Sony HBD-E190 / HBD-E290 / HBD-E490 / HBD-E690 Service Manual ▷ View online
HBD-E190/E290/E490/E690
9
MODEL IDENTIFICATION
- Rear view -
- Rear view -
Model
Part No.
E190: CND, MX6
4-295-427-0[]
E190: AEP, UK, RU, SAF, SP, AUS
4-295-427-1[]
E290: PX
4-295-427-2[]
E290: AEP, UK, RU, SAF, SP, AUS, E3, EA,
TW, TH, CH, E12, E32
4-295-427-3[]
E490: CND, MX6
4-295-427-4[]
E490: AEP, UK, RU, SP, E3, EA, TW, TH,
CH, E12, E15
4-295-427-5[]
E690: AEP, SP, EA, E15, E3, E12, RU,
AUS, TH
4-295-427-6[]
• Abbreviation
AUS :
AUS :
Australian
model
CH
: Chinese model
CND : Canadian model
E3
E3
: 240 V AC area in E model
E12
: 220-240 V AC area in E model
E15
: Iran model
E32
: 110-240 V AC area in E model
EA
: Saudi Arabia model
MX6 : Latin-American model
PX
PX
: PX model
RU
: Russian model
SAF : South African model
SP
SP
: Singapore model
TH :
Thai
model
TW :
Taiwan
model
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
• Switching
regulator
C207, C201, C402, C503, C504, C507
NOTE THE BD DRIVE (BPX-7) PARTS REPLACING
The mechanism blocks except optical device of BD drive (BPX-7)
are chiefl y composed of the following parts.
• HOLDER,
The mechanism blocks except optical device of BD drive (BPX-7)
are chiefl y composed of the following parts.
• HOLDER,
CHUCK
ASSY
• LOADING
ASSY
• COVER,
DRIVE
These parts are produced by two venders, it is not compatible.
Therefore, HOLDER, CHUCK ASSY and LOADING ASSY
are supplied by one pair as repair parts. Please exchange both
HOLDER, CHUCK ASSY and LOADING ASSY at the same
time.
Therefore, HOLDER, CHUCK ASSY and LOADING ASSY
are supplied by one pair as repair parts. Please exchange both
HOLDER, CHUCK ASSY and LOADING ASSY at the same
time.
COVER, DRIVE need not be exchanged at the same time.
Note 1: The laser caution label is not pasted to LOADING FOR SER-
VICE. Please peel off an original laser caution label, and paste
it to LOADING FOR SERVICE when you use LOADING FOR
SERVICE.
it to LOADING FOR SERVICE when you use LOADING FOR
SERVICE.
LABEL, LASER CAUTION
HOLDER, CHUCK ASSY
LOADING ASSY
LOADING FOR SERVICE
/LPLWVDPSOHLQVWDWHRIODVHUFDXWLRQODEHO
Note 2: If laser caution label is a condition of the figure below,
it is acceptable.
COVER, DRIVE
– SWITCHING REGULATOR (Conductor Side) –
(To both ends of each capacitor)
800
:/2 W
C201
C207
C402
C504 C503
C507
Part No.
Ver. 1.1
HBD-E190/E290/E490/E690
10
NOTE OF REPLACING THE IC3102 AND IC3302 ON
THE AMP BOARD AND THE COMPLETE AMP BOARD
When IC3102 and IC3302 on the AMP board and the complete
AMP board are replaced, it is necessary to spread the compound
(GREASE (G-747)) 1KG) (Part No. 7-640-004-33 ) between parts
and heat sink.
Spread the compound referring to the fi gure below.
THE AMP BOARD AND THE COMPLETE AMP BOARD
When IC3102 and IC3302 on the AMP board and the complete
AMP board are replaced, it is necessary to spread the compound
(GREASE (G-747)) 1KG) (Part No. 7-640-004-33 ) between parts
and heat sink.
Spread the compound referring to the fi gure below.
CHECKING METHOD OF NETWORK OPERATION
It is necessary to check the network operation, when replacing the
MB148 board. Check the operation of wired LAN, according to
the following method.
It is necessary to check the network operation, when replacing the
MB148 board. Check the operation of wired LAN, according to
the following method.
1. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [
] button on the remote com-
mander.
5. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Auto”, and press the [
] button on the remote
commander.
6. Press the [
,] button on the remote commander.
7. Press the [
m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [
] button on the remote
commander.
8. When “Internet Settings is now complete.” appears, then press
the [
] button on the remote commander.
9. Press the [HOME] button on the remote commander to enter
the home menu.
10. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
11. Press the [
m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [
] button
on the remote commander.
12. Press the [
<]/[,] buttons on the remote commander to
select “Start”, and press the [
] button on the remote com-
mander.
13. Check that IP address can be acquired.
Note: Refer to the instruction manual about details of the setting method.
– AMP Board (Component Side) –
IC3102
IC3302
IC3302
IC3102
HBD-E190/E290/E490/E690
11
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note 1: After the left panel is removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
SERVICE POSITION
Ver. 1.1
MB148 board
AMP board
BD drive
(BPX-7)
(BPX-7)
POWER KEY board
KARAOKE board
(RU)
(RU)
PANEL board
switching regulator (SWR1)
(3L382W-1) (E290: AEP, UK, SAF, SP, AUS, TW, TH, CH/
(3L382W-1) (E290: AEP, UK, SAF, SP, AUS, TW, TH, CH/
E490: CND, AEP, UK, SP, TW, TH, CH/
E690: AEP, SP, AUS, TH)
(3L382W) (E290: RU, E3, EA, PX, E12, E32/
E490: RU, MX6, E3, EA, E12, E15/
E690: RU, E3, EA, E12, E15)
(3L383W-1) (E190: CND, AEP, UK, SAF, SP, AUS)
(3L383W) (E190: RU, MX6)
(3L383W) (E190: RU, MX6)
1 Remove the panel, left.
(Illustration of disassembly is omitted.)
2 Insert the clip etc.
3
tray
tray
BD drive
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
8 cm or more
hole
–
Side view
–
–
Top view
–
Note: Push after it inserts it in this hole well.
• Abbreviation
AUS :
AUS :
Australian
model
CH
: Chinese model
CND : Canadian model
E3
E3
: 240 V AC area in E model
E12
: 220-240 V AC area in E model
E15
: Iran model
E32
: 110-240 V AC area in E model
EA
: Saudi Arabia model
MX6 : Latin-American model
PX
PX
: PX model
RU
: Russian model
SAF : South African model
SP
SP
: Singapore model
TH :
Thai
model
TW :
Taiwan
model
HBD-E190/E290/E490/E690
12
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-3. LEFT PANEL, RIGHT PANEL
(Page
(Page
14)
SET
2-2. HOW TO BEND FFC
(Page
(Page
13)
2-11. OPTICAL PICK-UP BLOCK (KEM480AAA),
WIRE (FLAT TYPE)
(Page
19)
2-6. TOP CHASSIS, KARAOKE BOARD (RU),
POWER KEY BOARD, PANEL BOARD
(Page
16)
2-10. AMP BOARD
(Page
(Page
18)
2-9. SWITCHING REGULATOR (SWR1)
(Page
(Page
18)
2-7. BD DRIVE (BPX-7)
(Page
(Page
17)
2-4. LOADING
PANEL
(Page
14)
2-8. MB148
BOARD
(Page
17)
2-5. TOP PANEL, FRONT PANEL ASSY
(Page
(Page
15)
Ver. 1.1
Click on the first or last page to see other HBD-E190 / HBD-E290 / HBD-E490 / HBD-E690 service manuals if exist.