Fail: “Write Fail!”

Diag

Diag

Diag

 Diag

 Diag

 Diag

 Diag

Diag

Diag

12. Log: Error Log (Output of each Log)
This screen displays the contents of each log.

Note: Do not refer to the displayed date.

Screen 1: Selects log
Operation:
[1]/[ ] 

Moves to the Error Log output screen

[RETURN]  Returns to the top menu of the service mode

Screen 2: Displays the Error Log
Operation:
[

<

] 

Returns to the previous page

[

,

] 

Moves to the next page

[RETURN] Returns to the screen (Screen 1) that selects the log 

type

[RED] 

Writes the log contents to an USB memory device

•  Viewing the log display
Error Log:
 

[174] 2010/01/01 00:00:08 [ErrCode:0902A4053002]

 

[Index number] [Date] [Time] [Error code]

About copying log to USB memory device:
Press the [RED] button in each log display screen with the USB 
memory device inserted into the unit.

Note: Please do not press the [RED] button immediately after USB mem-

ory is inserted. 

 

  Please do not pull out USB memory immediately after the [RED] 

button was pressed.

Error Log:
 When 

“getErrLogFile.trm 

fi le” exists in the USB memory de-

vice, errlog.log fi le is output.

 Select Log

 Error Log

There is a possibility that this mode cannot be correctly execut-
ed. Never use this mode.

14. Network (Network Test Diagnosis Screen: Ifconfi g)
Network menu for the wired ethernet.

Screen 1: Ifconfi g Test
Operation:
[ ] Activate Ifconfi g (Display network setting)
[,] 

Select ping test

[RETURN] Returns to the top menu of the service mode

Screen 2: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[RETURN]  Returns to the top menu of the service mode
(The details of a Ping test are “14. Network (Network Test Diagno-
sis Screen: Ping)”)

Screen 3: Ifconfi g Test Active
Display Ifconfi g command results.
Operation:
[ ] Ifconfi g retry
[,] Select 

Ping Test

[RETURN]  Returns to the top menu of the service mode

15. Network (Network Test Diagnosis Screen: Ping)
Ping test for the wired ethernet.

Screen 1: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[

m

] 

Ping execution preparation

[RETURN]  Returns to the top menu of the service mode

When “Ping to :>” is reversed, the [ ] button is pressed and IP 
is inputted.
Operation:
[ ] 

Finish to input

[RETURN]  Finish to input
[

<

] 

Finish to input and Select Ifconfi g Test

[0] to [9] 

Input Character sting ‘0-9’

Screen 3: Ping Test Active
When [START] is reversed, the [ ] button is pressed and execute 
ping.
Operation:
[ ] 

Activate ping test

[

M

] 

The IP address of the ping point is set up

[RETURN]  Returns to the top menu of the service mode

 Network

 Network

 Network

 Network

 Network